• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.617-635
• /
• 2020

The purpose of this study is to discuss how to improve the maneuverability of lifting and diving for underwater vehicle's vertical motion. Therefore, to solve these problems, applied the 3-D numerical simulation, Taguchi's Design of Experiment (DOE), and intelligent parameter design methods, etc. We planned four steps as follows: firstly, we applied the 2-D flow simulation with NACA series, and then through the Taguchi's dynamic method to analyze the sensitivity (β). Secondly, take the data of pitching torque and total resistance from the Taguchi orthogonal array (L9), the ignal-to-noise ratio (SNR), and analysis each factorial contribution by ANOVA. Thirdly, used Radial Basis Function Network (RBFN) method to train the non-linear meta-modeling and found out the best factorial combination by Particle Swarm Optimization (PSO) and Weighted Percentage Reduction of Quality Loss (WPRQL). Finally, the application of the above methods gives the global optimum for multi-quality characteristics and the robust design configuration, including L/D is 9.4:1, the foreplane on the hull (Bow-2), and position of the sail is 0.25 Ls from the bow. The result shows that the total quality is improved by 86.03% in comparison with the original design.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.12
• /
• pp.1293-1303
• /
• 2006

This paper represents a comparison the difference between existence and nonexistence of soundproof trees for road traffic noise. Also we suggested that the simple equation has been derived using a single regression analysis for predicting levels of $Leq_{th}$ at a given distance from a road in terms of the flow rate, the mean speed of the traffic, and the percentage of the type vehicles in the existence and nonexistence of soundproof trees. We classified a vehicle into four and analyzed contribution rate to traffic volume. As a result, the order showed as followed: light vehicle>medium vehicle>heavy vehicle>motorcycle. However, the results of analyzing contribution rate with between traffic volume and traffic noise by the each type showed as followed; Motorcycle>Light vehicle>Medium vehicle>Heavy vehicle. This study showed that the most a lof of traffic volumes of the three vehicles(light vehicle, medium vehicle and motorcycle) and heavy vehicle were existed in 67 km/h and 61 km/h of car speed, respectively. The total traffic noise to the mean car speed decreased because of the inflow a lot of traffic volumes between 2016 and 2388 in the range of 67 km/h of light vehicle speed, in traffic composition of 4.75% heavy vehicles, and 1.11% motorcycle. the final result for this study showed that statistical paired t-test for between existence and nonexistence of soundproof trees was significant(p<0.05) and the difference between daytime and night in the location of the nonexistence of plant communities with the independent sample T-test was significant(p<0.05). However, the independent sample T-test for analyzing the variance of traffic noise between daytime and night was not significant(p>0.05).

• Proceedings of the Safety Management and Science Conference
• /
• 2005.11a
• /
• pp.300-310
• /
• 2005

Mahalanobis Taguchi System (MTS) is developed by Genishi Taguchi as a part of his quality engineering methodology. The basic idea of Taguchi's quality engineering is looking for the way of effectiveness of analyzing multivariate system. In the MTS, with the standardized variables of healthy normal data, Mahalanobis Distance(MD) calculated and that can be discriminate between normal and abnormal objects. If this discrimination process is successful, next step is optimization which is try to reduce number of attributes by neglecting less effective attributes to MD. Orthogonal Array (OA) and Signal to Noise ratio (S/N) are used to evaluate the amount contribution of each attribute to the MD. Wisconsin Breast Cancer study, from machining learning repository at University of California at Irvine, used for examining the discriminant ability of MTS.

• The Journal of the Acoustical Society of Korea
• /
• v.4 no.3
• /
• pp.21-32
• /
• 1985

서로 상관관계가 있는 다입력원 진동계의 진동원을 규명하기 위한 방법을 제안하였다. 다차원 스펙트럼 해석을 이용함으로써 지하철 진동의 가장 중요한 진동원을 발견하였다. 이 분석은 진동의 전 달경로가 매우 복잡할 때 다입력-단일출력으로 모델화 하여 분석하는 방법이다. 또한 레지듀 스펙트럼 분석과 부분기여함수의 개념을 적용하여 지하철 진동이 콘크리트 구조물의 진동에 미치는 영향을 마이 크로 컴퓨터로 계산하였다. 이러한 연구의 결과로 지하철 진동의 다차원 스펙트럼의 오버올레벨을 측정 치와 비교하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.12
• /
• pp.1045-1055
• /
• 2013

It is true that the dependency on import is currently high in case of the safety checkup system of domestic airplanes, and it is at the point of time that localization of HUMS for small airplanes is required. In this study, the design factors were selected for the lightweight of HUMS for small airplanes by using Pro-Engineer which is a design tool and Abaqus. 9 models were made through experiment plans with Taguchi method for this, and the each model for weight lightening was selected through vibration analysis and shock analysis while in operation with experiment profile values. After fabricating HUMS, it was verified that as a result of experiment with the same profile values as the analysis, there was similarity between the analyzed values and values of the experiment. As a result of performing weight lightening which is the purpose of the study, electronic performance for small airplanes is assured and a design plan reducing 15 % weight compared to the targeted weight was deduced. Besides, it could be verified that the light weight model satisfied the maximum allowable displacement value of PCB[printed circuit board] and accordingly satisfied electronic properties of HUMS. In this study, the reliability of a product was certified through the result of an experiment on ground. If the reliability of HUMS were verified through a test flight in the future, it is considered that it would make a big contribution to localization of aerospace electronic equipment.

