• 한국컴퓨터그래픽스학회논문지
• /
• 제29권3호
• /
• pp.117-125
• /
• 2023

가상 시뮬레이션을 이용한 의류 디자인 개발에서는 가상과 실제의 차이가 최소화되어야 한다. 가상 의상과 실제 의상의 유사성을 높이는 데에 가장 기본이 되는 작업은 의상 제작에 사용될 옷감의 물성을 최대한 유사하게 표현할 수 있는 시뮬레이션 파라미터를 찾는 것이다. 시뮬레이션 파라미터 최적화 절차에는 전문가의 수작업으로 이루어지는 튜닝 과정이 포함되는데, 이 작업은 높은 전문성과 많은 시간이 요구된다. 특히 조정된 시뮬레이션 파라미터를 적용한 결과를 다시 확인하기 위해 시뮬레이션을 반복적으로 실행할 때 많은 시간이 소요된다. 최근 이 문제를 해결하기 위해 파라미터 튜닝에 주로 사용되는 드레이프 테스트 시뮬레이션 결과를 빠르게 추정하는 인공신경망 학습 모델이 제안되었다. 하지만 기존 연구에서는 비교적 간단한 선형 강성 모델을 사용하였으며 드레이프 시뮬레이션 전체를 추정하는 대신 일부만 추정하고 나머지는 보간하는 방식을 사용하였다. 실제 의류 디자인 개발 과정에서는 주로 비선형 강성 모델이 적용된 시뮬레이터가 사용되지만, 이에 대한 연구는 아직 부족하다. 본 논문에서는 비선형 강성 모델을 대상으로 드레이프 시뮬레이션 결과를 추정하기 위한 새로운 학습 모델을 제안한다. 본 연구에서 제안된 학습 모델은 시뮬레이션 결과인 고해상도 메시 모델 전체를 추정한다. 제시하는 방법의 성능을 검증하기 위해 세 가지 드레이프 테스트 방식을 대상으로 실험을 진행하여 추정 정확도를 평가한다.

• 비파괴검사학회지
• /
• 제28권6호
• /
• pp.504-511
• /
• 2008

This paper proposes an ultrasonic measurement method for measurement of linear interfacial stiffness of contacting surface between two steel plates subjected to nominal compression pressures. Interfacial stiffness was evaluated by using shear waves reflected at contact interface of two identical solid plates. Three consecutive reflection waves from solid-solid surface are captured by pulse-echo method to evaluate the state of contact interface. A non-dimensional parameter defined as the ratio of their peak-to-peak amplitudes are formulated and used to calculate the quantitative stiffness of interface. Mathematical model for 1-D wave propagation across interfaces is developed to formulate the reflection and transmission waves across the interface and to determine the interfacial stiffness. Two identical plates are fabricated and assembled to form contacting surface and to measure interfacial stiffness at different states of contact pressure by means of bolt fastening. It is found from experiment that the amplitude of interfacial stiffness is dependent on the pressure and successfully determined by employing pulse-echo ultrasonic method without measuring through-transmission waves.

• Structural Engineering and Mechanics
• /
• 제10권1호
• /
• pp.27-36
• /
• 2000

The Oktalok nodal connection system is an aesthetic and efficient system. It has been widely used throughout Australia. The paper will briefly introduce the concept and application of the Oktalok nodal system. The existing design method is based on the assumption that the joints are pin-ended, i.e., the rotational stiffness of the joints is zero. However the ultimate capacity of the frame may increase significantly depending on the rotational stiffness of the joints. Stiffness tests and finite element simulations were carried out to determine the rotational stiffness of the Oktalok joints. Column buckling tests and non-linear finite element analyses were performed to determine the member capacity of columns with semi-rigid end conditions. A simple formulae for the effective length factor of column buckling is derived based on the above experimental and theoretical investigations.

• 한국항공우주학회지
• /
• 제38권6호
• /
• pp.612-619
• /
• 2010

본 연구에서는 비선형 유한요소법을 사용하여 헬리콥터용 구형 탄성체베어링을 설계하였다. 탄성체베어링은 헬리콥터 로터허브의 주요부품으로 로터블레이드의 플래핑운동, 래그운동, 피치운동의 힌지 역할을 한다. 탄성체베어링은 고무판과 금속판으로 구성된다. 탄성체 베어링은 고무의 탄성변형을 이용하여 힌지 역할을 하기 때문에 강성설계가 중요하다. 따라서 탄성체베어링은 로터허브 베어링의 강성요구 조건을 만족하도록 설계되어야한다. 본 연구에서는 구형의 탄성체베어링의 효율적인 설계를 위하여 유한요소모델 생성 알고리즘을 개발하고, 단일 고무판의 강성 특성을 분석을 수행하였다. 끝으로, 본 연구에서 설계한 탄성체베어링의 헬리콥터 로터허브용으로 적합한지 검증하였다.

