• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.345-349
• /
• 2006

There has been an increasing demand for the mitigation of noise and vibration caused by KTX. One of considered noise reduction methods which is to enlarge mud-flap in gangway was selected and the replacement of all KTX mud-flaps by improved mud-flaps was completed recently. To investigate the noise characteristics of KTX with improved mud-flap, the measurement was performed. Based on the measurement results, the assessment of noise level, noise characteristics by speed and pure tone analysis for various track conditions was executed. It is shown that the use of improved mud-flap is effective to reduce the interior noise of KTX.

• KIEAE Journal
• /
• v.7 no.2
• /
• pp.57-62
• /
• 2007

Recently Among indoor noises plumbing noise from supply and drain water pipe is being pointed out as a annoying noise following to floor impact noise, and it is increasing the rate to point the noise due to the following several reasons: water pressure, vibration by fabricated structures and direct noise propagation from upper floor through ceiling This study aims to analyse the characteristics of toilet stool plumbing noise in apartment bathroom which are generated by crossing plumbings and elbows. And it analyse the effect of noise reduction by soundproofing and insulations which are covered at crossing plumbings. And also analyse the characteristics of noise about a type of elbows, crossing plumbing and result of dB(A). At last it provide a fundamental data for the purpose of reduction of plumbing noise in apartment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.445-448
• /
• 2001

Noise radiated from pile driving operation is one of major sources of community noise pollution and thus its operation method is strictly restricted by regulations. Although the drilling method is now used been commonly used in urban areas because of its activity, the benefit of low noise decreases due to high working cost. In the present work, noise characteristics of pile driving operation are carried out. Based on the study result, a low-noise pile cap for driven piles is developed in order to satisfy both the noise level restriction and the economical efficiency. Effects of pile cap are investigated by a scale model experiment, which is focused on the variation of impact force and sound pressure level. The results show a good possibility of noise reduction by an appropriately designed pile cap.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.337.1-337
• /
• 2002

In order to control the railway noise, the radiation characteristic of the noise during the train passage should be analyzed. Generally, the major noise sources for Korean Train Express are the rolling noise and power unit noise up to 300km/h. In this paper, we describe on a train model that is considered to be a row of point sources to calculate the radiation characteristic. The calculation results are compared with short distance measurement. (omitted)

• International Journal of Railway
• /
• v.4 no.3
• /
• pp.70-73
• /
• 2011

Controlling the exterior and interior noise emission has become an important issue in the research and development of high speed trains. As the operating speed of the train increases, the noise emission characteristics are expected to deviate from that of the existing trains due to several changes in the basic train layout. For train speed in excess of 350 km/h in particular, the aerodynamic noise component starts to exceed the structure-borne noise component, and even an incremental speed increase is accompanied by a rapid elevation in the noise level. The present study presents an engineering approach for predicting the aerodynamic noise level at the design stage for high speed trains. The experimental noise measurements from test run of Korean high speed train under development are presented as a partial validation of the proposed approach. While the overall aerodynamic noise can be cast in a single power law relationship against the train speed, different parts of the train show power law relationships unique to each component.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.476-481
• /
• 2013

Transfer path analysis(TPA) and operational deflection shape(ODS) have been widely utilized to analyze the characteristics of noise. TPA enables to decompose a noise into air-borne and structure-borne noises then estimate the path contribution of noise. ODS enables to analyze a moving shape and direction of interest components at a particular frequency. In this paper, TPA and ODS are applied to transfer paths of air-conditioner booming noise in a vehicle to reduce noise level, then a fixture is mounted it's path for distributing the high portion path contribution to the low portion path contribution. Through this experiment, the reduction of sound pressure level in air-conditioner booming noise is observed. Thereafter, TPA is again employed to verify the results of contribution.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1449-1452
• /
• 2006

When fluid at high speed flows over an open cavity, large acoustic pressure fields inside the cavity are produced by fluid/structure interactions at the downstream end of the cavity. The inter-coach spacing is one of the most important sources of the aero-acoustic noise of a high-speed train. This noise can usually be heard as low frequency structure-borne noise inside the train. In this study experiments were performed in order to investigate the effects of mud-flap length on the aeroacoustic noise generation inside high-speed trains. Results of the measurement confirmed that the characteristics of the noise generated from the inter-coach spacing are strongly dependent on the size of the gap. Also investigated are the characteristics of the turbulent flow after the inter-coach spacing and consequent generation of the aeroacoustic noise inside the cabin.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.3
• /
• pp.253-260
• /
• 2014

conducted. In-situ measurements were conducted to investigate the noise characteristics in high-speed trains such as KTX and KTX-Sancheon. Binaural microphones and spherical microphone were adopted to record and evaluate the spectral characteristics and noise incidence characteristics at the seats in the passenger cars. Environmental elements were also recorded during the noise measurements using a camcorder and GPS application. In addition, auditory tests were conducted to investigate annoyance of interior noise of high-speed trains. Based on the objective measure and subjective responses on interior noise, statistical analysis such as correlation and regression analyses were carried out. From the results perception models for evaluating the interior noise of high-speed train were derived.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.9 s.102
• /
• pp.1092-1099
• /
• 2005

This experimental study deals with the characteristics of LCD or PDP TV set noise, which are differ form those of CRT TV set. These characteristics are most important for establishing the effective method to reduce noise level, searching for the appropriate exposure level and evaluation method of LCD or PDP TV set noise. This study adopt two measurement method to specify the power level of LCD or PDP TV set noise in anechoic room(ISO 3741) and reverberation room(ISO 3745) . Comparing with each results of the two method, the reverberation room method is more simple in measuring and calculating the power level. And the subjective response test are carried out to select the pair of appropriate adjectives to present the characteristics of LCD or PDP TV set noise. The pair of 17 adjectives are selected from the 168 adjectives which are used in presenting the sound and noise form literature.

• Journal of the Korea Society of Computer and Information
• /
• v.23 no.12
• /
• pp.163-170
• /
• 2018

This study was conducted to investigate the effects of noise from dental clinics on workers and to establish a reduction plan. The noise generated by the treatment instrument(Ultrasonic scaler, Hand piece, 3-way syringe, Suction, Compressor) was measured in order to determine the characteristics(level, frequency) of the noise during medical treatment(Oral prophylaxis, Conservation treatment, Prosthesis treatment, Implant Scaling, Tooth eliminating). We also assessed the noise levels in dental clinic using evaluation indicators such as NR-curves and NRN. The results of the analysis showed that the noise generated during the treatment was 85dB(A) ~ 70dB(A) and that the high frequency component was dominant, which would affect the workers working at the dental clinic. The NR-curve analysis showed NR-67 to NR-83 and the high frequency components of 4kHz to 8kHz were predominant and far exceeded noise levels in the workplace. To minimize the noise damage of workers and to provide high quality medical service, it is necessary to establish countermeasures such as wearing a soundproof and periodic hearing tests.