• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.2
• /
• pp.329-334
• /
• 2016

In this paper, we demonstrate a Non-Foster matching method for an electrically small antenna to improve the signal-to-noise ratio (SNR) of communication link. For the experiment, we used a general FM antenna whose resonance frequency is about 52-57 MHz and a floating type Linvill negative impedance converter(NIC)-based circuit as a Non-Foster matching element. By implementing the Non-Foster circuit to cover FM band, we can achieve a wide bandwidth matching covers 40-200 MHz. Our measurement shows 3-7 dB improvement of SNR for the same bandwidth though there are several spikes which means no improvement of SNR in the band.

• 전기의세계
• /
• v.29 no.9
• /
• pp.584-593
• /
• 1980

Conventional radar antenna systems are susceptible to performance degradation caused by unwanted signals received via the antenna sidelobes and/or mainlobes. Adaptive array systems offer possible solution to this interference problem by automatically steering nulls to unwanted signals providing significant system performance improvement. Another important andvantage of the adaptive array is its self-optimization capability which uses the collective incoming noise data for the nulling purposes. This paper provides a tutorial introduction to adaptive arrays as well as some new development of recent research in this area. Optimum link between the antenna theory and signal processing has been sought by illustrating the gain patterns and output signal-to-noise ratio. Signal acqusition methods are shown including a new attempt of the use of spread-spectrum techniques in conjuction with array systems.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37A no.10
• /
• pp.865-875
• /
• 2012

In this paper, we optimize antenna locations for a distributed antenna system (DAS) with distributed antenna (DA) ports equipped with multiple antennas under per-DA port power constraint. Maximum ratio transmission and scaled zero-forcing beamforming are employed for single-user and multi-user DAS, respectively. Instead of maximizing the cell average ergodic sum rate, we focus on a lower bound of the expected signal-to-noise ratio (SNR) for the single-cell scenario and the expected signal-to-leakage ratio (SLR) for the two-cell scenario to determine antenna locations. For the single-cell case, optimization of the SNR criterion generates a closed form solution in comparison to conventional iterative algorithms. Also, a gradient ascent algorithm is proposed to solve the SLR criterion for the two-cell scenario. Simulation results show that DAS with antenna locations obtained from the proposed algorithms achieve capacity gains over traditional centralized antenna systems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.346-349
• /
• 2005

The present study aims to design electrically and structurally effective antenna structures in order that the structural surface itself could become the antenna. The basic design concept is composite sandwich structure in which microstrip antenna is embedded and this is termed composite smart structure (CSS). The most important outstanding problem is that composite materials of structural function cannot be used without reducing antenna efficiency. Unfortunately, such materials have high electrical loss. This is a significant design problem that needs to be solved in practical applications. Therefore, the effect of composites facesheet on antenna performances is studied in the first stage. Changes in the gain of microstrip antenna due to composites facesheet have been determined. 'Open condition' is defined when gain is maximized and is a significant new concept in the design of high-gain antennas considering bandwidth in practical application. The open condition can be made with any thickness of outer facesheet by controlling its position. In the design of CSS, glass/epoxy composites and Nomex honeycomb were used with exploiting open condition. Experiments, confirm that the gain is improved (over 11 dBi) and the bandwidth is also as wide as specified in our requirements (over 10% at 12.2 GHz). With the open condition, wideband antenna can be integrated with mechanical structures without reducing any electrical performances, as confirmed experimentally here.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2004-2010
• /
• 2018

We propose a small active antenna to receive Global Navigation Satellite System (GNSS) signals, i.e., Global Positioning System (GPS) L1 (1,575MHz) and Russian Global Navigation Satellite System (GLONASS) L1 (1,600 MHz) signals. A two-stage low-noise amplifier (LNA) with more than 27 dB gain is implemented in the bottom layer of a three-layer antenna package. In addition, a hybrid coupler is used to combine signals from pair of proximately coupled orthogonal feeds with $90^{\circ}$ phase difference to achieve the circular polarization (CP) characteristic. Three layers of high permittivity (${\varepsilon}_r=10$) substrates are stacked and effectively integrated to have a small dimension of $64mm{\times}64mm{\times}7.42mm$ (including both circuit and antenna). The reflection coefficient of the fabricated antenna at the target frequency is below -10 dB, the measured antenna gain is above 26 dBic and the measured noise figure is less than 1.4 dB.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.85-91
• /
• 2013

