• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.2
• /
• pp.108-121
• /
• 2009

The suspended particulate matters have been collected on membrane filters and glass fiber filters by an 8-stage cascade impactor for 2 years (Sep. 2005${\sim}$Sep. 2007) in Kyung Hee University-Global Campus located on the border of Yongin and Suwon. The 20 chemical species (Al, Mn, Si, Fe, Cu, Pb, Cr, Ni, V, Cd, Ba, $Na^+$, ${NH_4}^+$, $K^+$, $Mg^{2+}$, $Ca^{2+}$, $Cl^-$, ${NO_3}^-$, and ${SO_4}^{2-}$) were analyzed by an ICP-AES and an IC after performing proper pre-treatments of each sample filter. Based on these chemical information, the PMF receptor model was applied to identify the source of ambient size-by-size particulate matters. The receptor modeling is the one of the statistical methods to achieve resonable air pollution management strategies. A total of 10 sources was identified in 9 size-ranges such as long-range transport, secondary aerosol, $NH_{4}NO_{3}$ related source, coal combustion, sea-salt, soil, oil combustion, auto emission, incineration, and biomass burning. Especially, the secondary aerosol source assorted in fine and coarse modes was intensively studied.

• Journal of Environmental Science International
• /
• v.17 no.10
• /
• pp.1147-1154
• /
• 2008

Road runoff, one of non-point source pollutants, contains various heavy metals, most of which flow into discharge waters without being treated. The mechanism of removing the heavy metals in water is similar to that of removing micro-particles. Therefore, it is considered that it is possible to remove a lot of the heavy metals contained in the road runoff by filtering or absorbing them. In this paper, performed has been a basic study on the characteristics of UNFS (Up Flow Non-Point Source Filtering System) using carbide pellet and zeolite pellet as double-layer filtering mediums to treat the road runoff. The removal rate with filtering and absorption time has been shown as follows: 29.0% for Cr; 27.8% for Cd; 25.7% for Fe; 25.4% for Co; 21.2% for Pb; ]9.6% for Zn; 18.2% for Al; 17.0% for Mn; 11.3% for Ni; 7.5% for Cu. The overall removal rate according to influx change has been shown to be approximately 30%, and the load of heavy metals flowing out in initial precipitation could be reduced by using carbide as a recycling filtering medium. When the removal as coarse particles settle is added up, it is expected that UNFS will result in a higher removal rate.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.2
• /
• pp.140-149
• /
• 1998

The graphitization is affected by the addition of small amount of the elements, such as Si, Al, Ni, B, Cr and Mn etc. Boron is well known as the most effective element for the graphitization of cementite in high carbon steels. But a study on quantitative analysis of B effect on the graphitization is few reported. Therefore the effect of boron addition in Fe-0.65%C-1.0%Si-0.5%Mn steels on the graphitization is investigated quantitatively using hardness tester, optical microscope and scanning electron microscope, neutron induced microscopic radiography. The graphitization in high carbon steels is promoted with 0.003~0.005%B addition. But the graphitization in steels which has no boron takes long holding time at $680{\sim}720^{\circ}C$. The hardness of quenched steel containing 0.003%B is higher than that of 0.005%B added steel due to complete dissolution of fine graphites into the austenite. The 0.003%B added high carbon steel graphitized at $680^{\circ}C$ for 25hr is useful steel for the agricultural implements and automobile parts which needed a good formability and high hardness.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.245-245
• /
• 2015

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. 특히 CIGS 태양전지에서는 Na의 역할이 매우 중요한데 유연기판의 경우 이러한 Na이 없을 뿐만 아니라 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 또한 플라스틱기판의 경우 내열성이 낮아 저온에서 공정을 진행해야하는 단점이 있다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 유연기판으로 STS 430 stainless steel과 poly-imide를 이용하여 특성 개선을 진행하였다. 먼저 stainless steel과 Poly-imide, soda-lime glass, coning glass의 기판을 이용하여 기판에 따른 흡수층의 특성을 비교 분석하였으며 stainless steel 기판을 이용하여 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 이때 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.6%로 증가하였다. 또한 poly-imide 기판을 이용하여 $400^{\circ}C$이하에서 흡수층을 제조하여 특성평가를 진행하였으며 소자 제조 후 효율은 약 12.2%를 달성하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Economic and Environmental Geology
• /
• v.28 no.1
• /
• pp.53-67
• /
• 1995

