• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.71-71
• /
• 2009

This paper describes a simple, on-chip CMOS compatible the thin-film inductor applied for the dc-dc converters. A fully CMOS-compatible thin-film inductor with a bottom NiFe core is integrated with the DC-DC converter circuit on the same chip. By eliminating ineffective top magnetic layer, very simple process integration was achieved. Fabricated monolithic thin film inductor showed fairly high inductance of 2.2 ${\mu}H$ and Q factor of 11.2 at 5MHz. When the DC-DC converter operated at $V_{in}=3.3V$ and 5MHz frequency, it showed output voltage $V_{out}=8.0V$, and corresponding power efficiency was 85%.

• 전자공학회논문지D
• /
• 제34D권5호
• /
• pp.45-51
• /
• 1997

Low temperature activation of dopants which were doped using ion mass doping system in amorphous silicon(a-Si) thin films was investigated. With a 20.angs.-thick Ni film on top of the a-Si thin film, the activation temperature of dopants lowered to 500.deg. C. When the doping was performaed after the deposition of Ni thin film on the a-Si thin films (post-doping), the activation time was shorter than that of dopants mass, the activation time of the dopants doped by pre-doping method increased. It turned NiSi2 formation, while the decrease of activation time was mainly due to the enhancement of the NiSi2 formation by mixing of Ni and a-Si at the interface of Ni and a -Si thin during the ion doping process.

• 한국재료학회지
• /
• 제28권10호
• /
• pp.595-600
• /
• 2018

This study investigates the microstructural properties of CoCrFeMnNi high entropy alloy (HEA) oxynitride thin film. The HEA oxynitride thin film is grown by the magnetron sputtering method using nitrogen and oxygen gases. The grown CoCrFeMnNi HEA film shows a microstructure with nanocrystalline regions of 5~20 nm in the amorphous region, which is confirmed by high-resolution transmission electron microscopy (HR-TEM). From the TEM electron diffraction pattern analysis crystal structure is determined to be a face centered cubic (FCC) structure with a lattice constant of 0.491 nm, which is larger than that of CoCrFeMnNi HEA. The HEA oxynitride film shows a single phase in which constituting elements are distributed homogeneously as confirmed by element mapping using a Cs-corrected scanning TEM (STEM). Mechanical properties of the CoCrFeMnNi HEA oxynitride thin film are addressed by a nano indentation method, and a hardness of 8.13 GPa and a Young's modulus of 157.3 GPa are obtained. The observed high hardness value is thought to be the result of hardening due to the nanocrystalline microstructure.

• 한국표면공학회지
• /
• 제44권2호
• /
• pp.68-73
• /
• 2011

A Ni-W thin-film was synthesized by electrodeposition, and its corrosion resistance and electrical surface conductivity were investigated. Amount of tungsten in the Ni-W thin-film increased linearly with current density during the electrodeposition, and crack-free and low-crystalline Ni-21 at.%W coating layer was obtained. Corrosion resistances of the Ni-W thin-films were examined with an anodic polarization method and a storage test in a strong sulfuric acid solution. As a result, the Ni-21 at.%W thin-film exhibited the greatest corrosion resistance, and maintained the electrical surface conductivity even after the severe corrosion test, which could be applicable as a surface treatment for advanced metallic bipolar plates in fuel cell or redox flow battery systems.

• 한국전기전자재료학회논문지
• /
• 제20권6호
• /
• pp.520-526
• /
• 2007

In order to acquire fundamental informations to fabricate high precision thin film resistors, NiCr/NiCrSi alloy films were prepared using Ni and Cr targets. Effect of composition on the electrical properties of the NiCr/NiCrSi alloy film were then investigated. Considering the effect of Si doping on the electrical and material characteristics, the lower TCR (temperature coefficient of resistance) values could be achieved for samples with Ni/Cr ratio of $0.8{\sim}1.5$ (in a range of relative higher specific resistivity and Cr composition of $40\;wt%{\sim}55\;wt%$) and with Si doping. Consequently, the sample prepared using a DC power showed a good TCR of $-25\;ppm/^{\circ}C$, which implies that increase of specific resistivity and decrease of TCR would be achieved more efficiently not for Ni-Cr binary material but for Si doped Ni-Cr ternary material, and not using RF power but using DC power in the sputtering process.

