• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2357-2362
• /
• 2008

LHP is different from a conventional heat pipes in design and heat and fluid flow passages. The situations of the former is much complex than the latter. In LHPs, evaporation occurs at the contact interface between the heating plate and the porous wick, so some micro channels machined at the contact interface serve to let the vapor flow out of the evaporator. This complexity of contact geometry was known to cause a high resistance to heat flow. The present work was to study the problem of heat passage across the contact surface for LHPs and determine those values contact resistance. For two cases of contact structures, the thermal contact resistances were examined experimentally, one being obtained through mechanical contact under pressure and the other through sintered bonding. Nickel powder wick and copper plate were used for specimens. The result showed that a substantial reduction of contact resistance of an order of degree could be obtainable by sintered bonding.

• Journal of the Korean Chemical Society
• /
• v.10 no.4
• /
• pp.175-180
• /
• 1966

The electrode reduction velocity constants of Calcium, Nickel and Manganese (Zinc) ions in various supporting electrolyte solutions and temperatures were measured by polarography. The rate constants of those ions calculated by Delahay's graphimetric method and Koutecky's method were matched in 50% of experimental error. This error would be accountable because of the application of thier approximate method. But there are magnificent differences between those values and Randles and Sentioomerton's. We, also, have attempted to deduce the simplified relation between velocity constant and electrocappilary characteristics, computing the velocity constant simply and rapidly, on which Kambara, lshii and Imai, Adachi had studied and established thier related equations using parameter x, y and z, for some limited range of x. And we have extended the equation to the wider range of y value than they did for the above mentioned ions.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.3
• /
• pp.202-208
• /
• 2022

Pt-Ni nanocatalysts were loaded on carbon black by spontaneous reduction reaction of platinum (II) acetylacetonate and nickel (II) acetylacetonate, and they were characterized by transmission electron microscopy (TEM), thermogravimetric analyzer (TGA), energy dispersive x-ray analyzer (EDS), BET surface area and fuel cell test station. The distribution of the Pt and Ni nanoparticles was observed by TEM, and the loading weight of Pt-Ni nanocatalysts on the carbon black was measured by TGA. The elemental ratio of Pt and Ni was estimated by EDS. It was found that the loading weight of Pt-Ni nanoparticles was 5.54 wt%, and the elemental ratio of Pt and Ni was 0.48:0.35. Specific surface area was measured by BET analysis instrument and I-V characteristics were estimated.

• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.2
• /
• pp.185-194
• /
• 2024

Fe-Ni nanocatalysts loaded on carbon black were prepared via spontaneous reduction reaction of iron (II) acetylacetonate and nickel (II) acetylacetonate in dry process. Their morphology and elemental analysis were characterized by scanning electron microscopy, transmission electron microscopy (TEM), and energy dispersive X-ray analyzer. The loading weight of the nanocatalysts was measured by thermogravimetric analyze and the surface area was measured by BET analysis. TEM observation showed that Fe and Ni nanoparticles was well dispersed on the carbon black and their average particle size was 4.82 nm. The loading weight of Fe-Ni nanocatalysts on the carbon black was 6.83-7.32 wt%, and the value increased with increasing iron (II) acetylacetonate content. As the Fe-Ni loading weight increased, the specific surface area decreased significantly by more than 50%, because Fe-Ni nanoparticles block the micropores of carbon black. I-V characteristics showed that water electrolysis performance increased with increasing Ni nanocatalyst content.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.5
• /
• pp.246-250
• /
• 2009

The Ni formation behavior from the reduction of NiO nano crystals in the $H_2/N_2$ gas mixtures. The NiO nano crystals were synthesized by heat-treating nickel nitrate$(Ni(NO_3)_2\cdot6H_O)$ in the air at $500^{\circ}C$, and had an octahedral shape and the particle size of 200~500 nm. The NiO nano-crystals had well-developed (111) planes which is hardly formed in normal synthetic conditions. The reduction process was carried out at 300 and $600^{\circ}C$ for 15 and 60 minutes, respectively. When the NiO nano-crystals were reduced at $300^{\circ}C$, the Ni particles sustained the same octahedral shape as NiO, while Ni particles were to agglomerate at $600^{\circ}C$.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1995.11a
• /
• pp.25-25
• /
• 1995

