• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.109-112
• /
• 2005

Friction welding is welding method to use frictional heat of two material. A defect of friction welding is that create flash. The flash is part that must have cut after welding finished. But the welding part with flow gallery by friction welding can't cut flash. Therefore the welding part with flow gallery was designed with no effect in flow. In this research, decide the welding shape parameter of welding part with flow gallery and do friction welding analysis. In friction welding analysis, must input necessary S-S curve, friction coefficient by temperature change, upset pressure, RPM etc. According to analysis result, decided the optimal shape of welding part with no effect in flow.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.182-188
• /
• 1994

This expermintal study is intended to investigate he development of flank wear in turning os SUS304 which is used in industrial applications and is acknowledged as a machining difficult material. In cutting process, change of velocity, change of feed, and change of depth of cut were investigated about the effect of flank wear, and slenderness ratio is also investigated. The variations of unit cutting force with the change of rake angle and the change of uncut chip area are observed. The friction angles are calculated for the change friction force and observed. The friction angles are calculated for the change friction force and normal forcd on the different rake angles. From this experimental study, the following results can be said. 1. Under the high cutting speed condition, the flaank wear is affected by the feed and depth of cut, but the influence of feed and depth of cut to the flank wear is reduced when the velocity is low. 2. The smaller slenderness ratio is, the shorter the tool life results in high cutting speed, and the lower cutting speed is, the lower the effect of slenderness ratio to the flank wear is. 3. Using the characteristics of force-RMS, the flank wear of a tool can be detected. There are almost no differences between the RMS characteristics of cutting force and feed force.

• Journal of the Korean Dietetic Association
• /
• v.15 no.3
• /
• pp.262-277
• /
• 2009

Fresh-cut foods have been widely used in the school foodservice industry due to their convenience and saving effects of labor and working hours. This study evaluated the effectiveness of using fresh-cut foods in school foodservice with respect to cost efficiency, customer satisfaction, employee satisfaction, and productivity. First, in terms of cost efficiency, the cost of the fresh-cut food per meal price significantly increased by 2.6% via the new production plan. Meanwhile, the costs of labor and food wastes significantly decreased by 3.0% and 0.3%, respectively, after implementing the new plan. Second, customer satisfaction towards foodservice significantly increased, from 2.94 points prior to the new plan to 3.45 points. Third, foodservice productivity such as of the number of meals per full-time equivalent employee increased by 5.7 meals, from 143.0 meals to 148.7 meals after intervention. The productivity index of work hours for producing a meal also increased and was reflected by a work time reduction of 0.77 minutes, specifically from 4.25 minutes to 3.48 minutes. The labor cost per meal also decreased by 29.9 won, from 331.91 won to 301.97 won, but there was no significant difference. Through these results, we identified that using pre-process foods in school foodservice has positive effects on labor saving, customer satisfaction, and employee work satisfaction.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.22 no.2
• /
• pp.81-88
• /
• 2011

Objectives : This study examined the reliability and validity of the Korean version of Asperger Syndrome Diagnostic Scale (K-ASDS), to calculate the cut-off score in the diagnosis of Asperger syndrome. Further, we examined classification error rate when applying cut-off scores. Methods : One hundred sixty-seven children participated in this study, including 46 with Asperger syndrome, 26 with PDD or PDD NOS, 43 with ADHD, and 52 normal children. Results : An ANCOVA demonstrated no significant differences in the K-ASDS total score between the Asperger and the PDD & PDD NOS groups. However, these groups did show significantly higher scores than the ADHD and normal groups. Among the five subscales on the K-ASDS, the Asperger group obtained significantly higher scores on the language and cognition subscales than the PDD & PDD NOS groups. Two scales were found to be useful in distinguishing the Asperger group from the PDD & PDD NOS group through a discriminant analysis. According to an analysis of ROC curve, the cut-off score on the K-ASDS for the diagnosis of PDD including Asperger syndrome was 121. Conclusion : We discussed that K-ASDS has pretty limit.