Geochemical characteristics of iron-related Ulsan granite was studied in comparison with the Cretaceous granitoids from the metallogenic provinces of copper, lead-zinc and lead-zinc/molybdenum in the Gyeongsang Basin, and the variation of cheminal compositions at the Ulsan granite/serpentinite contact was investigated. Ulsan granite is plotted in the regions of granite and granodiorite of Streckeisen's diagram. It shows differentiation trend of calc-alkali magma, and the magmatic evolution from granodiorite to granite is consistant with the general crystallization path of the Cretaceous the granitoids in Gyeongsang Basin. Differentiation index(D.I.) of Ulsan granite is 86~95, which is higher than those of Jindong granites (D.I.=45~70) and Onjongri granites (D.I.=67~84), and there are differences in the content of some major and trace elements between Ulsan granite and other Cretaceous granitoids. At the Ulsan granite/serpentinite contact $SiO_2$, $K_2O$, $Na_2O$, $Al_2O_3$, Rb, Sr, Ba which are abundant in Ulsan granite decrease toward serpentinite, while T.Fe, MgO, Ni, Cr which are abundant in serpentinite decrease toward Ulsan granite. Therefore, the geochemical characteristics of Ulsan granite is applicable to distinguish iron province from different metallogenic provinces where other Cretaceous granitoids occur in the Gyeongsang Basin, and it is possible to find serpentinite which was intruded by granite on the basis of chemical variations.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.6
• /
• pp.701-717
• /
• 2003

The objective of this study was to extensively estimate the air quality trends of the study area by surveying con-centration trends in months or seasons, after analyzing the mass concentration of PM-10 samples and the inorganic lements, ion, and total carbon in PM-10. Also, the study introduced to apply the PMF (Positive Matrix Factoriza-tion) model that is useful when absence of the source profile. Thus the model was thought to be suitable in Korea that often has few information about pollution sources. After obtaining results from the PMF modeling, the existing sources at the study area were qualitatively identified The PM-10 particles collected on quartz fiber filters by a PM-10 high-vol air sampler for 3 years (Mar. 1999∼Dec.2001) in Kyung Hee University. The 25 chemical species (Al, Mn, Ti, V, Cr, Fe, Ni, Cu, Zn, As, Se, Cd, Ba, Ce, Pb, Si, N $a^{#}$, N $H_4$$^{+}$, $K^{+}$, $Mg^{2+}$, $Ca^{2+}$, C $l^{[-10]}$ , N $O_3$$^{[-10]}$ , S $O_4$$^{2-}$, TC) were analyzed by ICP-AES, IC, and EA after executing proper pre - treatments of each sample filter. The PMF model was intensively applied to estimate the quantitative contribution of air pollution sources based on the chemical information (128 samples and 25 chemical species). Through a case study of the PMF modeling for the PM-10 aerosols. the total of 11 factors were determined. The multiple linear regression analysis between the observed PM-10 mass concentration and the estimated G matrix had been performed following the FPEAK test. Finally the regression analysis provided source profiles (scaled F matrix). So, 11 sources were qualitatively identified, such as secondary aerosol related source, soil related source, waste incineration source, field burning source, fossil fuel combustion source, industry related source, motor vehicle source, oil/coal combustion source, non-ferrous metal source, and aged sea- salt source, respectively.ively.y.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.3
• /
• pp.406-417
• /
• 2018

In this study, $PM_{2.5}$ samples were collected during approximately 3 years in Chuncheon, a small residential and tourist city, in Korea. The average $PM_{2.5}$ concentration was $26.9{\mu}g/m^3$, exceeding the annual national air quality standard. $PM_{2.5}$ showed typical seasonal variation, having higher concentration in winter and lower concentration in summer. Sixteen metallic elements in $PM_{2.5}$ were also analyzed, and K was the highest contributor especially in late fall and winter. In addition, K considerably increased for the top 10% of $PM_{2.5}$ samples and showed the highest correlation coefficient with $PM_{2.5}$ among all other metallic elements. These results suggest that the combustion of agricultural residue and other biomass, the major source of K was likely to be important to high $PM_{2.5}$ concentration events in this city. Crustal elements including Al, Fe, Si, Ti, Mg showed high concentration in spring while Cr, Cu and Ni were relatively consistent throughout a year. Principal component analysis was used to trace the sources, and soil re-suspension, combustion of biomass and fossil fuels, and asphalt concrete production were identified as the main sources of $PM_{2.5}$.

