• Journal of Soil and Groundwater Environment
• /
• v.21 no.1
• /
• pp.28-39
• /
• 2016

Struvite (MgNH₄PO₄ ⋅ 6H₂O) and hydroxyapatite (HAP, Ca₁₀(PO₄)₆(OH)₂) precipitation in urine-separating toilets (NoMix toilets) causes severe maintenance problems and also reduce the phosphate and calcium content. Application of urine separating technique and extraction of by-products from human urine is a cost effective technique in waste water treatment. In this study, we extract urine calcite from human urine by batch scale method, using urease producing microbes to trigger the precipitation and calcite formation process. Extracted urine calcite (calcining at 800℃) is a potential adsorbent for removal of heavy metal(loid)s like (Cd²⁺, Cu²⁺, Ni²⁺, Pb²⁺, Zn²⁺ and As³⁺) along with additional leaching analysis of total nitrogen (T-N), phosphate (T-P) and chemical oxygen demand (COD). The transformations of calcite during synthesis were confirm by characterization using XRD, SEM-EDAX and FT-IR techniques. In additional, the phosphate leaching potential and adsorbate (nitrate) efficiency in aqueous solution was investigated using the calcinedurine calcite. The results indicate that the calcite was effectively remove heavy metal(loid)s lead up to 96.8%. In addition, the adsorption capacity (q_e) of calcite was calculated and it was found to be 203.64 Pb, 110.96 Cd, 96.02 Zn, 104.2 As, 149.54 Cu and 162.68 Ni mg/g, respectively. Hence, we suggest that the calcite obtain from the human urine will be a suitable absorbent for heavy metal(loid)s removal from aqueous solution.

• Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.212-219
• /
• 2009

Emission characteristics of air pollutants from three commercially operating cement kilns co-burning waste were investigated. The major heavy metals emitted were mercury (Hg), zinc (Zn), nickel (Ni), chromium (Cr), lead (Pb), cadmium (Cd), and arsenic (As) Removal efficiency of the bag filter was above 98.5% for heavy metals (except Hg), and above 60% for Hg. Higher fractions of heavy metals entering the bag filter were speciated to cement kiln dust. On average, 3.3% of the -heavy metals of medium and low toxicity (Pb, Ni, and Cr) entering the bag filter were released into the atmosphere. Among highly toxic heavy metals, 0.14% of Cd, 0.01% of As, and 40% of Hg entering the bag filter were released into the atmosphere. In passing through the bag filter, the proportion of oxidized Hg in all cases increased. Emission variations of hazardous air pollutants in cement kilns tested were related to raw materials, fuel, waste feed and operating conditions. Volatile organic compounds detected in gas emissions were toluene, acrylonitrile benzene, styrene, 1,3-butadiene, and methylene chloride. Although hazardous air pollutants in emissions from cement kilns co-burning waste were within the existing emission limit, efforts are required to minimize their levels.

• Environmental Engineering Research
• /
• v.19 no.1
• /
• pp.15-22
• /
• 2014

In this study, the performances of various adsorbents-red mud, zeolite, limestone, and oyster shell-were investigated for the adsorption of multi-metal ions ($Cr^{3+}$, $Ni^{2+}$, $Cu^{2+}$, $Zn^{2+}$, $As^{3+}$, $Cd^{2+}$, and $Pb^{2+}$) from aqueous solutions. The result of scanning electron microscopy analyses indicated that the some metal ions were adsorbed onto the surface of the media. Moreover, Fourier transform infrared spectroscopy analysis showed that the Si(Al)-O bond (red mud and zeolite) and C-O bond (limestone and oyster shell) might be involved in heavy metal adsorption. The changes in the pH of the aqueous solutions upon applying adsorbents were investigated and the adsorption kinetics of the metal ions on different adsorbents were simulated by pseudo-first-order and pseudo-second-order models. The sorption process was relatively fast and equilibrium was reached after about 60 min of contact (except for $As^{3+}$). From the maximum capacity of the adsorption kinetic model, the removal of $Pb^{2+}$ and $Cu^{2+}$ were higher than for the other metal ions. Meanwhile, the reaction rate constants ($k_{1,2}$) indicated the slowest sorption in $As^{3+}$. The adsorption mechanisms of heavy metal ions were not only surface adsorption and ion exchange, but also surface precipitation. Based on the metal ions' adsorption efficiencies, red mud was found to be the most efficient of all the tested adsorbents. In addition, impurities in seawater did not lead to a significant decrease in the adsorption performance. It is concluded that red mud is a more economic high-performance alternative than the other tested adsorption materials for applying a removal of multi-metal in seawater.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.6
• /
• pp.19-28
• /
• 2009

