• Journal of Information Processing Systems
• /
• 제14권3호
• /
• pp.771-789
• /
• 2018

In heterogeneous wireless networks supporting multi-access services, selecting the best network from among the possible heterogeneous connections and providing seamless service during handover for a higher Quality of Services (QoSs) is a big challenge. Thus, we need an intelligent vertical handover (VHO) decision using suitable network parameters. In the conventional VHOs, various network parameters (i.e., signal strength, bandwidth, dropping probability, monetary cost of service, and power consumption) have been used to measure network status and select the preferred network. Because of various parameter features defined in each wireless/mobile network, the parameter conversion between different networks is required for a handover decision. Therefore, the handover process is highly complex and the selection of parameters is always an issue. In this paper, we present how to maximize network utilization as more than one target network exists during VHO. Also, we show how network parameters can be imbedded into IEEE 802.21-based signaling procedures to provide seamless connectivity during a handover. The network simulation showed that QoS-effective target network selection could be achieved by choosing the suitable parameters from Layers 1 and 2 in each candidate network.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.44-51
• /
• 1998

Two-step neural network is designed for determining electrical discharge machining parameters in low erosion. The first neural network, which is used as a classification network, checks whether the current conditions are appropriate to electrical discharge machining in low tool erosion. If the conditions are appropriate to EDM in low erosion, suitable EDM parameters are generated by the second neural network. Theoretically known EDM conditions are produced and also utilized for training the second neural network. The trained neural network is tested how well suitable EDM machining conditions are generated under unknown machining situations Experimental result shows that the proposed two-step neural network approach could be effectively used for determining EDM parameters in low tool erosion. The results also have a practical contribution to EDM area in that it could be applied for maintaining low tool wear as well as obtaining maximum machining rates simultaneously.

• 한국전자파학회논문지
• /
• 제26권2호
• /
• pp.119-126
• /
• 2015

잡음 파라미터에 대한 정보는 저잡음 증폭기 설계에 있어 필수 불가결한 요소이다. 과거 잡음 파라미터는 임피던스 튜너와 잡음지수 측정기(Noise Figure Analyzer: NFA)를 사용 측정되어 왔다. 최근 저자들은 잡음 파라미터는 기계적으로 구동되는 임피던스 튜너 없이 8-포트 회로망 방법을 이용하여 측정될 수 있음을 보였다. 그러나 8-포트 회로망을 이용한 측정방법은 여전히 잡음원(noise source)을 이용하고, 측정의 복잡도를 증가시키는 면이 있다. 본 논문에서는 잡음원을 이용하지 않고, 잡음 파라미터를 측정할 수 있는 새로운 6-포트 회로망 방법을 제안한다. 6-포트 회로망 방법에 의해 이론적으로 알려진 잡음 파라미터를 갖고 있는 10-dB 감쇠기에 대해 측정하였으며, 측정된 잡음 파라미터 결과는 기존 8-포트 회로망 방법과 비교하였으며, 비교결과 8-포트 회로망 방법과 유사한 정확도를 갖는 것을 보였다.

• 대한교통학회지
• /
• 제14권3호
• /
• pp.127-141
• /
• 1996

This paper presents a unique approach to urban traffic network signal control. This paper begins with an introduction to traffic control in general, and then goes on to describe the approach of fuzzy control, where the signal timing parameters at a given intersection are adjusted as functions of the local traffic network condition and adjacent intersection. The signal timing parameters evolve dynamically using only local information to improve traffic signal flow. The signal timing at an intersection is defined by three parameters : cycle time, phase split, off set. Fuzzy decision rules are used to adjust three parameters based only on local information. The amount of change in the timing parameters during each cycle is limited to a small fraction of the current parameters to ensure smooth transition. In this paper the effectiveness of this method is showed through simulation of the traffic signal flow in a network of controlled intersection.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2016년도 추계학술발표대회
• /
• pp.114-116
• /
• 2016

Recently, SDN and NFV technology have been developed actively and provide enormous flexibility of network provisioning. The future network services would generally involve many different types of services such as hologram games, social network live streaming videos and cloud-computing services, which have dynamic service requirements. To provision networks for future services dynamically and efficiently, SDN/NFV orchestrators must clearly understand the service requirements. Currently, network provisioning relies heavily on QoS parameters such as bandwidth, delay, jitter and throughput, and those parameters are necessary to describe the network requirements of a service. However it is often difficult for users to understand and use them proficiently. Therefore, in order to maintain interoperability and homogeneity, it is required to have a service abstraction layer between users and orchestrators. The service abstraction layer analyzes ambiguous user's requirements for the desired services, and this layer generates corresponding refined services requirements. In this paper, we present our initial effort to design a Smart Service Abstraction Layer (SmSAL) for future network architecture, which takes advantage of machine learning method to analyze ambiguous and abstracted user-friendly input parameters and generate corresponding network parameters of the desired service for better network provisioning. As an initial proof-of-concept implementation for providing viability of the proposed idea, we implemented SmSAL with a decision tree model created by learning process with previous service requests in order to generate network parameters related to various audio and video services, and showed that the parameters are generated successfully.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.74-80
• /
• 1998