• Journal of Environmental Science International
• /
• v.16 no.10
• /
• pp.1179-1187
• /
• 2007

This paper represents the statistical characteristics of sources and receptors for road traffic noise in apartment complex. Also we suggested that the site-specific characteristics of vertical and horizontal distributions in the complex apartment have been derived using a different analysis for evaluating levels of Leq1h by the apartment floor at a given distance from a road in terms of the flow rate, the mean speed of the traffic, and the percentage of the type vehicles in the day and night periods. As a result, the contribution orders of traffic quantity by the type of vehicles showed as followed: light vehicle>medium vehicle>heavy vehicle>motorcycle. Especially, the mixing ratio of entering the road on the heavy vehicle in the daytime was two times higher than that of in the night. The speed in all types of vehicle is in the range of 41 and 81 km/hr and noise level was not significantly different in day and night-time. The sources of road traffic noise had different variations and uncertainties using a random variable and probability distribution. The sound distribution to receptors by the apartment floor showed S curve between 1st floor and $15^{th}$ floor With the normality test, the normal distributions using Anderson-Darling Test followed $1^{st},\;3^{th},\;13^{th}$ and $15^{th}$, floor in the daytime and all floors except $7^{th}$ floor in the night (p>0.05). And also, the value of the pearson correlation coefficient (r) obtained in this study have significantly different at the range of floor. In conclusion, the results suggested that the distribution characteristics of levels of $Leq_{1h}$ on the sources and receptors of road traffic noise in apartment complex must be improved and developed on the guideline of regulation of road traffic noise.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.769-777
• /
• 1999

Research on vibration of a vehicle with a transversely mounted 4-cylinder engine was performed using a vector synthesis method, Data of the engine vibration for the vector synthesis method was obtained experimentally and the data was ODS-fitted to calculate vibration level on any engine location assuming that the engine is rigid body in the frequency range of interest. In order to derive the excitation force on the vehicle body, the displacements were converted from the acceleration of engine. The transfer functions from engine mounts to toe pan on the floor were obtained experimentally. The vibration level on the toe pan was predicted by multiplying the excitation force by the transfer function. The predicted vibration level was compared with experimental data and the result was reasonable. Using the developed method, analysis was made for the effect of body fixture conditions of the vehicle when testing the engine vibration and for the effect of the transfer functions when the engine is installed or when the engine is removed. Finally the degree of contribution for 12 transfer paths was calculated.

• Journal of Navigation and Port Research
• /
• v.43 no.2
• /
• pp.110-121
• /
• 2019

Ports play a key role in international trade, as integral hubs where passengers and cargoes are loaded, discharged, and transshipped. However, the function of ports is becoming more diversified, expanding on roles as industrial clusters, as well as logistical centers. Such roles combined, reap numerous and significant benefits, mainly with growth of jobs and wealth creation, for the local population living in the city, and beyond. Citizens' awareness of the function and value of ports may not be positive, because of a range of negative factors such as emissions, noise, and road congestion, which can influence their perception. This study's contribution focuses on empirically evaluating the perception of Busan citizens of the local port, by applying Q methodology. The links connecting the port-city and local population, are assessed by identifying: 1) The level of awareness of the Busan citizens of the port; 2) Factors perceived as positive as well as factors perceived as negative by Busan citizens. There are four main factors, derived from the analysis: 1) Port functional knowledge; 2) Lack of social connectedness port-city; 3) Environmentally concerned and; 4) Absent port's ripple's effect. Policy recommendations suggest focusing on improving citizens' perception of the port, for each of the four main factors derived from the analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.651-658
• /
• 2014

Notification 2013-611 of MOLIT has come into effect. It relates primarily to new standard impact source. In this study, an in-depth experimental analysis of the difference between a bang machine and an impact ball was performed via field testing of shear wall and flat plate structure at 51 sites. This paper focuses on the difference in single number quantities between a bang machine and an impact ball. At wall thicknesses of 180 and 210 mm in shear wall structure, the single number quantities exhibited differences of 3.1 and 4.5 dB, respectively, and at thicknesses exceeding 250 mm in flat plate structure, the difference was constant at 4.6 dB. With regard to flat plate structures, the single-index difference increased up to 11 dB as the thickness of the floor slab increased. In general, the highest level of contribution for the bang machine was 63 Hz, irrespective of thickness determining bandwidth. The highest level for the impact ball were 63 Hz and 125 Hz. In future research, when reviewing additional field performance measurement data, it will be necessary to consider a detailed examination instead of the current method of uniformly adding 3 dB for all thicknesses and types of structures.

• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1093-1102
• /
• 1998

The success of controllability of smart structures depends on the quality of the bonding along the interface between the main structure and the attached sensing and acuating elements. Generally, the analysis procedures neglect the effect of the interfacial bond layer or assume that this bond layer behaves like viscoelastic material. Three different bond layers. two modified epoxy adhesives, and one isocyanate adhesive were prepared for their toughness and moduli. Bond layer of the chosen adhesive provides an almost perfect bonding condition between the composite structure and the PZT while bended significantly like arrow-shape. The perfect bonding condition is tested by considering various material properties of the bond layers. and based on this perfect bonding condition, the effects of the interfacial bond layer on the dynamic behavior and controllability of the test structure is experimentally studied. Once the perfect bonding condition is achieved. dynamic effects of the bond layer itself on the dynamic characteristics of the main structure is negligible. but the contribution of the attached PZT elements on the stiffness of the multi-layered structure becomes significant when the thickness of the bond layer increased.