• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.9
• /
• pp.823-830
• /
• 2013

The purpose of this study is to develop a noise reduction device installed at the top of noise barrier for further decreasing of noise level of 400 km/h class high-speed railroad. For this, the frequency spectrum of 400 km/h class high-speed railroad was analyzed through the field noise test, and the tuning frequency was determined to design a noise reduction device. The noise reduction device was designed to have noise reduction performance of at least 3 dB(A) using the prediction method(2D BEM) and through the laboratory test with the prototype. Finally, the outdoor test showed that this device could decrease noise level of 400 km/h class high-speed railroad even more than 3 dB(A).

• Journal of Environmental Impact Assessment
• /
• v.20 no.6
• /
• pp.787-795
• /
• 2011

Noise barrier is generally used with welding of joint rail for railway noise reduction in our country. But the noise barrier for high speed railway has weak point in low frequencies about 315Hz band. In this study, For developing of Interference-type Noise Reduction Device(INRD), acoustic analysis were performed using commercial software. For verifying the improvement in the noise reduction, noise measurement before and after installing of INRD were performed in Anechoic Chamber. From these acoustic analysis and noise measurement, it was known that developed INRD has a good noise reduction performance and can be used efficiently with conventional noise barrier.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.6
• /
• pp.495-501
• /
• 2013

This paper deals with noise reduction on a light source driving board in a projector. We analyze causes of noise/vibration in the circuit with the present increasing use of LD and LED driving boards. The main source of noise is the MLCC in the driving board. Our aim is to investigate how the mechanical arrangement of the circuit elements affects noise reduction. The result of our experiment shows that noise can be reduced by symmetrical arrangement and slots in PCB. This result is expected to facilitate a variety of applications for manufactures without a need to change circuit elements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.767-770
• /
• 2002

Reduction of the propagation noise generated during pass-by of KTX by noise barrier was measured and analysed for the two kinds of top-shaped noise reduction devices; one as a plywood board and the other as a PVC pipe were placed periodically. The height and length of reference noise barrier are 2.4 m and 50 m, respectively. The noise reduction with and without noise reduction devices was investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.625-629
• /
• 2014

For the purpose of the acoustic performance evaluation of noise reduction device(NRD) installed at the top of noise barrier for further decreasing of noise level of 400km/h class high-speed railroad(HEMU), the acoustic performance test method using speaker instead of really running railway vehicle was suggested in this paper. For this, noise source location and frequency spectrum of HEMU was analyzed through the field noise test. These data were used for the determination of speaker's installation positions and frequency correction values applied to the speaker noise source. And, 400 meters long NRD was installed at the site where HEMU will be running at a speed of 400km/h. Finally, the outdoor speaker test with and without NRD showed that this NRD could decrease noise level even more than 3dB(A). In the future, the acoustic performance results of NRD conducted with speaker test will be compared with that of field test for HEMU running at a speed of 400km/h.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.134-139
• /
• 2002

We have made known the study of shape development of interference device for vehicle noise control. It's primary object greatly attenuate the noise due to transport vehicle by small products installed on the noise barrier edge. Also, it is able to improve the insertion loss of a noise barrier without increasing the height. The present time, we set up a newly manufactured products on the noise barrier edge and testify to it's the performance make use of an experiment and evaluation for the reduction of highway traffic noise. In this paper the frequency characteristic of interference device of noise barriers with attached newly developed products in terms of shape, absorptive material and split panel, are examined using field test at highway.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.376.1-376
• /
• 2002

Reduction of the propagation noise generated during pass-by of KTX by noise barrier was measured and analysed fur the two kinds of top-shaped noise reduction devices; one as a plywood board and the other as a PVC pipe were placed periodically. The height and length of reference noise barrier are 2.4 m and 50 m, respectively. The noise reduction with and without noise reduction devices was investigated. (omitted)

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.12
• /
• pp.679-684
• /
• 2017

Recently, the speed of high-speed railway has been rapidly increase with the development of high-speed train design and operating technology. This causes a lot of complaints related the environmental noise in residential areas near the high-speed railway. In order to operate the high-speed railway in accordance with the design speed, noise reduction technology should be developed to meet the noise characteristics of high-speed railway. And it is important to develop the prediction technology by grasping the noise radiation characteristics. In order to meet these requirements, in recent years, infra-research for 400 km/h high speed railway has been conducted. Reliable noise prediction and noise reduction techniques have been developed through this study. This paper is concerned with wind pressure safety and noise performance evaluation of the newly developed 400 km/h noise reduction device. The wind pressure safety and The noise performance of the developed device was confirmed by this paper.

• Proceedings of the KSR Conference
• /
• 2002.05a
• /
• pp.577-583
• /
• 2002

We have made known the study of shape development of interference device for vehicle noise control. It's primary object greatly attenuate the noise due to transport vehicle by small products installed on the noise barrier edge. Also, it is able to improve the insertion loss of a noise barrier without increasing the height of noise barrier. The present time, we set up a newly manufactured products on the noise barrier edge and testify to it's the performance use of an experiment and evaluation for the reduction of railway noise. In this paper the frequency characteristic of interference device of noise barriers with attached newly developed products in terms of shape, absorptive material and split panel, are examined using field test around of railroad.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.6 s.123
• /
• pp.477-483
• /
• 2007

Major noise source in high speed rotating optical disk drives (CD and DVD-ROM) arises due to the high-speed airflow produced from the upper and lower surfaces on the rotating disk. The present paper deals with the experimental approach how to identify the noise source based on the fundamental principles of aeroacoustics and to propose a reduction method of the noise source. The CD-ROM device is composed of disk, window tray, motors at the bottom place and electronic circuit plate also located below the window plate. The window is cut in the tray to read the disk information using the optical device located below the tray and moving linearly from the center of the disk through the end of the disk. All components are possible noise generators. Experimental studies were carried out in the anechoic room with various design modifications, such as tray geometry, window size and hole location on tray, to identify the major aerodynamic noise source and significant reductions of the aerodynamic noise were obtained.