In this paper, the parabolic antenna aims to the precise location of a moving ship or car that can be designed system using the gyro sensor. The parabolic antenna has controlled by stepping motor that is a lot of noise and slow response of speed. It has solved the problem which is noise and slow response using the BLDC motor. Also, in order to suppress the noise two-axis control and a separate encoder to the six degrees of freedom motion system was implemented in a precise location. Generally, the gyro sensor is not required to system that doesn't move the six degrees of freedom motion system. But the system will be applied to the moving such as ships or cars. Finally, we presented the position control algorithm at the sometimes controlled both gyro sensor and BLDC motor. This system was tracking that the location of the antenna to the desired angle and errors almost didn't happen when the system was moved 6 degrees of freedom.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.99-107
• /
• 1996

When GPS (global positioning system) is used as synchronous signal in CDMA digital cellular base station system and high speed digital synchronous communication network, antenna cable length is increased, comparing with other GPS application such as positioning or car navigation. In this paper, it is proposed that a type of new GPS antenna system including RF stage for reduction of cable loss in case of long cable.The antenna system with TMPA(truncated-corners microstrip patch antenna) is designed and fabricated because GPS signal has RHCP (right-hand circular polarization), consequently antenna size can be made small size. LNA (low noise amplifier) is designed by using HEMT(high electron mobility transistor)which has lower noise figurae and better AGC characteristics at low voltage than GaAs FET, and we equiped mixer, in GPS antenna unit, which converts from 1575.42MHz to 75.42MHz. As result of comparing between typical system and proposed system when cable length is 60m, 63dB, 55dB and 25dB gain are obtained for RG-316/U, RG-58C/U and RG-213/U, and better characteristics are achieved than typical system as far as cable length is longer.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.10
• /
• pp.951-959
• /
• 2011

In this study, an OTM(on-the-move) antenna which is mounted on ground vehicles and is used for mobile communication between vehicle and satellite while moving was addressed. Since LOS(line-of-sight) of antenna should direct satellite consistently while vehicle moving to guarantee high satellite communication quality, active antenna LOS stabilization is a core technology for OTM antenna. Stabilization of a satellite tracking antenna which consists of 2-DOF gimbals, an elevation gimbal over an azimuth gimbal, was considered in this study. In consideration of driving mechanism which consists of gear train and flexible driving shafts, a two-mass-system dynamic model coupled with vehicle motion was presented. An internal PI-control loop + outer PI-control loop structure has been suggested in order to damp the torsional vibration and stabilize control system. The classical pole-placement method was applied to design control gains. In addition, a vehicle motion compensation control beside of the feedback control loop has been suggested to improve LOS stabilization performances. The feasibility of the proposed control design was verified along with some experimental results.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.3
• /
• pp.152-155
• /
• 2013

In this paper, the reduction of the figure of merit depending on the increased spill-over when the parabolic reflector is cut off partially for low-profile configuration in the satellite broadcast receiving antenna is analyzed. Also for the accurate analysis and simulation, it is considered that the noise temperature is increased due to the effect of ground thermal noise toword the sidelobes and back lobes when the antenna is tracked from $0^{\circ}$ to $60^{\circ}$ in elevation angle, and that the total noise temperature is increased because to the noise figure of LNA. As the results, noise temperature is increased up to about 15K and G/T ratio is decreased to about 2.5dB, when the reflector is cut 35% off partially.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.470-473
• /
• 2004

This paper presents conducted emission noise measurement from electronic equipment in frequency range of 1 MHz up to 30 MHz by small loop antenna. Small loop antenna measurement method can measure common-mode (CM) and differential-mode (DM) component of the noise on a pair of power line at the same time. The CM and DM can be measured separately. The theory of this measurement method is introduced and analyzed. The measured results were compared with the conventional measurement by Line Impedance Stabilization Network (LISN) and result a good trend between those methods.