The acid mine drainage (AMD) and landfill leachates released into the subsurface environment can result in serious environmental problems like soil and groundwater contamination. The AMD and the leachates of landfill were known to contain many heavy metals. In this study, the author assessed the reactivity and ability of the FeS coated-ALC for the removal of contaminants (As, Cd, Cu, Pb, Ni, Zn, Al) in AMD and leachates in landfill. The synthetic nano-FeS and Autoclaved Lightweight Concrete (ALC) were used as reactive materials in the permeable reactive barriers(PRBs). The result of batch test indicated that synthetic nano-FeS can remove 99% of heavy metals for the 1hr of reaction time except for As and Ni(about 90%). However, the 80% of As and Ni was removed in column 1(FeS coated-ALC). The column 2(Ore FeS) removed more than 99% of heavy metals. The pH of the column 1 was increased from 3.51 to 6.39~6.50, and the pH with column 2 was increased from 3.51 to 9.20. As the result of this study, the author can surmise that the synthetic nano-FeS coated ALC will use as a very good reactive material of the PRBs to treat the contaminated groundwater with AMD and leachate of landfill.

• Korean Journal of Environmental Agriculture
• /
• v.32 no.2
• /
• pp.108-116
• /
• 2013

BACKGROUND: Certain crop-based waste materials have been recognized as cost-effective and highly efficient adsorbents for removal and recovery of different kind of heavy metals from aqueous solutions. The ability is strongly attributed to the carboxyl functional group of some pectin substances such as galacturonic acid often found in fruit peels. The present manuscript was aimed at assessing the potential applicability of banana peel for metal removal from contaminated waters. METHODS AND RESULTS: As revealed by laboratory investigations, banana peel contains pectin (10-21%), lignin (6-12%), cellulose (7.6-9.6%), and hemicelluloses (6.4-9.4%). The pectin extraction is reported to have glucose, galactose, arabinose, rhamnose, xylose, and galactouroninc acid. Several studies conducted under different conditions proved that banana peel is capable of adsorbing 5.71, 2.55, 28.00, 6.88, 7.97, and 5.80 mg/g of $Cd^{2+}$, $Co^{2+}$, $Cu^{2+}$, $Ni^{2+}$, $Pb^{2+}$, and $Zn^{2+}$, respectively, from aqueous solutions. Adsorption capacity is, however, dependent upon several factors including solution pH, dose of adsorbent and metal concentration, contact time and shaking speed. CONCLUSION(S): Since the annual world production of banana exceeds 100 million tons, about 40 million tons of banana peel (40% of total weight of the fresh fruit) remains vastly unused. Exploring a sound technology with banana peel would therefore, not only address the much needed sustainable tool for cleaning contaminated waters, but of course bring an additional value to the banana industry worldwide.

• Journal of Environmental Science International
• /
• v.17 no.10
• /
• pp.1147-1154
• /
• 2008

Road runoff, one of non-point source pollutants, contains various heavy metals, most of which flow into discharge waters without being treated. The mechanism of removing the heavy metals in water is similar to that of removing micro-particles. Therefore, it is considered that it is possible to remove a lot of the heavy metals contained in the road runoff by filtering or absorbing them. In this paper, performed has been a basic study on the characteristics of UNFS (Up Flow Non-Point Source Filtering System) using carbide pellet and zeolite pellet as double-layer filtering mediums to treat the road runoff. The removal rate with filtering and absorption time has been shown as follows: 29.0% for Cr; 27.8% for Cd; 25.7% for Fe; 25.4% for Co; 21.2% for Pb; ]9.6% for Zn; 18.2% for Al; 17.0% for Mn; 11.3% for Ni; 7.5% for Cu. The overall removal rate according to influx change has been shown to be approximately 30%, and the load of heavy metals flowing out in initial precipitation could be reduced by using carbide as a recycling filtering medium. When the removal as coarse particles settle is added up, it is expected that UNFS will result in a higher removal rate.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.5
• /
• pp.26-34
• /
• 2014

A $1.5m(L){\times}1.0m(W){\times}1.1m(H)$ polypropylene (PP) field scale electroniketic system coupled with stainless steel electrodes was designed to examined metal removal performance applied 0.2-0.35 V/cm potential gradient and 0.05-0.5M lactic acid for 20 day. Electroosmosis permeabilities of $2.2{\times}10^{-5}cm^2/V-s$ to $4.8{\times}10^{-5}cm^2/V-s$ were observed and it increased with the potential gradient increased. The reservoir pH controlled at $7.0{\pm}1.0$ has been effectively diminished the clogging of most metal oxides. The best removal efficiency of Zn, Pb, and Ni was 78.4%, 84.3%, and 40.1%, respectively, in the field scale EK system applied 0.35 V/cm and 0.05M lactic acid for 20 days. Increasing potential gradient would more effectively enhance metal removal than increasing concentration of processing fluid. The reservoir and soil temperatures were majorly related to potential gradient and power consumptio. A $4-16^{\circ}C$ above room temperature was observed in the investigated system. It was found that the temperature increase in soil transported the pore water and metals from bottom to the topsoil. This vertical transport phenomenon is critical for the electrokinetic process to remediate in-situ deep pollution.