• Journal of Powder Materials
• /
• v.22 no.3
• /
• pp.197-202
• /
• 2015

In this study, porous stainless steel (STS316L) sintered body was fabricated by powder metallurgy method and its properties such as porosity, compressive yield strength, hardness, and permeability were evaluated. 67.5Fe-17Cr- 13Ni-2.5Mo (wt%) powder was produced by a water atomization. The atomized powder was classified into size with under $45{\mu}m$ and over $180{\mu}m$, and then they were compacted with various pressures and sintered at $1210^{\circ}C$ for 1 h in a vacuum atmosphere. The porosities of sintered bodies could be obtained in range of 20~53% by controlling the compaction pressure. Compressive yield strength and hardness were achieved up to 268 MPa and 94 Shore D, respectively. Air permeability was obtained up to $79l/min{\cdot}cm^2$. As a result, mechanical properties and air permeability of the optimized porous body having a porosity of 25~40% were very superior to that of Al alloy.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.46 no.6
• /
• pp.930-940
• /
• 2013

We evaluated contamination with organic matter and trace metals by analyzing grain size, ignition loss (IL), chemical oxygen demand (COD), acid volatile sulfide (AVS), and trace metals (Al, Fe, Cu, Pb, Zn, Cd, Ni, Cr, Mn, Hg, and As) in surface sediments at 28 stations around the Geum River estuary in July 2008. The surface sediments in the estuary were mainly composed of coarse sediment (sand and muddy sand), with mean grain size (Mz) ranging between $2-4{\O}$. The high concentrations of IL, COD, and trace metals were mainly found at stations in front of the Gusan outer port and industrial complex, and near the Seocheon coast with relatively fine sediments. In addition, the concentrations of IL and all trace metals, except Pb and As, showed good positive correlations with Mz, indicating that the concentrations of organic matter and trace metals were mainly dependent on sediment grain size. The concentrations of COD, AVS, and trace metals in most sediments did not exceed the sediment quality guideline (SQGs). Although the sediments in the study region are not polluted with organic matter and trace metals, there are many point sources of pollutants, such as Gusan port and industrial complex, Janghang refinery, and a thermoelectric power plant around the Geum River estuary. Thus, the management of coastal environments through periodic monitoring of organic matter and trace metals is required in the future.

• Journal of environmental and Sanitary engineering
• /
• v.19 no.1
• /
• pp.8-16
• /
• 2004

Ground water samples were collected from residential, green" industrial, landfill and mining area and analyzed for 23 inorganics from March to October in 2002. The results are as follows; 1. The detection frequencies of inorganic materials such as As, Ba, B, Mo, Ca, Mg, Al, Cu, Fe, Mn, Zn, Na, K were 7.2∼77.1% which showed that these inorganics were detected in many ground waters. 2. The detection frequencies of 7 inorganics(Cd, Cr, Ph, Se, Sb, Be, Tl) were commonly low at ranging from 0.42 to 2.5%. These inorganics were contained in ground water partially. 3. Three inorganics such as Hg, Ni, Ag were not detected in any ground-water samples. 4. Compared to the other areas, ground water samples from landfill area contained greater concentration in many inorgainics and then showed higher levels in industral, residential, mining and green area in order. 5. Compared to noted concentrations of bottled water, inorganic minerals including Ca, Mg, Na, K related to taste were fluent in target samples. The results showed that the average concentrations of Mg, Na, K were 4.0 mg/l, 14.7 mg/l, 1.5 mg/l respectively. 6. The concentrations of inorganics such as Sb, Ba, Mo, Be, Tl, K in some ground water samples exceeded the water quality standards of WHO, the US and UK. Especially, Ba, Mo, K also showed relatively high detection frequencies so these inorganics need to be considered as analytes in Korea Drinking Water Regulation in further study.