• 한국전기전자재료학회논문지
• /
• 제16권4호
• /
• pp.280-285
• /
• 2003

The influence of silicon surface damage on nickel-silicide (NiSi) has been characterized and H$_2$ anneal and TiN rapping has been applied to suppress the electrical, morphological deterioration phenomenon incurred by the surface damage. The substrate surface is intentionally damaged using Ar IBE (Ion beam etching) which can Precisely control the etch depth. The sheet resistance of NiSi increased about 18% by the surface damage, which is proven to be mainly due to the reduced silicide thickness. It is shown that simultaneous application of H: anneal and TiN capping layer is highly effective in suppressing the surface damage effect.

• 대한금속재료학회지
• /
• 제46권11호
• /
• pp.762-769
• /
• 2008

Hydrogenated amorphous silicon(a-Si : H) layers, 120 nm and 50 nm in thickness, were deposited on 200 $nm-SiO_2$/single-Si substrates by inductively coupled plasma chemical vapor deposition(ICP-CVD). Subsequently, 30 nm-Ni layers were deposited by E-beam evaporation. Finally, 30 nm-Ni/120 nm a-Si : H/200 $nm-SiO_2$/single-Si and 30 nm-Ni/50 nm a-Si:H/200 $nm-SiO_2$/single-Si were prepared. The prepared samples were annealed by rapid thermal annealing(RTA) from $200^{\circ}C$ to $500^{\circ}C$ in $50^{\circ}C$ increments for 30 minute. A four-point tester, high resolution X-ray diffraction(HRXRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and scanning probe microscopy(SPM) were used to examine the sheet resistance, phase transformation, in-plane microstructure, cross-sectional microstructure, and surface roughness, respectively. The nickel silicide on the 120 nm a-Si:H substrate showed high sheet resistance($470{\Omega}/{\Box}$) at T(temperature) < $450^{\circ}C$ and low sheet resistance ($70{\Omega}/{\Box}$) at T > $450^{\circ}C$. The high and low resistive regions contained ${\zeta}-Ni_2Si$ and NiSi, respectively. In case of microstructure showed mixed phase of nickel silicide and a-Si:H on the residual a-Si:H layer at T < $450^{\circ}C$ but no mixed phase and a residual a-Si:H layer at T > $450^{\circ}C$. The surface roughness matched the phase transformation according to the silicidation temperature. The nickel silicide on the 50 nm a-Si:H substrate had high sheet resistance(${\sim}1k{\Omega}/{\Box}$) at T < $400^{\circ}C$ and low sheet resistance ($100{\Omega}/{\Box}$) at T > $400^{\circ}C$. This was attributed to the formation of ${\delta}-Ni_2Si$ at T > $400^{\circ}C$ regardless of the siliciation temperature. An examination of the microstructure showed a region of nickel silicide at T < $400^{\circ}C$ that consisted of a mixed phase of nickel silicide and a-Si:H without a residual a-Si:H layer. The region at T > $400^{\circ}C$ showed crystalline nickel silicide without a mixed phase. The surface roughness remained constant regardless of the silicidation temperature. Our results suggest that a 50 nm a-Si:H nickel silicide layer is advantageous of the active layer of a thin film transistor(TFT) when applying a nano-thick layer with a constant sheet resistance, surface roughness, and ${\delta}-Ni_2Si$ temperatures > $400^{\circ}C$.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.603-606
• /
• 2005

In this paper, the formation and thermal stability of Ni-silicide using Ni-Pd alloys is studied for ultra shallow S/D junction of nano-scale CMOSFETs. There are no different effects when Ni-Pd is used in single structure and TiN capping structure. But, in case of Cobalt interlayer structure, it was found that Pure Ni had lower sheet resistance than Ni-Pd, because of a thick silicide. Also, Ni-Pd has merits that surface of silicide and interface between silicide and silicon have a good morphology characteristics. As a result, Ni-Pd is an optimal candidate for shallow S/D junction when cobalt is used for thermal stability.

• 한국산학기술학회논문지
• /
• 제8권2호
• /
• pp.195-200
• /
• 2007

최소선폭 $0.1{\mu}m$ 이하의 살리사이드 공정을 상정하여 $10nm-Ni_{0.5}Co_{0.5}/70\;nm-Poly-Si/200\;nm-SiO_2$ 구조로부터 쾌속 열처리를 이용해서 실리사이드 온도를 $600{\sim}1100^{\circ}C$까지 변화시키면서 복합실리사이드를 제조하고 이들의 면저항의 변화와 미세구조의 변화를 면저항 측정기와 TEM 수직단면, 오제이 두께 분석으로 확인하였다. 기존의 동일한 공정으로 제조된 니켈실리사이드에 비해 제안된 니켈 코발트 복합실리사이드는 $900^{\circ}C$까지 저저항을 유지시킬 수 있는 장점이 있었고 20nm 두께의 균일한 실리사이드 층을 폴리실리콘 상부에 형성시킬 수 있었다. 고온 처리시에는 복합실리사이드와 실리콘의 전기적으로 상분리되는 혼합현상으로 고저항 특성이 나타나는 문제를 확인하였다. 제안된 NiCo 합금 박막을 70nm 높이의 폴리실리콘 게이트를 가진 디바이스에 $900^{\circ}C$이하의 실리사이드화 온도에서 효과적으로 산리사이드 공정의 적용이 기대되었다.