Liquid phase sintering of 90W-6Ni-4Mn alloy has been investigated as functions of sintering atmosphere, heating rate, and reduction temperature. The present work accounts for the thermodynamic oxidatiodreduction reactions of constituent powders of W, Ni and Mn. By discounting these reactions, the previous investigations would obtain only the alloy with large pores and the lowered relative sintered density, by the liquid phase sintering under a dry hydrogen atmosphere. the sintering cycle consisted of a rapid heating to reduction temperatures under high purity nitrogen atmosphere, and holding for 4 hours and sintering at $1260^{\circ}C$ for 1 hour under a dry hydrogen gas. The relative density of the sintered alloy increased with increasing heating rate. As the reduction temperature increased, the relative density increased to the lm theotical density at the duction temture above $1150^{\circ}C$. The mimsturcatre of sintered alloys has been analysed by a scanning election microscope. The sintered density was compared with those obtained from the other investigators. It was found that the reduction $1150^{\circ}C$ results in the lowered densification of 90W-6Ni-4Mn alloy. This is caused by the fact that reducing reactions of W and Ni oxides contained in W an Ni powders concomitantly leads to oxidizing reaction of Mn powder the oxidized Mn is hardly reduced at sintering temperature and thereby remains large pores in the alloy. It is concluded that the W-Ni-Mn alloy with full density can be obtained by the precise control of atmosphere, heating rate, and sintering temperature.

• Korean Journal of Materials Research
• /
• v.26 no.2
• /
• pp.79-83
• /
• 2016

A commercial NiO (green nickel oxide, 86 wt% Ni) powder was reduced using a batch-type fluidized-bed reactor in a temperature range of 500 to $600^{\circ}C$ and in a residence time range of 5 to 90 min. The reduction rate increased with increases in temperature; however, agglomeration and sintering (sticking) of Ni particles noticeably took place at high temperatures above $600^{\circ}C$. An increasing tendency toward sticking was also observed at long residence times. In order to reduce the oxygen content in the powder to a level below 1% without any sticking problems, which can lead to defluidization, proper temperature and residence time for a stable fluidized-bed operation should be established. In this study, these values were found to be $550^{\circ}C$ and 60 min, respectively. Another important condition is the specific gas consumption rate, i.e. the volume amount ($Nm^3$) of hydrogen gas used to reduce 1 ton of Green NiO ore. The optimum gas consumption rate was found to be $5,000Nm^3/ton$-NiO for the complete reduction. The Avrami model was applied to this study; experimental data are most closely fitted with an exponent (m) of $0.6{\pm}0.01$ and with an overall rate constant (k) in the range of 0.35~0.45, depending on the temperature.

• Resources Recycling
• /
• v.22 no.4
• /
• pp.62-69
• /
• 2013

A study on the recovery of lithium and leaching behavior of NCM powder by carbon reduction for NCM-system Li-ion battery scraps was conducted. First of all, the oxide powders of NCM-system with layer structure were decomposed by carbon, lithium was converted to lithium carbonate by carbon reaction at above $600^{\circ}C$. The lithium carbonate powders with 99% purity were manufactured by washing method with water and concentration process for NCM powder after carbon reduction. The reaction yield was approximately 88% at $800^{\circ}C$ by carbon reduction. At this time, leaching efficiency at 2M sulfuric acid concentration was over 99% for cobalt, nickel and manganese.

• Restorative Dentistry and Endodontics
• /
• v.43 no.4
• /
• pp.46.1-46.10
• /
• 2018

Objectives: This study was to evaluate the antibacterial effect of different instrumentation and irrigation techniques using confocal laser scanning microscopy (CLSM) after root canal inoculation with Enterococcus faecalis (E. faecalis). Materials and Methods: Mesiobuccal and mesiolingual canals of extracted mandibular molars were apically enlarged up to a size 25 hand K-file, then autoclaved and inoculated with E. faecalis. The samples were randomly divided into 4 main groups according to the system of instrumentation and irrigation: an XP-endo Shaper (XPS) combined with conventional irrigation (XPS/C) or an XP-endo Finisher (XPF) (XPS/XPF), and iRaCe combined with conventional irrigation (iRaCe/C) or combined with an XPF (iRaCe/XPF). A middle-third sample was taken from each group, and then the bacterial reduction was evaluated using CLSM at a depth of $50{\mu}m$ inside the dentinal tubules. The ratio of red fluorescence (dead cells) to green-and-red fluorescence (live and dead cells) represented the percentage of bacterial reduction. The data were then statistically analyzed using the Kruskal-Wallis test for comparisons across the groups and the Dunn test was used for pairwise comparisons. Results: The instrumentation and irrigation techniques had a significant effect on bacterial reduction (p < 0.05). The iRaCe/XPF group showed the strongest effect, followed by the XPS/XPF and XPS/C group, while the iRaCe/C group had the weakest effect. Conclusions: Combining iRaCe with XPF improved its bacterial reduction effect, while combining XPS with XPF did not yield a significant improvement in its ability to reduce bacteria at a depth of $50{\mu}m$ in the dentinal tubules.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.1010-1017
• /
• 2011

The use of plated front contact for metallization of silicon solar cell may alternative technologies as a screen printed and silver paste contact. This technologies should allow the formation of contact with low contact resistivity a high line conductivity and also reduction of shading losses. A selective emitter structure with highly dopes regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing. When fabricated Ni/Cu plating metallization cell with a selective emitter structure, it has been shown that efficiencies of up to 18% have been achieved using this technology.