• 열처리공학회지
• /
• 제14권1호
• /
• pp.1-7
• /
• 2001

A method to simultaneously synthesize and consolidate the silicide $NiSi_2$ and the composite $NiSi_2$-20vol.%Nb from powders of Ni, Si, and Nb was investigated. Combustion synthesis was carried out under the combined effect of an electric field and mechanical pressure. The final density of the products increased nearly linearly with the applied pressure. Highly dense $NiSi_2$ and $NiSi_2$-20vol.%Nb with relative densities of up to 97% were produced under the simultaneous application of a 60MPa pressure and a 3000A current on the reactant powders. The respective Vickers microhardness values for these materials were 6.0 and 5.8 GPa. From indentation crack measurements, the fracture toughness values for $NiSi_2$ and $NiSi_2$-20vol.%Nb were calculated to be 3.3 and 4.7 $MPa{\cdot}m^{1/2}$, respectively.

• 한국결정성장학회지
• /
• 제12권2호
• /
• pp.73-79
• /
• 2002

코발트, 니켈, 구리 그리고 귀금속분말에 적용할 수 있는 polyol법은 균질한 크기와 형상을 갖는 금속분말합성에 매우 효과적인 공정이다 이 때 polyol은 용매, 환원제 그리고 보호제의 역학을 한다 $AgNO_3$글 촉매제로 첨가하여 비균질계 핵생성 반응을 야기할 경우 서브마이크폰 크기(0.5$\mu$m)의 코발트 분말을 한성학 수 있었다. 또한 촉매제인 Ag 핵의 수출 변화시키므로써 코발트 분말의 입도를 제어할 수 있음을 확인하였다.

• 한국분말재료학회지
• /
• 제27권1호
• /
• pp.1-7
• /
• 2020

In this research, a new medium-entropy alloy with an equiatomic composition of FeCuNi was designed using a phase diagram (CALPHAD) technique. The FeCuNi MEA was produced from pure iron, copper, and nickel powders through mechanical alloying. The alloy powders were consolidated via a high-pressure torsion process to obtain a rigid bulk specimen. Subsequently, annealing treatment at different conditions was conducted on the four turn HPT-processed specimen. The microstructural analysis indicates that an ultrafine-grained microstructure is achieved after post-HPT annealing, and microstructural evolutions at various stages of processing were consistent with the thermodynamic calculations. The results indicate that the post-HPT-annealed microstructure consists of a dual-phase structure with two FCC phases: one rich in Cu and the other rich in Fe and Ni. The kernel average misorientation value decreases with the increase in the annealing time and temperature, indicating the recovery of HPT-induced dislocations.

• 한국재료학회지
• /
• 제16권6호
• /
• pp.341-345
• /
• 2006

[ $Ni_2Si$ ] mixed powders were mechanically alloyed by a ball mill and then processed by hot isostatic pressing (HIP) and spark plasma sintering (SPS). In the powder that was mechanically alloyed for 15minutes(MA 15 min), only Ni and Si were observed but in the powder that was mechanically alloyed for 30minutes(MA 30 min), $Ni_2Si$, Ni and Si were mixed together. Some of the MA 15 min powder and MA 30 min powder were processed by HIP under pressure of 150MPa at the temperature of $1000^{\circ}C$ for two hours and some of them were processed by SPS under pressure of 60 MPa at the temperature of $1000^{\circ}C$ for 60 seconds. Both methods completely compounded the powders to $Ni_2Si$. The maximum density of sintered lumps by HIP method was 99.5% and the maximum density of the sintered lump by SPS method was 99.3%. with the hardness of HRc 66 with the hardness of HRc 63. Therefore, the SPS method that can sinter in short time at low cost is considered to be more economical that the HIP method that requires complicated sintering conditions and high cost and the sintering can produce target materials in desired sizes and shapes to be used for thin film.

• 한국수소및신에너지학회논문집
• /
• 제3권2호
• /
• pp.9-15
• /
• 1992

Electroless copper plating method using an alkaline bath have been employed in copper coating of the (LM)Ni4.5Co0.1MnO.2A10.2 hydrogen storage alloy powders for electrode preparation. The plating were conducted without any pretreatment of alloy powders. For the preparation of the electrodes, about 0.12g of the copper coated alloy powder (copper to alloy ratio 1/3 by weight) was compacted with pressure of 6 tons/cm2 at room temperature. The disk-type compacts had a diameter of 10mm and thickness of about 0.24mm. The electrode characteristics were examined through SEM observations and electrochemical measurements in a half cell. The electrochemical measurement showed that the maximum discharge capacity of the electrodes prepared by using alkaline bath were 245mAh per gram of coated alloy (327mAh per gram of alloy) and appeared a considerable degradation with increasing number of cycles. The decrease of the discharge capacity after 100 cycles was about 30% It can be suggested that, with a slight of improvement, this electroless copper plating method could be applied to the preparation of the rare earth-nickel based alloy electrode.