• 한국산학기술학회논문지
• /
• 제6권3호
• /
• pp.273-277
• /
• 2005

새로이 제안된 15nm-Ni/15nm-Co의 적층구조로부터 제조된 NiCo 복합실리사이드를 실제 디바이스에 채용하기 위해, $SiO_2$ 스페이서를 가진 폴리실리콘 게이트 선폭이 $0.25\~l.5um$까지 변화하는 테스트그룹을 이용하여 30초-RTA를 이용한 실리사이드화 온도를 $700^{\circ}C\~1100^{\circ}C$까지 변화시키면서 이때 cleaning전후의 잔류금속의 생성모습을 확인하였다. RTA온도가 올라갈수록 $SiO_2$로 구성된 필드와 스페이서 상부와, 실리사이드가 형성된 게이트 상부에 $0.25{\mu}m$정도의 단축직경을 가진 타원형 잔류금속이 미로형 또는 게이트 방향으로 생성되는 특징이 있었고 동시에 응집이 많아지는 현상이 있었다. 응집이 많을수록 하부 절연층과의 반응도가 증가하여 절연특성이 저하될 수 있었고 과도한 습식제거 공정을 오래하여야 하므로 실험범위 내에서 가급적 저온 실리사이드화 열처리가 바람직하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.3-4
• /
• 2006

In this paper, a nickel silicide technology with post-silicidation annealing effect for thin film SOI devices is investigated in detail. Although lower resistivity Ni silicide can be easily obtained at low forming temperature, poor thermal stability and changing of characteristic are serious problems during the post silicidation annealing like ILD (Inter Layer Dielectric) deposition or metallization. So these effects are observed as deposited Ni thickness differently on As doped SOI (Si film 30nm). Especially, the sheet resistance of Ni thickness deposited 20nm was lower than 30nm before the post silicidation annealing. But after the post silicidation annealing, the sheet resistance was changed. Therefore, in thin film SOI MOSFETs or Ni-FUSI technology that the Si film is less than 50nm, it is important to decide the thickness of deposited Ni in order to avoid forming high resistivity silicide.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2007년도 추계학술발표대회 및
• /
• pp.52.2-52.2
• /
• 2007

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.260-260
• /
• 2009

In high-efficiency crystalline silicon solar cell, If high-efficiency solar cells are to be commercialized, It is need to develop superior contact formation method and material that can be inexpensive and simple without degradation of the solar cells ability. For reason of plated metallic contact is not only high metallic purity but also inexpensive manufacture. It is available to apply mass production. Especially, Nickel, Copper are applied widely in various electronic manufactures as easily formation is available by plating. Ni is shown to be a suitable barrier to Cu diffusin as well as desirable contact metal to silicon. Nickel monosilicide has been suggested as a suitable silicide due to its lower resistivitym lower sintering temperature and lower layer stress than $TiSi_2$. In this paper, Nickel as a seed layer and diffusion barrier is plated by electroless plating to make nickel monosilicide.

• 한국재료학회지
• /
• 제18권1호
• /
• pp.5-11
• /
• 2008

Thermally evaporated 10 nm-Ni/1 nm-Au/(30 nm-poly)Si structures were fabricated in order to investigate the thermal stability of Au-inserted nickel silicide. The silicide samples underwent rapid thermal annealing at $300{\sim}1100^{\circ}C$ for 40 seconds. The sheet resistance was measured using a four-point probe. A scanning electron microscope and a transmission electron microscope were used to determine the cross-sectional structure and surface image. High-resolution X-ray diffraction and a scanning probe microscope were employed for the phase and surface roughness. According to sheet resistance and XRD analyses, nickel silicide with Au had no effect on widening the NiSi stabilization temperature region. Au-inserted nickel silicide on a single crystal silicon substrate showed nano-dots due to the preferred growth and a self-arranged agglomerate nano phase due to agglomeration. It was possible to tune the characteristic size of the agglomerate phase with silicidation temperatures. The nano-thick Au-insertion was shown to lead to self-arranged microstructures of nickel silicide.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.3-4
• /
• 2006

본 논문에서는 nano-scale CMOSFET을 위해 Boron Cluster ($B_{18}H_{22}$)가 이온주입된 SOI 와 Bulk 기판들 이용하였으며 실리사이드의 열 안정성 개선을 위해 Ni-V을 증착한 것과 순수 Ni을 증착한 것을 비교 분석 하였다. 결과 SOI위에 Ni-V을 증착한 것이 제일 낮은 면 저항을 보여주었고 반대로 Bulk위에는 제일 높은 면 저항을 보여 주었다. 단면을 측정한 결과 SOI 위에 Ni-V을 증착한 동일 조건의 Ni보다 Silicide의 두께가 두껍게 형성된 것을 확인하였다.