• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.15-20
• /
• 1995

We have prepared 20 kinds of Mn-Zn ferrites as content of CaO(0.1 mol%), NiO(0.0~0.60 mol%) and CoO(0.0~0.8 mol%) adding by the coprecipitation method and studied the magnetic properties as content of CaO, NiO and CoO adding. Initial permeability decrease as the content of NiO and CoO adding increases, while Curie tem~ perature increase as the content of NiO and CoO adding increases. $(H_{c})$, $(B_{s})$ and $(W_{h})$ increase as content of NiO adding increases.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.149-157
• /
• 2004

High temperature deformation behavior of activated sintered W powder compacts was investigated. The compression tests were carried out in the temperature range between 900 and 110$0^{\circ}C$ at the strain rate of $10^{-3}s^{-1}$. The sintered specimens of Ni-doped submicron W powder compacts showed decrease in W grain size with increasing the Ni content. As the result, the flow stress was significantly increased with increasing the Ni content. We obtained Ni-activated sintered W compacts with the relative density of 94 $\pm$ l％and the average grain size of less than 5${\mu}{\textrm}{m}$. A moderate true strain up to 0.60 was obtained without fracture even at 110$0^{\circ}C$ with the strain rate of $10^{-3}s^{-1}$ for the activated W compact despite adding the 1.0 wt％Ni to submicron W powder.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.168-170
• /
• 2001

The NiCr is an important material for present thin-film resistor application owing to its low TCR and thermal stability. In this work, the NiCr thin films were deposited on corning glass substrate by reactive magnetron sputtering and the annealing at temperatures range from 300 to $500^{\circ}C$ for 20 min in vacuum. X-ray, AFM, $R_s$(surface leakage current) have been used to study the structural and electrical properties of the NiCr thin films. The high precision NiCr thin films resistor with TCR(temperature coefficient of resistance) of less then 10 ppm/$^{\circ}C$ was obtained under in in-situ annealing at $300^{\circ}C$ on Cr buffer layer substrate. It is clear that the NiCr thin-films resistor electrical properties are low TCR related with it's annealing and buffer layer condition. NiCr thin film resistor having a good thermal stability and low TCR properties are expected for the application to the dielectric material of passive component.

• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.135-141
• /
• 2012

To improve the visible-light induced photocatalytic application performances of $TiO_2$, in this study, the $NiS_2$ modied $TiO_2$ composites were prepared by two methods: hydrothermal method and sol-gel method. The composites were denoted as hs-$NiS_2$/$TiO_2$, and sg-$NiS_2$/$TiO_2$ and characterized by XRD, UV-vis absorbance spectra, SEM, TEM, EDX, and BET analysis. The photocatalytic activities under visible light were investigated by the degradation of methyl orange (MO). The photodegradation rate of methyl orange under visible light with $NiS_2$/$TiO_2$ composites was markedly higher than that of pure $TiO_2$, and the effect of hs-$NiS_2$/$TiO_2$ composites was better than that of sg-$NiS_2$/$TiO_2$. The results indicate that the hydrothermal process could partly inhibit the agglomeration of $NiS_2$/$TiO_2$. Thus, the dispersion of nanoparticles was improved, and that the promoting effect of $NiS_2$ could extend the light absorption spectrum toward the visible region.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.156.1-156.1
• /
• 2016

Nickel sulfide (NiS) is one of the most promising candidates as an electrode material for supercapacitors due to its good capacitive properties, high electrical conductivity and low cost. In addition to the development of the new electrode materials, nanostructuring the electrode surface is one of the main issues in enhancing the capacitive performance of the supercapacitors because the increased surface area can improve the charge transfer and energy storage processes occurring at the electrode surface. However, most nanofabrication techniques require complicated and delicate nanoprocesses, and hence are not suitable for practical use. In this work, we developed a simple method to fabricate nanostructured NiS electrodes by depositing NiS onto $TiO_2$ nanoparticles. First, $TiO_2$ nanoparticles were spin-coated on a fluorine-doped tin oxide (FTO) substrate, and then NiS layers were deposited onto the $TiO_2$ nanoparticles by consecutive dip-coatings in the solutions containing nickel and sulfur precursors. This nanostructured NiS electrode showed significantly improved capacitive properties compared to the electrode of NiS films deposited without $TiO_2$ nanoparticles. The asymmetric full-cell supercapacitor with this nanostructured NiS electrode and activated carbon electrode was also fabricated and investigated.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.12a
• /
• pp.3-11
• /
• 2004