• 한국결정성장학회지
• /
• 제28권2호
• /
• pp.85-90
• /
• 2018

폐니켈수소전지에 함유되어 있는 희토류를 회수하기 위하여 $H_2SO_4$로 침출한 용액에 10 M NaOH를 첨가하여 희토류를 pH 2.0 이하에서 약 98 % 침전시켰다. 이후 회수된 희토류 복합 침전물은 $800^{\circ}C$에서 4시간 동안 열처리를 통해 $HNO_3$에 대한 침출률을 증가시켰으며, 희토류 복합 침전물이 용해된 용액에 oxalic acid를 첨가하여 2차 침전을 실시하였다. 재침전된 희토류는 다시 $800^{\circ}C$에서 4시간 열처리를 통해 산화물 형태로 변환되었으며, 이때 희토류 산화물의 순도는 약 99.5 %를 나타내었다.

• 한국자기학회지
• /
• 제9권2호
• /
• pp.78-84
• /
• 1999

고온연소합성법(self-propagating high temperature synthesis)을 이용하여(Ni, Zn)Fe2O4 분말을 제조하고 초기 분말의 크기와 산소압에 따른 생성물의 미세조직과 자기적 특성을 조사하였다. (Ni, Zn) 페라이트 분체는 다양한 입도의 Fe, Fe2O3, NiO, ZnO의 원료 분말을 n-hexane 용액에서 습식으로 spex mill을 사용하여 5분 혼합하고 12$0^{\circ}C$ 진공로에서 24시간 건조한 후 0.5~10기압의 산소압에서 고온연소합성 반응으로 제조하였다. 성형 압력이 없는 경우 평균 연소온도와 연소속도는 최대 약 125$0^{\circ}C$와 9.8mm/sec였으며 산소압과 ZnO입도가 감소하면 감소하였다. 고온연소합성된 시료는 다공질 구조를 갖고 있으며 X-선 회절 시험으로 시편들의 spinel구조를 관찰하였다. ZnO입도와 산소압이 증가하면 보자력, 최대자화, 잔류자화, 각형비 및 큐리 온도는 각각 13.24Oe, 43.88emu/g, 1.27emu/g, 0.0034emu/gOe, 37.8$^{\circ}C$에서 11.83Oe, 68.87emu/g, 1.23emu/g, 0.00280emu/gOe, 439.$^{\circ}C$와 7.99Oe, 75.84emu/g, 0.791emu/g, 0.001937emu/gOe, 53.8$^{\circ}C$로 변화하였다. 산소압에 따른 겉보기 활성화에너지를 고려하면 페라이트의 연소합성 반응은 ZnO입도와 산소압에 크게 의존한다.

• International Journal of Safety
• /
• 제1권1호
• /
• pp.58-61
• /
• 2002

A preparation method of cobalt supported alumina catalyst for a emergency escape mask cartridge has been studied. Catalysts were prepared by incipient wetness impregnation method using pre-shaped $\gamma$=alumina powders of 70-100 mesh. The catalyst was tested in a continuous-flow reactor system and characterized by elemental analysis, BET and TGA-DTA techniques. Cobalt shows higher activity than platinum or nickel for carbon monoxide oxidation at room temperature. Optimum loading amount of cobalt was 10 wt.% for CO oxidation and the reaction activity increases gradually with the increase of calcination temperature up to $450^{\circ}C.

• 한국결정학회지
• /
• 제12권1호
• /
• pp.20-24
• /
• 2001

NiZn-ferrite was synthesized usign waste iron oxide catalysts which were produced from styrene monomer process and buried underground as an industrial wastes. The spinel type ferrite was obtained by calcination and sintering of the mixture of finely ground waste catalysts, nickel oxide and zinc oxide powders. The sintered body of Ni/sub 0.5/Zn/sub 0.5/Fe₂O₄ composition at 1230℃ for 5 hours showed the density of 5.38g/㎤, and initial permeability of 59 at 1 kHz. Not only cerium oxide, which existed as a major component in the catalyst, but also unicorporated NiO and ZnO into spinel structure remained as second phases after sintering.

• Journal of Electrochemical Science and Technology
• /
• 제3권4호
• /
• pp.178-184
• /
• 2012

A porous nickel (P-Ni) substrate was prepared by selective leaching of zinc from pressed pellets containing powders of Ni & Zn in 4 M NaOH solution. Anodic deposition of manganese oxide onto the porous Ni substrate ($MnO_x$/P-Ni) formed nano-flakes of manganese oxide layers as revealed in SEM studies. Pseudocapacitance of this oxide electrode was evaluated by cyclic voltammetry (CV) and chronopotentiometry (CHP) in 2 M NaOH solution. The specific capacitance of the Mn oxide electrode was as high as 1515 F $g^{-1}$, which was ten times higher than Mn oxide deposited on a flat Ni-ribbon. 80% of capacity was retained after 200 charge/discharge cycles. The system showed no loss of activity in dry form over period of days. The impedance studies indicated highly conducting $MnO_x$/P-Ni substance and the obtained specific capacitance from impedance data showed good agreement with the charge/discharge measurements.