• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.5
• /
• pp.466-471
• /
• 2015

In this paper, the design technique of the wide swath TOPS(Terrain Observation by Progressive Scan) imaging mode is introduced. The TOPS mode overcomes the scalloping limitations imposed by ScanSAR mode by steering the antenna pattern along track direction during the acquisition of a burst. This paper reports the operation concept of TOPS imaging and mode design result to extract the SAR operational parameters. Finally, several analyzed results such as IRF(Impulse Response Function), NESZ(Noise Equivalent Sigma Zero) and DTAR(Distributed Target Ambiguity Ratio) are presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.75-78
• /
• 2001

Recently, the HFPD measurement testing is widely used in partial discharge measurement of HV machines because HFPD measurement testing receives less influence of external noise and has a merit of good sensitivity. Also HFPD testing is able to offer the judgement standard of degradation level of HV machine and can detect discharge signals in live-line. Therefore it is very useful method compare to previous conventional PD testing method and effective diagnosis method in power transformer that requires live-line diagnosis. But partial discharges have very complex characteristics of discharge pattern so it is required continuous research to development of precise analysis method. In recent, the study of partial discharge is carrying out discover of initial defect of power equipment through condition diagnosis and system development of degradation diagnosis using HFPD(High Frequency Partial Discharge) detection. In this study, simulated transformer is manufactured and HFPD occurred from transformer is measured with broad band antenna in real time, the degradation grade of transformer is analyzed through produced patterns in simulated transformer according to applied voltages.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.2
• /
• pp.182-190
• /
• 2009

GPS receivers can be disrupted by intentional or unintentional jamming, then it is unable to receive GPS signals and it is impossible to get the correct navigation results. Anti-jamming schemes using array antennas are being studied well due to high performance of those, and the efforts to apply them to GPS receiver are also being done. A GPS receiver structure for a multiple beam-forming scheme among those schemes has been proposed in this paper, and the performance is also compared with that using a general GPS receiver structure. For a general GPS receiver structure, each satellite signal which is formed by a beam-forming scheme is summed to be processed in a part of digital signal processing. For a proposed GPS receiver structure, however, each satellite signal is respectively processed by a designated channel in a part of digital signal processing. Finally, it is confirmed that the proposed GPS receiver structure is superior to a general GPS receiver structure in a point of the carrier to noise power ratio and the navigation accuracy using a software platform.

• The KIPS Transactions:PartC
• /
• v.12C no.7 s.103
• /
• pp.1025-1030
• /
• 2005

Cooperative communications among users in multiple access wireless environments is an efficient way to obtain the powerful benefits of multi-antenna systems without the demand for physical arrays. This paper proposes a solution to optimize the weights of partnering users' signals for the minimum error probability at the output of maximum likelihood (ML) detector under the transmit power constraints by taking advantage of channel state information (CSI) feedback from the receiver to the transmitter. Simulation programs are also established to evaluate the performance of the system under flat Rayleigh fading channel plus AWGN (Additive White Gaussian Noise).

• Journal of Communications and Networks
• /
• v.10 no.2
• /
• pp.186-193
• /
• 2008

A two-hop multiple-input multiple-output (MIMO) relay network which comprises a multiple antenna source, an amplify-and-forward MIMO relay and many potential users are studied in this paper. Consider the achievable sum rate as the performance metric, a joint design method for the processing units of the BS and relay node is proposed. The optimal structures are given, which decompose the multiuser MIMO relay channel into several parallel single-input single-output relay channels. With these structures, the signal-to-noise ratio at the destination users is derived; and the power allocation is proved to be a convex problem. We also show that high sum rate can be achieved by pairing each link according to its magnitude. The sum rate of three broadcast strategies, time division multiple access (TDMA) to the strongest user, dirty paper coding (DPC), and beamforming (BF) are investigated. The sum rate bounds of these strategies and the sum capacity (achieved by DPC) gain over TDMA and BF are given. With these results, it can be easily obtained that how far away TDMA and BF are from being optimal in terms of the achievable sum rate.