• Journal of the Korean Society of Tobacco Science
• /
• v.21 no.2
• /
• pp.119-127
• /
• 1999

This study was conducted to evaluate the effect of cigarette papers, flax and wood, on the delivery of mainstream smoke. The main components of cigarette papers were cellulose, hemicellulose, lignin, and pectin. Lignin contents, known as precursor of smoke's phenolic compounds, of the flax and wood cigarette papers were 5.8% and 10.6%, respectively. The pyrolysis products of cigarette papers were similar by the profile of total ion chromatogram. But, the area % of some components, such as 1,3-cyclopentanedione, 3,5- dimethyl cyclopentane-1,2-dione, 2-hydroxy-3-methyl-2-cyclopentenone, dihydro-2(3H)-furanone, 3-methyl-2(5H)-fruanone, and 5-methyl-2-furaldehyde delivered through pyrolysis of the flax cigarette paper were higher than that of wood cigarette paper. Otherwise, the area % of some components, such as 2-methyl-cyclopentene-l-one), 2,3-butanedione, 2-cyclopentene-l-one, and 5-hydroxy-2-methyl-furaldehyde, 2-furaldehyde delivered through pyrolvsis of the wood cigarette paper were higher than that of flax cigarette paper. To identify the difference between two cigarette papers, we used the cigarette column filled with the cut cigarette paper instead of the cut tobacco leaf. The amounts of semi-volatile fraction delivered from flax cigarette paper was more than that of wood cigarette paper. But, by using the cut tobacco, there was no big difference of delivery amount between flax and wood cigarette papers. Also, aroma of TPM by collecting from brening cut tobacco wrapped in flax and wood papers showed a different pattern by the electonic nose system. Although the difference between two cigarette papers by using the cut tobacco was smaller than that of cut cigarette paper, this result indicated that the fax and wood had the different effects on the delivery of smoke components as shown in the sensory test results.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.14 no.4
• /
• pp.257-263
• /
• 1994

The experiment was canied out to investigate the effects of cutting frequencies (3, 4 and 5 cuts per year) in relation to fertilization of mineral nitrogen on crude protein yield and the contents of crude protein and acid detergent fibre in orchardgms(Dacty1is glomerata L.). Tne results are as follows : 1. The content of crude protein increased according to the increase in cutting frequency and showed the highest in the 1st cut in all treatments. At 4 and 5 cutting frequencies per year, the content of crude protein increased in a large extent according to the increased fertilization of mineral nitrogen. However at 3 cutting frequency, the content of cmde protein appeared higher for no application of mineral nitrogen than for the treatments with fertilization. 2. 'Ihe content of acid detergent fibre(ADF) was considerably reduced at 4 and 5 cutting frequencies and in all treatments, the lowest were recorded in the 1st cut or in the last cut. At 3, 4 and 5 cutting frequencies, the highest ADF were shown in the 2nd cut, 3rd cut and 3rd cut respectively. However, the general trend was that the content of ADF was greatly reduced according to increased level of mineral nitrogen fertilization. 3. The yeild of cmde protein was the highest at 5 cutting frequency(l.2 ton DMIha) and it indicated that the yield of cmde protein increased in accordance to the increase in fertilization of mineral nitrogen and cutting frequency. 4. In all treatments, positive correlation(p<0.001) between the yeilds of crude protein and annual dry matter yield appeared. Negative correIation(p

• Korean Journal of Medicinal Crop Science
• /
• v.23 no.5
• /
• pp.363-369
• /
• 2015