The power loss analysis was carried out for Ni-Cu-Zn ferrite samples with different content of NiO and ZnO. The power loss, Pcv decreases monotonically wi increasing temperature and attains to a certain value at around $100\~120$ degrees Celsius. The frequency dependence of Pcv can be explained by $Pcv\~f^n$', and n is independent of the frequency, f up to 1MHz. The Pcv decreases with an increase in ZnO/NiO. The Pcv was separated to hysteresis loss, Ph and residual loss, (Pcv-Ph). The temperature characteristics and compositional dependence of Pcv can be attributed to the Ph, while (Pcv-Ph) is not affected by both temperature and ZnO/NiO. By analyzing temperature and composition dependence of Ph and initial permeability, ${\mu}^i$ following equations could be formularized. $${\mu}_i{\mu}o=I_x\;^2/(K_1+bs_ol_s)\;\;\;\;(1)$$ $Wh=13.5(I_s\;^2/{\mu}_i{\mu}_o)\;\;\;\;(2)$$ Were ${\mu}_o$ is permeability of vacuum, $I_s$ saturation magnetization, $K_1$ anisotropy constant, $S_o$ internal heterogeneous stress, $I_s$, magnetostriction constant, b unknown constant. Wh hysteresis loss per one cycle of excitation (Ph: Wh*f). Steinmetz constant of Ni-Cu-Zn ferrites, $m=1.64\~2.2$ is smaller than the one of Mn-Zn ferrites, which suggests the difference of loss mechanism between these materials.

• Journal of Navigation and Port Research
• /
• v.37 no.6
• /
• pp.611-616
• /
• 2013

This paper studies relationship between typhoon and El Ni$\tilde{n}$o La Ni$\tilde{n}$a events by using 25 years meteorological data of KMA and JMA. The results are listed below. Annual mean number of typhoon's occurrence in El Ni$\tilde{n}$o event year is 23.9, and that in La Ni$\tilde{n}$a event year is 24.9. The number of typhoon's occurrence decreases in El Ni$\tilde{n}$o event year. Mean central minimum pressure and mean maximum wind speed in El Ni$\tilde{n}$o event year are 959.3hPa and 35.8m/s, and those in La Ni$\tilde{n}$a event year are 965.5hPa and 33.7m/s respectively. Intension of typhoon is stronger in El Ni$\tilde{n}$o event year than La Ni$\tilde{n}$a event year. To be more specific mean central minimum pressure is lower 6.2hPa and mean maximum wind speed is stronger 2.1m/s. This result is closely connected with sea area of typhoon's occurrence. Typhoons in El Ni$\tilde{n}$o event year are more likely to occur in east of 150E and south of 10N, but those in La Ni$\tilde{n}$a event year are more likely to occur in 120-150E and north of 20N. Typhoons which occur in east of 150E and south of 10N can be stronger because the typhoons move in broad sea area of high sea surface temperature in western North Pacific.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.4
• /
• pp.291-299
• /
• 2009

Ni-plated polytetrafluoroethylene(Ni-PTFE) particles($25{\mu}m$, $500{\mu}m$) were prepared by using nickel electroless plating. The Ni content in Ni-PTFE particles increased with increasing the amount of reduction agent. At about 53 wt% Ni content, $25{\mu}m$ Ni-PTFE particles showed conductivity of 320S/m. The Ni-PTFE particles were formed into the Ni-PTFE plate using heat treatment at $350^{\circ}C$ under $10{\sim}1000kg/cm^2$. The Ni-PTFE plate displayed the high conductivity of 5100S/m due to the formation of 3-dimentional Ni network. The plate was used as an electrode in an alkaline fuel cell(AFC). In terms of the current density, the Ni-PTFE electrode having higher Ni content(53 wt%) showed improved performance.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.1
• /
• pp.21-26
• /
• 2011

Ni-YSZ (Yttria Stabilized Zirconia) composite powders were fabricated by glycine nitrate process. The prepared powders were sintered at $1300{\sim}1400^{\circ}C$ for 4 h in air and reduced at $1000^{\circ}C$ for 2 h in a nitrogen and hydrogen atmosphere. The microstructure, electrical conductivity, thermal expansion and mechanical properties of the Ni-YSZ cermets have been investigated with respect to the volume contents of Ni. A porous microstructure consisting of homogeneously distributed Ni and YSZ phases together with well-connected grains was observed. It was found that the open porosity, electrical conductivity, thermal expansion and bending strength of the cermets are sensitive to the volume content of Ni. The Ni-YSZ cermet containing 40 vol% Ni was ascertained to be the optimum composition. This composition offers sufficient open porosity of more than 30 %, superior electrical conductivities of 917.4 S/cm at $1000^{\circ}C$ and a moderate average thermal expansion coefficient of $12.6{\times}10^{-6}^{\circ}C^{-1}$ between room temperature and $1000^{\circ}C$.

• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.311-321
• /
• 2007

We have researched the chemical defects of NiO ultrathin films grown on Ag(001) by x-ray photoelectron spectroscopy. In particular, O 1s and Ni 2p spectra were analyzed consistently with control film thickness, $O_2\;and\;H_2O$ partial pressure and substrate temperature. As a result, we could identify each chemical defect. In addition, we suggest the optimum growth condition to minimize the defect density.