• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.49-55
• /
• 2023

Currently, the demand for green technologies toward a sustainable future is rapidly increasing due to growing concern over environmental issues. Methanol is biodegradable and can provide clean combustion to reduce sulfur oxide and nitrogen oxide emissions, and therefore it is a candidate fuel for marine engines. However, the effect of methanol on tribological characteristic degradation should be addressed for methanol-fueled engines. In this study, the methanol addition effects on tribological characteristic degradation is experimentally assessed using a pin-on-disk tribo-tester. Ni-based alloy is used as a target material due to its broad applicability as an engine component material. For a lubricant, engine oil with and without methanol are used. The tests are conducted for up to 10,000 cycles under boundary lubrication while the change in friction force is monitored. Additionally, the wear rate is determined based on laser scanning confocal microscope data. An additional test in which methanol is added at regular intervals is performed with an aim to directly observe its effect on friction. Overall, the friction coefficient increases slightly with increasing methanol concentration. Furthermore, the wear rate of the pin and disk increase significantly with methanol addition. The results also indicate that the friction increases instantaneously with methanol addition at the contacting interface. These findings may be useful for better understanding the methanol effect on the tribological characteristics of Ni-based alloys for methanol-fueled engines with improved performance.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.E
• /
• pp.39-46
• /
• 2000

Volatile Organic Compounds (VOCs) are considered as the precursors of atmospheric ozone and photochemical smog formation. In particular, chemical plants have produced a lot of VOCs and thus they have been forced to reduce or remove air emissions from the on-site chemical facilities. For the effective removal of VOCs produced in the chemical plants, the authors employed a titanium oxide(TiO$_2$) mediated photo-catalytic oxidation method. The initiation methods employed in this study to produce oxygen radicals for th photo-catalytic oxidation of the VOCs were Ultra-Violet(UV), Non-Thermal Plasma(NTS), and a combination of Uv and NTP. This study focused on a comparison of the removal efficiencies of VOCs as a function of the initiation method such as NTP and/or UV techniques. Removal efficiency change of VOCs as was investigated as a function of the wavelength of the UV lamp(254, 302, and 365 nm) and the degree of TiO$_2$ coating (10 and 30%). In this study, it was identified that removal efficiencies if the VOCs under the normal air environment were much better than those under the nitrogen gas environment containing small amount of oxygen. Removal efficiency by NTP technique was much better than the UV or the combination of UV and NTP techniques. In a comparison if UV wavelengths employed, it was found that shorter wavelength showed better removal efficiency, compared with longer ones. When the removal efficiencies of VOCs were compared in terms of the degree of TiO$_2$ coating, the higher TiO$_2$coating showed better removal efficiency that the lower TiO$_2$ coating

• Journal of Microbiology
• /
• v.44 no.6
• /
• pp.689-693
• /
• 2006

Pbh1, from the fission yeast Schizosaccharomyces pombe, is a baculoviral inhibitor of apoptosis (IAP) repeat (BIR) domain-containing protein. Its unique encoding gene was previously found to be regulated by nitric oxide and nitrogen starvation. In the current work, the Pbh1-lacZ fusion gene was used to elucidate the transcriptional regulation of the pbh1 gene under various carbon sources. When fermentable carbon sources, such as glucose (at a low concentration of 0.2 %), sucrose (2.0 %) and lactose (2.0 %), were the sole carbon source, the synthesis of $\beta$-galactosidase from the Pbh1-lacZ fusion gene was reasonably enhanced. However, the induction by these fermentable carbon sources was abolished in the Pap1-negative S. pombe cells, implying that this type of induction of the pbh1 gene is mediated by Pap1. Ethanol (2.0%), a nonfermentable carbon source, was also able to enhance the synthesis of $\beta$-galactosidase from the fusion gene in wild-type cells but not in Pap1-negative cells. The results indicate that the S. pombe pbh1 gene is up-regulated under metabolic oxidative stress in a Pap1-dependent manner.