The morphologies of the wear particles are directly indicative of wear process occuring in the machine. The analysis of wear particle morphology can therefore provide very early detection of a fault and can also ofen facilitate a dignosis. For this work, the neural network was applied to identify friction coefficient through four shape parameters (50% volumetric diameter, aspect, roundness and reflectivity) of wear debris generated from the machine. The averages of these parameters were used as inputs to the network. It is shown that collect identification of friction coefficient depends on the ranges of these shape parameters learned. The various kinds of the wear debris had a different pattern characteristics and recognized relation between the friction condition and materials very well by neural network. We discuss how the network determines difference in wear debris feature, and this approach can be applied for machine condition monitoring and fault diagnosis.

• Journal of Welding and Joining
• /
• 제11권4호
• /
• pp.44-56
• /
• 1993

The arc welding processes are substantially nonlinear, in addition to being highly coupled multivariable systems, Frequently, not all the variables affecting the welding quality are known, nor may they be easily quantified. From this point of view, decoupling between the welding parameters from the welding quality is very difficult, which makes it also difficult to control the welding parameters for obtaining the desired welding quality. In this study, a neural network based on the backpropagation algorithm was implemented and adopted for the selection of gas metal arc welding parameters of the fillet joint, that is, welding current, arc voltage and welding speed. The performance of the neural network for modeling the relationship between the welding quality and welding parameters was presented and evaluated by using the actual welding data. To obtain the optimal neural network structure, various types of the neural network structures were tested with the experimental data. It was revealed that the neural network can be effectively adopted to select the appropriate gas metal arc welding parameter of fillet joints for a given weld quality.

• International Journal of Computer Science & Network Security
• /
• 제23권10호
• /
• pp.169-178
• /
• 2023

Wireless sensor network is wieldy use for IoT application. The sensor node consider as physical device in IoT architecture. This all sensor node are operated with battery so the power consumption is very high during the data communication and low during the sensing the environment. Without proper planning of data communication the network might be dead very early so primary objective of the cluster based routing protocol is to enhance the battery life and run the application for longer time. In this paper we have comprehensive of twenty research paper related with clustering based routing protocol. We have taken basic information, network simulation parameters and performance parameters for the comparison. In particular, we have taken clustering manner, node deployment, scalability, data aggregation, power consumption and implementation cost many more points for the comparison of all 20 protocol. Along with basic information we also consider the network simulation parameters like number of nodes, simulation time, simulator name, initial energy and communication range as well energy consumption, throughput, network lifetime, packet delivery ration, jitter and fault tolerance parameters about the performance parameters. Finally we have summarize the technical aspect and few common parameter must be fulfill or consider for the design energy efficient cluster based routing protocol.

• Nuclear Engineering and Technology
• /
• 제32권5호
• /
• pp.485-494
• /
• 2000

In this work, a fuzzy neural network is used to estimate the relevant sensor signal using other sensor signals. Noise components in input signals into the fuzzy neural network are removed through the wavelet denoising technique . Principal component analysis (PCA) is used to reduce the dimension of an input space without losing a significant amount of information. A lower dimensional input space will also usually reduce the time necessary to train a fuzzy-neural network. Also, the principal component analysis makes easy the selection of the input signals into the fuzzy neural network. The fuzzy neural network parameters are optimized by two learning methods. A genetic algorithm is used to optimize the antecedent parameters of the fuzzy neural network and a least-squares algorithm is used to solve the consequent parameters. The proposed algorithm was verified through the application to the pressurizer water level and the hot-leg flowrate measurements in pressurized water reactors.

• 방사성폐기물학회지
• /
• 제20권3호
• /
• pp.269-278
• /
• 2022

The buffer is a critical barrier component in an engineered barrier system, and its purpose is to prevent potential radionuclides from leaking out from a damaged canister by filling the void in the repository. No experimental parameters exist that can describe the buffer expansion phenomenon when Kyeongju bentonite, which is a buffer candidate material available in Korea, is exposed to groundwater. As conventional experiments to determine these parameters are time consuming and complicated, simple swelling pressure tests, numerical modeling, and machine learning are used in this study to obtain the parameters required to establish a numerical model that can simulate swelling. Swelling tests conducted using Kyeongju bentonite are emulated using the COMSOL Multiphysics numerical analysis tool. Relationships between the swelling phenomenon and mechanical parameters are determined via an artificial neural network. Subsequently, by inputting the swelling tests results into the network, the values for the mechanical parameters of Kyeongju bentonite are obtained. Sensitivity analysis is performed to identify the influential parameters. Results of the numerical analysis based on the identified mechanical parameters are consistent with the experimental values.