• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.2
• /
• pp.108-121
• /
• 2009

The suspended particulate matters have been collected on membrane filters and glass fiber filters by an 8-stage cascade impactor for 2 years (Sep. 2005${\sim}$Sep. 2007) in Kyung Hee University-Global Campus located on the border of Yongin and Suwon. The 20 chemical species (Al, Mn, Si, Fe, Cu, Pb, Cr, Ni, V, Cd, Ba, $Na^+$, ${NH_4}^+$, $K^+$, $Mg^{2+}$, $Ca^{2+}$, $Cl^-$, ${NO_3}^-$, and ${SO_4}^{2-}$) were analyzed by an ICP-AES and an IC after performing proper pre-treatments of each sample filter. Based on these chemical information, the PMF receptor model was applied to identify the source of ambient size-by-size particulate matters. The receptor modeling is the one of the statistical methods to achieve resonable air pollution management strategies. A total of 10 sources was identified in 9 size-ranges such as long-range transport, secondary aerosol, $NH_{4}NO_{3}$ related source, coal combustion, sea-salt, soil, oil combustion, auto emission, incineration, and biomass burning. Especially, the secondary aerosol source assorted in fine and coarse modes was intensively studied.

• Journal of Environmental Science International
• /
• v.17 no.10
• /
• pp.1147-1154
• /
• 2008

Road runoff, one of non-point source pollutants, contains various heavy metals, most of which flow into discharge waters without being treated. The mechanism of removing the heavy metals in water is similar to that of removing micro-particles. Therefore, it is considered that it is possible to remove a lot of the heavy metals contained in the road runoff by filtering or absorbing them. In this paper, performed has been a basic study on the characteristics of UNFS (Up Flow Non-Point Source Filtering System) using carbide pellet and zeolite pellet as double-layer filtering mediums to treat the road runoff. The removal rate with filtering and absorption time has been shown as follows: 29.0% for Cr; 27.8% for Cd; 25.7% for Fe; 25.4% for Co; 21.2% for Pb; ]9.6% for Zn; 18.2% for Al; 17.0% for Mn; 11.3% for Ni; 7.5% for Cu. The overall removal rate according to influx change has been shown to be approximately 30%, and the load of heavy metals flowing out in initial precipitation could be reduced by using carbide as a recycling filtering medium. When the removal as coarse particles settle is added up, it is expected that UNFS will result in a higher removal rate.

• The Korean Journal of Physiology
• /
• v.27 no.1
• /
• pp.107-114
• /
• 1993

Most of voltage operated $Ca^{2+}$ channels can be divided into three types (T-, N-, and L-type), according to the electrical and pharmacological properties. Their distribution is closely related to cell specific functions. Properties of the voltage activated $Ca^{2+}$ current in mouse eggs were examined to classify channel types and to deduce the function by using whole cell voltage clamp technique. $Ca^{2+}$ currents appeared below -40 mV and reached a maximum at -15 mV (half maximum was -31 mV), then decayed rapidly (inactivation time constant ${\tau}=28.2{\pm}9.59$ ms at -10 mV within 50 ms after the onset of step depolarization. Activation and inactivation of the $Ca^{2+}$ channel was steeply dependent on voltage, in a relatively low range of $-70\;mV{\sim}-10 mV,$ half maximum of activation was -31 mV and that of inactivation was -39 mV, respectively. This current was not decreased significantly by nifedipine, a specific dihydropyridine $Ca^{2+}$ channel blocker in the range of $1\;{\mu}M\;to\;100{\mu}M.$ The inhibitory effect of $Ni^{2+}\;on\;Ca^{2+}$ current was greater than that of $Cd^{2+}.$ The conductance of $Ba^{2+}$ through the channel was equal to or lower than that of $Ca^{2+}$ These results implied that $Ca^{2+}$ current activated at a lower voltage in the mouse egg is carried via a $Ca^{2+}$ channel with similar properties that of the T-type channel.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.413-422
• /
• 2011