• 한국전기전자재료학회논문지
• /
• 제14권1호
• /
• pp.74-83
• /
• 2001

In this study, the optimum structure of a magnetic thin film inductor was designed for application of DC-DC converters. The Ni$\sub$81/Fe$\sub$19/ (at%) alloy was selected as a high-frequency($\geq$MHz) magnetic thin film magnetron sputtering system. As-deposited NiFe thin films show similar magnetic properties compared to bulk NiFe alloys, indicating that they have a good film quality. The optimum design of dolenoid-type magnetic thin film inductors was performed utilizing a Maxwell computer simulator (Ansoftt HFSS V7.0 for PC) and parameters obtained from the magnetic properties of magnetic core materials selected. The high-frequency characteristics of the inductance(L) and quality factor(Q) obtained for the designed inductors through simulation agreed well with those obtained by theoretical calculations, confirming that the simulated result is realistic. The optimum structure of high-performance (Q$\geq$60, L = 1${\mu}$H, efficiency $\geq$90%), high-frequency ($\geq$5MHz), and solenoid-type magnetic thin film inductors was designed successfully.

• 한국표면공학회지
• /
• 제43권5호
• /
• pp.243-247
• /
• 2010

The micro Vickers hardness and internal stress of Ni-Fe metal thin film synthesized by electrodeposition method at $25^{\circ}C$ were studied as a function of bath composition, and surface microstructure and atomic compositions of thin films were investigated by SEM and EDS. And the shape change of $200\;{\AA}$ Ni-Fe nanowires made using anodic aluminum oxide(AAO) templates by electrodeposition method were observed by SEM as a function of ultrasonic treatment time and bath composition. The Fe deposition contents on the substrate non-linearly increased with Fe ion concentration over total metal ion concentration. In case of low Fe contents film, the grain size is smaller and denser than high Fe contents deposited films, and the micro Vickers hardness increased with Fe contents of electrodeposited films. These results affected the shape change of nanowire after ultrasonic treatments.

• 한국전기전자재료학회논문지
• /
• 제14권4호
• /
• pp.328-335
• /
• 2001

In this work, we made the precision thin film resistors of NiCr alloy (74wt%Ni-f18wt%Cr-4wt%Al-4wt%Cu) using DC/RF magnetron sputtering method and studied the sheet resistance and TCR(Temperature Coefficient of Resistance) etc... of the Ni-Cr-Al-Cu alloy thin film according to the change by annealing treatment to 400$\^{C}$ in air and nitrogen atmosphere and the change(power, pressure, substrate temperature) of sputtering process.

• ETRI Journal
• /
• 제25권4호
• /
• pp.270-273
• /
• 2003

This paper presents a simple process to integrate thin-film inductors with a bottom NiFe magnetic core. NiFe thin films with a thickness of 2 to 3${\mu}m$ were deposited by sputtering. A polyimide buffer layer and shadow mask were used to relax the stress of the NiFe films. The fabricated double spiral thin-film inductor showed an inductance of 0.49${\mu}H$ and a Q factor of 4.8 at 8 MHz. The DC-DC converter with the monolithically integrated thin-film inductor showed comparable performances to those with sandwiched magnetic layers. We simplified the integration process by eliminating the planarization process for the top magnetic core. The efficiency of the DC-DC converter with the monolithic thin-film inductor was 72% when the input voltage and output voltage were 3.5 V and 6 V, respectively, at an operating frequency of 8 MHz.

• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.37-42
• /
• 2004

최근에 3 ㎓이상의 고주파용 전자부품과 소자의 제조에 낮은 저항온도계수(TCR)값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_Al_3Mn_4Si$(wt%)이 첨가된 우수한 저항특성을 갖는 S-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C$, 300$300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$로 변화시키면서 고주파 박막 저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.