• Korean Journal of Plant Resources
• /
• v.26 no.2
• /
• pp.227-233
• /
• 2013

This study was carried out to effects of Allium victorials extract on lowering lipid, anti-oxidation and concentration of inflammatory mediators in rats fed high oxidized fat. Concentration of free fatty acid(FFA), triglyceride(TG), total cholesterol and LDL-cholesterol in plasma decreased in the Allium victorials extract groups and plasma HDL-cholesterol concentration revealed a tendency to increase in Allium victorials extract groups. Concentration of total cholesterol and TG in liver showed a tendency to decrease in Allium victorials extract groups. Concentration of thiobarbituric acid(TBARS) in plasma and liver showed a lower values in Allium victorials extract groups than that of control group. Activities of glutathione peroxidase(GSH-Px), superoxide dismutase(SOD) and catalase(CAT) in liver showed a tendency to increase in Allium victorials extract groups. Concentration of nitrogen oxide(NO), ceruloplasmin and ${\alpha}1$-acid glycoprotein in plasma showed a lower values in Allium victorials extract groups than that of control group. These results indicate that the Allium victorials extract have an functional material for lowering lipid, anti-oxidation and anti-inflammatory effect.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.8
• /
• pp.1124-1130
• /
• 2014

The objective of this study was to determine the responses in the digestibility of dry matter (DM) and amino acid (AA) composition of ileal endogenous flow (IEF) of pigs (initial body weight, $69.1{\pm}6.46$ kg) fed N-free diets (NFD) formulated with different ratios of corn starch to dextrose. Fifteen pigs fitted with a T-cannula at the distal ileum were fed 5 diets according to a triplicated $5{\times}2$ incomplete Latin-square design. Each period consisted of a 5-d adjustment period and 2 d of ileal digesta collection for 12 h on each of d 6 and 7 and between each period, there was a 5-d recovery period to avoid abnormal weight loss. The ratios of corn starch to dextrose investigated were 0:879, 293:586, 586:293, 779:100, and 879:0 for diet numbers 1, 2, 3, 4 and 5, respectively, and chromic oxide (5 g/kg) was used as an indigestible index. Ileal DM digestibility was greater in Diet 1 than that in Diet 4 (89.5% vs 87.3%, p<0.01) but they were not different from Diet 2, 3, or 5. The IEF for most of indispensable AA were not different among diets with the exception of Met, in which a lack of corn starch or dextrose gave lower (p = 0.028) IEF of Met than diets containing corn starch and dextrose. Likewise, the dispensable AA and total AA in the IEF did not differ among diets. The respective IEF of AA (mg/kg of dry matter intake) in pigs fed Diets 1, 2, 3, 4, or 5 were 301, 434, 377, 477,or 365 for Lys, 61, 89, 71, 87, or 61 for Met, and 477, 590, 472, 520, or 436 for Thr. Proline was the most abundant AA in the IEF followed by Gly, Glu, and Asp and together accounted for approximately 50% of the total ileal AA flows of pigs fed NFD. In conclusion, the variation in proportion of corn starch and dextrose in a NFD does not largely affect estimates of IEF of N and AA for growing-finishing pigs.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.73-81
• /
• 2011

The performance of emission factor has been validated by comparison with on-road test data. Emission factor, which is a function of vehicle speed, has been acquired based on chassis dynamometer test with NIER driving pattern. Portable Emission Measurement System, PEMS has measured on-road emission. Test vehicle was operated on defined test routes under different driving conditions, and made ten trips along its route. Emission factors properly simulate on-road test result, although there is some drawback to consider variety of driving condition on real world. Vehicle specific power and acceleration have been used to explain the distributed on-road result within same vehicle speed range. The trend in carbon dioxide and nitrogen oxide emission with respect to specific power and acceleration is clear. It has been found that specific power is a good explanatory variable for microscopic analysis for modal test result. Acceleration is good for microscopic as well as macroscopic analysis.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.11
• /
• pp.1653-1668
• /
• 2005

Assembly of hybrid mesophases through the combination of amphiphilic block copolymers, acting as structuredirecting agents, and silicon sources using low acid catalyst concentration regimes is a versatile strategy to produce large quantities of high-quality ordered large-pore mesoporous silicas in a very reproducible manner. Controlling structural and textural properties is proven to be straightforward at low HCl concentrations with the adjustment of synthesis gel composition and the option of adding co-structure-directing molecules. In this account, we illustrate how various types of large-pore mesoporous silica can easily be prepared in high phase purity with tailored pore dimensions and tailored level of framework interconnectivity. Silica mesophases with two-dimensional hexagonal (p6mm) and three-dimensional cubi (Fm$\overline{3}$m, Im$\overline{3}$m and Ia$\overline{3}$d) symmetries are generated in aqueous solution by employing HCl concentrations in the range of 0.1−0.5 M and polyalkylene oxide-based triblock copolymers such as Pluronic P123 $(EO_{20}-PO_{70}-EO_{20})$ and Pluronic F127 $(EO_{106}-PO_{70}-EO_{106})$. Characterizations by powder X-ray diffraction, nitrogen physisorption, and transmission electron microscopy show that the mesoporous materials all possess high specific surface areas, high pore volumes and readily tunable pore diameters in narrow distribution of sizes ranging from 4 to 12 nm. Furthermore, we discuss our recent advances achieved in order to extend widely the phase domains in which single mesostructures are formed. Emphasis is put on the first synthetic product phase diagrams obtained in $SiO_2$-triblock copolymer-BuOH-$H_2O$ systems, with tuning amounts of butanol and silica source correspondingly. It is expected that the extended phase domains will allow designed synthesis of mesoporous silicas with targeted characteristics, offering vast prospects for future applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.430.1-430.1
• /
• 2016