A battery is an important part of the component, as a power source of the control of rolling stock at starting movement or emergency control. Now widely used batteries are Ni-Cd batteries and lead accumulators, and these are increasingly getting smaller and lighter. In addition, the electric capacity required is increasing, due to the development of electronic control technology of rolling stock. Therefore, various kinds of high-efficiency battery are considered for the new routes' rolling stock, but rolling stock's batteries should be fully tested to prove safety and also have no difficulty in terms of management, so because of the requirement, it is difficult to be in practical application. In this paper, we will survey cases of applying battery to rolling stock and then we will review whether there is any problem about safety and performance, management to discuss future trend of batteries.

• Spatial Information Research
• /
• v.20 no.4
• /
• pp.17-27
• /
• 2012

This study was performed to evaluate the spatial distribution of heavy metals using principal component analysis and Ordinary Kriging technique in the Gangwon Mine site. In the soils from the sub soil, the contents of Zn and Ni in the PC1 were gradually dispersed from south to north direction, while the components of Cd and Hg in the PC2 showed an increase significantly from middle-south area in the Gangwon Mine site. According to the cluster analysis, pollutant metals of As and Cu were presented a strong spatial autocorrelation structure in cluster D. The concentration of As was 0.83mg/kg and shown to increase from the south to north direction. The spatial distribution maps of the soil components using geostatistical method might be important in future soil remediation studies and help decision-makers assess the potential health risk affects of the abandoned mining sites.

• Journal of Soil and Groundwater Environment
• /
• v.18 no.1
• /
• pp.123-128
• /
• 2013

Water quality and contamination of sediment is a growing concern in the Iksan stream of Korea. Heavy metal contamination and changes in the physicochemical properties of the stream were evaluated. Water and sediment samples were collected from six sites during the dry and rainy seasons; pH, DO, EC, ORP, turbidity, $PO_4$-P, $NO_3$-N and selected heavy metals (Cu, Pb, Ni, As, Zn, Cd, Hg) were measured. Results showed almost no change in pH between seasons. DO was highest at site 2 (~2.63 mg/L) in the dry season; EC (1,540 ms/m) was greatest at site 1 in both seasons. The ORP gradually increased from the dry to rainy season at most of the sites and was highest at site 5. Turbidity was highest at site 1 and gradually decreased from the dry to rainy season at all sites except site 3. $PO_4$-P ranged from a high of 1,193mg/L at site 1 to in the dry season to a low of ~1.2 mg/L at site 4. In contrast, $NO_3$-N was highest at site 3 in the rainy season (12,531 mg/L). Among the heavy metals measured, Cu and Zn concentrations were highest at all sediment sites. Cu and Zn are added to livestock feed to improve reproductive rates and can be carried to the stream with manure. Transport of sediment and heavy metals during the rainy season is the major source of stream contamination and it is important to continue monitoring and take necessary action in these areas.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.126-126
• /
• 2017

본 연구는 가축분뇨를 퇴비화 하는 과정에서 흔히 사용되는 수분조절제인 톱밥, 왕겨 등의 가격적 부담으로 인해 좀 더 가격이 저렴한 수분조절제들의 성분을 비교 분석하여 어떤 차이가 있는지 확인하기 위하여 실시되었다. 이를 위해 6가지 수분조절제를 토대로 유도결합플라즈마분광계 장비를 이용하여 화학적 분석, 인장시험기를 이용하여 물리적 분석을 하였다. 화학적 분석을 통해 수분조절제 내 함유되어 있는 성분들을 분석하였으며 물리적 분석을 통해 중량, 함수율, 흡수율, 인장강도 등을 측정하였다. 화학적으로 분석을 했을 시 K, Cd, Pb, Ni, Zn, Cu, Cr, As 등을 측정을 하였으며 앞서 분석했던 각각의 성분들은 농촌진흥청에 명시되어 있는 유해성분의 최대량보다 대부분 적게 측정이 되었다. 물리적으로 분석을 했을 시, 각 수분조절제의 함수율은 최소 10.29%에서 최대 16.07%까지 측정이 되었다. 전단강도는 기존 상태가 가장 높게 측정이 되었으며 다음으로 건조상태 흡수상태로 측정이 되었다. 일반적으로 사용하기에는 흡수율이 가장 높은 우드 브리켓-1이 가장 적합한 것으로 판단된다.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.7
• /
• pp.135-147
• /
• 2015