Background : Platycodon grandiflorum radix used as a therapeutic agent for lung and respiratory diseases in traditional Korean medicine. The saponin and sugar content in P. grandiflorum root is dependent on the drying temperature and method. In this study, we investigated saponins and antioxidant contents in dried P. grandiflorum roots either not cut or cut to different lengths. Methods and Results : P. grandiflorum roots were either cut to 0.5, 1.0 or 2.0 cm in length or left uncut. They were dried at $45^{\circ}C$ and the effect of antioxidant substances, antioxidant ability, and saponin content were investigated. P. grandiflorum roots rapidly dried out when cut to short lengths. The saponin contents (platycodin D, polygalacin D, and deapioplatycodin D) was highest in the uncut P. grandiflorum roots. When the cut lengths were long, the levels of polyphenolic compound increased. However, 2,2'-azinobis-3-ethylbenzo-thiazoline-6-sulfonic acid (ABTS) and 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging activities were higher in the samples cut to shorter lengths. Conclusions : These results suggested that the saponin and antioxidant content of P. grandiflorum roots could be maximized by controlling the drying rate of the roots via adjustments to the root cutting length.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.668-673
• /
• 1998

The specimen of current study has the same type with the 3-span slabs of Burns et al used in the study by Mojtahedi/Gamble, which laid a ground for the revision of the ACI318-77 code to the ACI 318-83 code. But those specimens was failed prematurely before it reached the ultimate strength which the specimen had. The reason is that bonded reinforcements were cut off where there is no need for the flexural reinforcement. As results. the slabs failed ultimately where the reinforcements was cut off. Thus, the tendon stresses of failure may have been much smaller than the values which culd reach if the bonded reinforcements were extended beyond the theoretical cut off points. On the based on the fact mentioned above. the specimens which had the same conditions as the specimens of Burns et al were used in the current study, but in which the reinforcements were distributed in a sequence for the reinforcements not to be cut anywhere in the 3-span. As a results, it was known that the current ACI code, revised by the result of Mojtahedi/Gamble's study, overestimated the effect of span/depth ratio on the members with high span/depth ratio. Thus it was concluded that the effect of span/depth ratio on the ultimate stress of unbonded tendon regulated by the current ACI code must be reconsidered and reevaluated.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.48 no.4
• /
• pp.744-755
• /
• 2024

This study analyzes the characteristics, product dimensions, and ease of haenyeo suits to inform their reproduction. Large, medium, and small haenyeo suits were collected from four manufacturers in Jeju, and their components, cut styles, product dimensions, and ease were analyzed. In the current haenyeo suit design, the upper suit has a collar and a crotch, while the lower suit has a high rise with a gusset. Additionally, there are darts behind the neck in the upper suit and behind the knees in the lower suit. Haenyeo suits have a three-dimensional shape that accommodates the postures needed for haenyeo's underwater activities. The upper suit is finished with a cuffed hem or an uncuffed side seam with a diagonal or stepped cut. The lower suit is cut and sewn with the waist and hem at right angles or with the hem diagonal to the waistline. Haenyeo suit dimensions vary between manufacturers, and the models' body dimensions show that there is little or no ease. In conclusion, haenyeo suit manufacturers currently use the same components; however, they differ in terms of cut styles, sewing methods, dimensions, and designs.

• Nuclear Engineering and Technology
• /
• v.24 no.1
• /
• pp.14-29
• /
• 1992

COMCAF, a computer code for the common-cause failure analysis, is developed to treat the common-cause failures in nuclear power plants. In the treatment of common-cause failures, the minimal cut sets of the system are obtained first without changing the fault-tree structure. The occurrence probabilities of the minimal cut sets are then calculated accounting for the common-cause failures among components in the same minimal cut set or in different minimal cut sets. The basic parameter model is used to model the common-cause failures between similar or identical components. For dissimilar components, the assumption of symmetry used in the basic parameter model is applied to the basic events affecting two or more components. The top event probability is evaluated using the inclusion-exclusion method. In addition to the common-cause failures of components in the same minimal cut sets, failures of components in the different minimal cut sets are also easily accounted for by this method. This study applied this common-cause failure analysis to the PWR auxiliary feedwater system. The results in the top event probability for the system are compared with those of no common-cause failures.