We present the concept of reducible fugitive material that conformally surrounds core Cu nanowire (NW) to fabricate transparent conducting electrode (TCE). Reducing atmosphere can corrodes/erodes the underlying/surrounding layers and might cause undesirable reactions such impurity doing and contamination, so that hydrogen-/forming gas based annealing is impractical to make device. In this regards, we introduce novel reducible shell conformally surrounding indivial CuNW to provide a protection against the oxidation when exposed to both air and solvent. Uniform copper lactate shell formation is readily achievable by injecting lactic acid to the CuNW dispersion as the acid reacts with the surface oxide/hydroxide or pure copper. Cu lactate shell prevents the core CuNW from the oxidation during the storage and/or film formation, so that the core-shell CuNW maintains without signficant oxidation for long time. Upon simple thermal annealing under vacuum or in nitrogen atmosphere, the Cu lactate shell is easily decomposed to pure Cu, providing an effective way to produce pure CuNW network TCE with typically sheet resistance of $19.8{\Omega}/sq$ and optical transmittance of 85.5% at 550 nm. Our reducible copper lactate core-shell Cu nanowires have the great advantage in fabrication of device such as composite transparent electrodes or solar cells.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.5
• /
• pp.625-632
• /
• 2004

Perfluorocompounds ($PFC_s$), such as tetrafluoromethane ($CF_4$) and hexafluoroethane ($C_2F_6$), have been widely used as plasma etching and chemical vapor deposition (CVD) gases for semiconductor manufacturing processes. Since these $PFC_s$ are known to cause a greenhouse effect intensively, there has been a growing interest in reducing $PFC_s$ emissions. Among various $CF_4$ decomposing techniques, a dielectric barrier discharge (DBD) is considered as one of a promising candidate because it has been successfully used for generating ozone ($O_3$) and decomposing nitrogen oxide (NO). Firstly, optimal concentration of oxygen for $CF_4$ decomposition was found to figure out how many primary and secondary reactions are associated with DBD process. Secondary, to find effective discharge method for $CF_4$ decomposition, a streamer and a glow mode in DBD are experimentally compared, which includes (i) coaxialcylinder DBD, (ii) DBD reactor packed with glass beads. and (iii) a glow mode operation with a helium gas. The test results showed that optimal concentration of oxygen was ranged 500 ppm~1% for treating 500 ppm of $CF_4$ and helium glow discharge was the most efficient one to decompose $CF_4$.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.5
• /
• pp.615-623
• /
• 2004

This study was conducted for developing the emission factors of nitrogen oxide(NOx) and carbon monoxide (CO) from the combustion boilers burning liquefied natural gas (LNG). These emission factors were compared with those of U.S. EPA and European Environment Agency (EEA). NOx and CO concentration in the flow gas were measured using Kane-May, KM9106 and Thermo Environmental Instruments Inc., 42C-HL. Measurement were conducted at thirty industrial and commercial LNG boilers. Emission factors were calculated on the basis of fuel consumption (kg-pollutant/㎥-fuel burned). NOx concentration at industrial boiler was 14~125 ppm and it was measured as 35~125 ppm at commercial boiler. NOx emission factors of industrial boiler and commercial boiler were 1.84kg/$m^3$ and 2.09kg/$m^3$, respectively. NOx emission factor of commercial boiler was higher than that of industrial boiler. The NOx emission factors estimated in this study were lower than those of U.S. EPA and higher than those of EEA. Average CO emission factor of industrial boiler was 0.65 kg/$m^3$ and at commercial boiler it was 0.70kg/$m^3$, CO emission factor at industrial boiler was lower than that at commercial boiler.