• Korean Journal of Environmental Agriculture
• /
• v.23 no.4
• /
• pp.240-244
• /
• 2004

The objective of this research was to develop the adsorbent far heavy metals by activating the bark sample. Barks from pine tree with diameters of $2{\sim}4\;mm$ were activated in the muffle furnace under a high relative humidity condition at temperatures of $600{\sim}900^{\circ}C$. The removal efficiency of the activated bark (ACTBARK) for Cu and Cd was temperature dependent showing the order of $900^{\circ}C$ > $800^{\circ}C$ > $700^{\circ}C$ > $600^{\circ}C$. The critical temperature was considered to be $900^{\circ}C$ to become an efficient adsorbent for Cu and Cd. The bark samples activated at temperatures lower than $700^{\circ}C$ showed a less removal efficiency than the crude bark. The ACTBARK activated at $900^{\circ}C$ removed more Cu and Cd from solution than the commercial activated carbon and charcoal. The ACTBARK (activated at $900^{\circ}C$) adsorbed all of the Cu and Cd in solution with concentrations less than 150 mg/L. The selectivity of the ACTBARK was in the order of Cu > Zn > Ni > Pb > Fe > Cd > Mn.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.6
• /
• pp.75-80
• /
• 2005

Several metalliferous including Guedo mine, Manjung mine and Joil mine located at the upper watershed of Namhan river, were abandoned or closed since 1988 due to the mining industry promotion policy and thus disposed an enormous amount of mining wastes without a proper treatment facilities, resulting in soil pollution. In this research, total and fractional concentrations of heavy metals in mining wastes were analyzed and accordingly the degree of soil pollutions in the abandoned mine area were quantitatively assessed employing the several pollution indices. The mining waste samples from Guedo mine, Manjung mine and Joil mine recently abandoned were collected for the evaluation of the potential of water pollution by mining activities. Index of geoaccumulation fractional composition and removal efficiency of some heavy metals by different concentration of HCl treatment were analyzed. Index of geoaccumulation of Cd, Pb, Zn, Cu, Ni and Cr are 6, $4\~6,\;0\~6,\;4\~5$, 2 and 0 respectively. The index of geoaccumulation of Cd, Pb, Zn and Cu reveals the mining wastes has high pollution potential in the area. According to sequential extraction of metals in the mine wastes organic fraction of Cu, reducible fraction of Pb, residual fraction of Ni and Zn were the most abundant fraction of heavy metals in mining wastes.

• Nuclear Engineering and Technology
• /
• v.55 no.3
• /
• pp.1061-1070
• /
• 2023

Over the last few years, lead-free inorganic metal perovskites have gained impressive ground in empowering satellites in space exploration owing to their material stability and performance evolution under extreme space environments. The present work has examined the versatility of eight such perovskites as space radiation shielding materials by computing their photon, charged particles and neutron interaction parameters. Photon interaction parameters were calculated for a wide energy range using PAGEX software. The ranges of heavy charged particles (H, He, C, N, O, Ne, Mg, Si and Fe ions) in these perovskites were estimated using SRIM software in the energy range 1 keV-10 GeV, and that of electrons was computed using ESTAR NIST software in the energy range 0.01 MeV-1 GeV. Further, the macroscopic fast neutron removal cross-sections were also calculated to estimate the neutron shielding efficiencies. The examined shielding parameters of the perovskites varied depending on the radiation type and energy. Among the selected perovskites, Cs₂TiI₆ and Ba₂AgIO₆ displayed superior photon attenuation properties. A 3.5 cm thick Ba₂AgIO₆-based shield could reduce the incident radiation intensity to half its initial value, a thickness even lesser than that of Pb-glass. Besides, CsSnBr₃ and La_0.8Ca_0.2Ni_0.5Ti_0.5O₃ displayed the highest and lowest range values, respectively, for all heavy charged particles. Ba₂AgIO₆ showed electron stopping power (on par with Kovar) better than that of other examined materials. Interestingly, La_0.8Ca_0.2Ni_0.5Ti_0.5O₃ demonstrated neutron removal cross-section values greater than that of standard neutron shielding materials - aluminium and polyethylene. On the whole, the present study not only demonstrates the employment prospects of eco-friendly perovskites for shielding space radiations but also suggests future prospects for research in this direction.