• Steel and Composite Structures
• /
• 제1권2호
• /
• pp.245-268
• /
• 2001

The analysis of steel-concrete composite joints presents some particular aspects that increase their complexity when compared to bare steel joints. In particular, the influence of slab reinforcement and column concrete encasement clearly change the moment-rotation response of the joint. Starting from an energy approach developed in the context of steel joints, an extension to composite joints is presented in this paper that is able to provide closed-form analytical solutions. In addition, the possibility of tri-linear or non-linear component behaviour is also incorporated in the model, enabling adequate treatment of the influence of cracked concrete in tension and the softening response of the column web in compression. This methodology is validated through comparison with experimental tests carried out at the University of Coimbra.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.623-630
• /
• 2006

In this paper, a geometric nonlinear analysis procedure of beam-column element including multi-noded cable element is presented. For this, first a stiffness matrix about beam-column element which considers the second effect of initial force supposing the curved shape at each time step with Hermitian polynomials as the shape function is derived and second, tangent stiffness matrix about multi-noded cable element being too. To verify geometric nonlinearity of this newly developed multi-noded cable-truss element, IPS(Innovative Prestressed Support) system using this theory is analysed by geometric nonlinear method and the results are compared with those by linear analysis.

• Structural Engineering and Mechanics
• /
• 제25권1호
• /
• pp.53-73
• /
• 2007

In this study, an effective load increment method for multi modal adaptive non-linear static (pushover) analysis (NSA) for building type structures is presented. In the method, lumped plastisicity approach is adopted and geometrical non-linearties (second-order effects) are included. Non-linear yield conditions of column elements and geometrical non-linearity effects between successive plastic sections are linearized. Thus, load increment needed for formation of plastic sections can be determined directly (without applying iteration or step-by-step techniques) by using linearized yield conditions. After formation of each plastic section, the higher mode effects are considered by utilizing the essentials of traditional response spectrum analysis at linearized regions between plastic sections. Changing dynamic properties due to plastification in the system are used on the calculation of modal lateral loads. Thus, the effects of stiffness changes and local mechanism at the system on lateral load distribution are included. By using the proposed method, solution can be obtained effectively for multi-mode whereby the properties change due to plastifications in the system. In the study, a new procedure for determination of modal lateral loads is also proposed. In order to evaluate the proposed method, a 20 story RC frame building is analyzed and compared with Non-linear Dynamic Analysis (NDA) results and FEMA 356 Non-linear Static Analysis (NSA) procedures using fixed loads distributions (first mode, SRSS and uniform distribution) in terms of different parameters. Second-order effects on response quantities and periods are also investigated. When the NDA results are taken as reference, it is seen that proposed method yield generally better results than all FEMA 356 procedures for all investigated response quantities.

• Structural Engineering and Mechanics
• /
• 제53권4호
• /
• pp.791-818
• /
• 2015

RC buildings constitute the prevailing type of construction in earthquake-prone region like Kathmandu Valley. Most of these building constructions were based on conventional methods. In this context, the present paper studied the seismic behaviour of existing RC buildings in Kathmandu Valley. For this, four representative building structures with different design and construction, namely a building: (a) representing the non-engineered construction (RC1 and RC2) and (b) engineered construction (RC3 and RC4) has been selected for analysis. The dynamic properties of the case study building models are analyzed and the corresponding interaction with seismic action is studied by means of non-linear analyses. The structural response measures such as capacity curve, inter-storey drift and the effect of geometric non-linearities are evaluated for the two orthogonal directions. The effect of plan and vertical irregularity on the performance of the structures was studied by comparing the results of two engineered buildings. This was achieved through non-linear dynamic analysis with a synthetic earthquake subjected to X, Y and $45^{\circ}$ loading directions. The nature of the capacity curve represents the strong impact of the P-delta effect, leading to a reduction of the global lateral stiffness and reducing the strength of the structure. The non-engineered structures experience inter-storey drift demands higher than the engineered building models. Moreover, these buildings have very low lateral resistant, lesser the stiffness and limited ductility. Finally, a seismic safety assessment is performed based on the proposed drift limits. Result indicates that most of the existing buildings in Nepal exhibit inadequate seismic performance.

• 한국기계가공학회지
• /
• 제13권5호
• /
• pp.8-14
• /
• 2014

A slewing reducer consists of two planetary gearsets which require a good load distribution over the gear tooth flank for enhanced durability. This work investigates how the bearing characteristics influence the load distribution over the gear tooth flank. A complete system model is developed to analyze a slewing reducer, including the non-linear mesh stiffness of the gears and the non-linear stiffness of bearings. The results indicate that the type, arrangement and preload of the output shaft bearings greatly influence the gear mesh misalignment, contact pattern, face load factor, gear safety factor and lifetimes of the parts.

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.29-35
• /
• 2013

The pitch reducer consists of several planetary gearsets, and they should have good load distribution over gear tooth flank and load sharing among the planets to improve the durability. This work investigates how bearing internal clearances influence both the load distribution over the gear tooth flank and the planet load sharing. A whole system model is developed to analyze a pitch reducer. The model includes non-linear mesh stiffness of gears, non-linear stiffness of bearings. The results indicate that the face load factor and mesh load factor decrease, and the fatigue life of output shaft bearings increase as bearing internal clearances of output shaft decrease. Therefore, the internal clearance of output shaft bearing must be considered when designing the pitch reducer for wind turbines.