Remediation of metal(loid)s-contaminated sites is crucial to protect human and ecosystem. Solidification and stabilization of metal(loid)s by the binder amendment is one of the cost-effective technologies. In this study, metal (loid)s in various field-contaminated soils obtained from steel-making, metal refinery and mining tillage were immobilized by the application of single binders such as diammonium phosphate (DAP), lime, and ladle slag. The efficiency of solidification and stabilization was evaluated by Toxicity Characteristic Leaching Procedure (TCLP) and the Standard, Measurements and Testing programme of European Union (SM&T) extraction processes. In terms of TCLP extraction, the binder was effective in order of lime > DAP > ladle slag. All binders were highly effective in the immobilization of Pb, Zn, Cu, Ni, and Cd. The increased immobilization efficiency is attributed to the increase in the Step III and IV fractions of the SM&T extraction. Lime and ladle slag were highly effective in the immobilization of the metal(loid)s, however, As release increased with DAP due to competition between the phosphate originated from DAP and arsenate. A further study is needed for the better immobilization of multi metal(loid)s using binary binders.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.245-245
• /
• 2015

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. 특히 CIGS 태양전지에서는 Na의 역할이 매우 중요한데 유연기판의 경우 이러한 Na이 없을 뿐만 아니라 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 또한 플라스틱기판의 경우 내열성이 낮아 저온에서 공정을 진행해야하는 단점이 있다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 유연기판으로 STS 430 stainless steel과 poly-imide를 이용하여 특성 개선을 진행하였다. 먼저 stainless steel과 Poly-imide, soda-lime glass, coning glass의 기판을 이용하여 기판에 따른 흡수층의 특성을 비교 분석하였으며 stainless steel 기판을 이용하여 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 이때 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.6%로 증가하였다. 또한 poly-imide 기판을 이용하여 $400^{\circ}C$이하에서 흡수층을 제조하여 특성평가를 진행하였으며 소자 제조 후 효율은 약 12.2%를 달성하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.86.2-86.2
• /
• 2015

Cu2ZnSn(S,Se)4 thin film solar cells have been fabricated using sputtered Cu/Sn/Zn metallic precursors on Mo coated sodalime glass substrate without using a toxic H2Se and H2S atmosphere. Cu/Sn/Zn metallic precursors with various thicknesses were prepared using DC magnetron sputtering process at room temperature. As-deposited metallic precursors were sulfo-selenized inside a graphite box containing S and Se pellets using rapid thermal processing furnace at various sulfur to selenium (S/Se) compositional ratio. Thin film solar cells were fabricated after sulfo-selenization process using a 65 nm CdS buffer, a 40 nm intrinsic ZnO, a 400 nm Al doped ZnO, and Al/Ni top metal contact. Effects of sulfur to selenium (S/Se) compositional ratio on the microstructure, crystallinity, electrical properties, and cell efficiencies have been studied using X-ray diffraction, Raman spectroscopy, field emission scanning electron microscope, I-V measurement system, solar simulator, quantum efficiency measurement system, and time resolved photoluminescence spectrometer. Our fabricated Cu2ZnSn(S,Se)4 thin film solar cell shows the best conversion efficiency of 9.24 % (Voc : 454.6 mV, Jsc : 32.14 mA/cm2, FF : 63.29 %, and active area : 0.433 cm2), which is the highest efficiency among Cu2ZnSn(S,Se)4 thin film solar cells prepared using sputter deposited metallic precursors and without using a toxic H2Se gas. Details about other experimental results will be discussed during the presentation.