• Journal of The Korean Astronomical Society
• /
• v.47 no.6
• /
• pp.201-207
• /
• 2014

We report the development of solar flux receivers operating at 2.8 GHz to monitor solar radio activity. Radio waves from the sun are amplified, filtered, and then transmitted to a power meter sensor without frequency down-conversion. To measure solar flux, a calibration scheme is designed with a noise source, an ambient load, and a hot load at $100^{\circ}C$. The receiver is attached to a 1.8 m parabolic antenna in Icheon, owned by National Radio Research Agency, and observation is being conducted during day time on a daily basis. We compare the solar fluxes measured for last seven months with solar fluxes obtained by DRAO in Penticton, Canada, and by the Hiraiso solar observatory in Japan, and finally establish equations to convert observed flux to the so-called Penticton flux with an accuracy better than 3.2 sfu.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.321-326
• /
• 2018

This study describes the design and implementation of TRM(Transmit and Receiver Module) for detection for targets of small RCS(Radar Cross Section). Through the pre-simulation analysis of radar system about RF, the main specifications of TRM are verified. After the fabrication of TRM, the main characteristics such as the maximum output, noise figure, spurious were confirmed. In the future, the radar system test will be carried out by assembling TRMs, antenna radiator, and the transceiver that generates and receivers the radar waveform reflected.

• Journal of information and communication convergence engineering
• /
• v.13 no.4
• /
• pp.241-247
• /
• 2015

Cognitive radio has been attracting increased attention as an effective approach to improving spectrum efficiency. One component of cognitive radio, spectrum sensing, has an important relationship with the performance of cognitive radio. In this paper, after a summary and analysis of the existing spectrum-sensing algorithms, we report that the existing eigenvalue-based semi-blind detection algorithm and blind detection algorithm have not made full use of the eigenvalues of the received signals. Applying multi-antenna systems to cognitive users, we design a variety of spectrum-sensing algorithms based on the joint distribution of the eigenvalues of the received signal. Simulation results validate that the proposed algorithms in this paper are able to detect whether the signal of the primary user exists or not with high probability of detection in an environment with a low signal-to-noise ratio. Compared with traditional algorithms, the new algorithms have the advantages of high detection performance and strong robustness

• Journal of Communications and Networks
• /
• v.13 no.3
• /
• pp.240-249
• /
• 2011

Cooperative diversity protocols have attracted a great deal of attention since they are thought to be capable of providing diversity multiplexing tradeoff among single antenna wireless devices. In the high signal-to-noise ratio (SNR) region, cooperation is rarely required; hence, the spectral efficiency of the cooperative protocol can be improved by applying a proper cooperation selection technique. In this paper, we present a simple "cooperation selection" technique based on instantaneous channel measurement to improve the spectral efficiency of cooperative protocols. We show that the same instantaneous channel measurement can also be used for relay selection. In this paper two protocols are proposed-proactive and reactive; the selection of one of these protocols depends on whether the decision of cooperation selection is made before or after the transmission of the source. These protocols can successfully select cooperation along with the best relay from a set of available M relays. If the instantaneous source-to-destination channel is strong enough to support the system requirements, then the source simply transmits to the destination as a noncooperative direct transmission; otherwise, a cooperative transmission with the help of the selected best relay is chosen by the system. Analysis and simulation results show that these protocols can achieve higher order diversity with improved spectral efficiency, i.e., a higher diversity-multiplexing tradeoff in a slow-fading environment.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.1
• /
• pp.39-44
• /
• 2013

In this paper digital phase-shifter for multi-arm spiral antennas was designed by using Hilbert transform. All frequency components in input signal are phase-shifted for 90 degree by Hilbert transform, and the transform is implemented by FIT and IFIT. Digital phase-shifter generates two signals with phase difference of 90 degree by using Hilbert transform from input signals sampled by analog-digital converter(ADC), and then the input signal is phase-shifted for a given phase by using two signals. Hilbert transform based on digital phase-shifter is designed by Xilinx System generator, and the effects of input noise, FIT point, sampling period, initial phase of input signal, and shifted phase are simulated and its results are compared with Matlab results.