• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.913-920
• /
• 2005

Compared to previous in-vitro test, FE model showed reliable motion patterns. A finite element model of a 50th percentile male neck was developed to study the mechanics of whiplash injury while the rear impacts. The model was consisted of the whole cervical vertebrae including part of occipital, intervertebral discs. which were modeled using linear viscoelastic materials and posterior elements. The sliding interfaces were defined to simulate contact phenomena in facet joints and in odontoid process. All ligaments and atlanto-occipital membrane were modeled as nonlinear bar elements. Only muscle elements were not considered. Motion of each cervical vertebra was obtained from the dynamic simulation with a MADYMO model for 15 km/h $40\%$ rear end offset impacts. Soft tissue neck injury(STNI) was investigated with a developed FE model. In FE model analysis, the high stress was appeared at C3/C4 disc in offset impact. Further research is still needed in order to improve the developed neck FE model for many different crash patterns.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.135-142
• /
• 2007

MADYMO human model with the detail neck was used to investigate the reaction force of neck and neck injury from rear impact directions. In the validation simulation, head acceleration, thorax acceleration and the global kinematics of the head and neck were correlated well with experimental data. Acceleration data from three 15 km/h low speed car rear impact pendulum tests(rear-end, offset, oblique) were used to simulate the model. In the simulation results, the reaction force on the facet joint and discs in the oblique rear impact were higher than rear-end, offset rear impacts. Further research is still needed in order to neck injury analysis about different crash parameters.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.17 no.4
• /
• pp.283-305
• /
• 2001

The purpose of this study was to analyze the stress distribution of condylar regions and edentulous mandible with implant-supported cantilever prostheses on the certain conditions, such as amount of load, location of load, direction of load, fixation or non-fixation on the condylar regions. Three dimensional finite element analysis was used for this study. FEM model was created by using commercial software, ANSYS(Swanson, Inc., U.S.A.). Fixed model which was fixed on the condylar regions was modeled with 74323 elements and 15387 nodes and spring model which was sprung on the condylar regions was modeled with 75020 elements and 15887 nodes. Six Br${\aa}$nemark implants with 3.75 mm diameter and 13 mm length were incorporated in the models. The placement was 4.4 mm from the midline for the first implant; the other two in each quardrant were 6.5 mm apart. The stress distribution on each model through the designed mandible was evaluated under 500N vertical load, 250N horizontal load linguobuccally, buccal 20 degree 250N oblique load and buccal 45 degree 250N oblique load. The load points were at 0 mm, 10 mm, 20 mm along the cantilever prostheses from the center of the distal fixture. The results were as follows; 1. The stress distribution of condylar regions between two models showed conspicuous differences. Fixed model showed conspicuous stress concentration on the condylar regions than spring model under vertical load only. On the other hand, spring model showed conspicuous stress concentration on the condylar regions than fixed model under 250N horizontal load linguobuccally, buccal 20 degree 250N oblique load and buccal 45 degree 250N oblique load. 2. Fixed model showed stress concentration on the posterior and mesial side of working and balancing condylar necks but spring model showed stress concentration on the posterior and mesial side of working condylar neck and the posterior and lateral side of balancing condylar neck under vertical load. 3. Fixed model showed stress concentration on the posterior and lateral side of working condylar neck and the anterior and mesial side of balancing condylar neck but spring model showed stress concentration on the anterior sides of working and balancing condylar necks under horizontal load linguobuccally. 4. Fixed model showed stress concentration on the posterior side of working condylar neck and the posterior and lateral side of balancing condylar neck but spring model showed stress concentration on the anterior side of working condylar neck and the anterior and lateral side of balancing condylar neck under buccal 20 degree oblique load. 5. Fixed model showed stress concentration on the anterior and lateral side of working condylar neck and the posterior and mesial side of balancing condylar neck but spring model showed stress concentration on the anterior side of working condylar neck and the anterior and lateral side of balancing condylar neck under buccal 45 degree oblique load.. 6. The stress distribution of bone around implants between two models revealed difference slightly. In general, magnitude of Von Mises stress was the greatest at the bone around the most distal implant and the progressive decrease more and more mesially. Under vertical load, the stress values were similar between implant neck and superstructure vertically, besides the greatest on the distal side horizontally. 7. Under horizontal load linguobuccally, buccal 20 degree oblique load and buccal 45 degree oblique load, the stress values were the greatest on the implant neck vertically, and great on the labial and lingual sides horizontally. After all, it was considered that spring model was an indispensable condition for the comprehension of the stress distributions of condylar regions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.12
• /
• pp.1199-1205
• /
• 2012

An empirical acoustic impedance model of acoustic resonators with extended neck at a high sound pressure environment is proposed. The acoustic resonator with extended neck into its cavity is appropriate for the launcher fairing application because the length of neck does not increase the total height of the resonator. This enables one to design slim and light acoustic resonators for launch vehicles. The suggested acoustic impedance model considers the incident pressure and geometric variables(the neck length, the perforation ratio and the hole diameter) in terms of non-dimensional variables. Several acoustic resonators with extended neck are manufactured and their wall impedances are measured according to the pre-defined incident pressure levels. Effects of non-dimensional variables on the non-linear acoustic impedance are investigated so that a simple non-linear impedance model for the launcher fairing application can be proposed. It is demonstrated that the estimated acoustic resistance and acoustic length correction show reasonable agreement with the measured ones within the range of design parameters for launcher fairings.

• The Journal of the Korea Contents Association
• /
• v.20 no.7
• /
• pp.47-55
• /
• 2020

Along with the increased use of smart devices, the incidence of turtle neck syndrome among modern people has increased. Turtle neck syndrome is a posture in which the head is forward compared to the torso due to longer front muscles in the neck and shorter upper muscles, and it is more effective to fix the usual posture habits than surgery or medication. Thus, in this paper, a system is proposed to detect and warn posture that can cause turtle neck syndrome in real time. Image data of correct posture and turtle neck posture are collected to create a CNN-based learning model. Using only the webcam(Built-in camera), the sitting position that enters the camera is verified in real time through the learning model, and if it is a turtle neck position, it generates a warning sound and induces the correct posture. The system can induce people to correct their usual posture habits to treat turtle neck syndrome and prevent more serious diseases such as neck discs.

• Proceedings of the KSLP Conference
• /
• 2011.03a
• /
• pp.14-14
• /
• 2011

• The Journal of Korean Physical Therapy
• /
• v.31 no.1
• /
• pp.24-30
• /
• 2019

Purpose: This study compared the effectiveness of three methods, fascial distortion model (FDM), myofascial release (MFR), self-myofascial release (SMR), on the neck range of motion and pain. Methods: In this study, the collected data were processed statistically using SPSS version 22.0 for Windows. Descriptive statistics were used to analyze the general characteristics of the subjects. Repeated measure ANOVA was conducted to analyze the range of motion of the neck of the group and VAS, and Contras was used to see the difference in significance over time. One-way ANOVA was used to compare the differences among the groups and a post-hoc test was used. The significance level (${\alpha}$) was 0.05. Results: In the range of motion, the flexion and extension of the neck, right rotation, and left rotation were significantly different in the SMR, FDM, and MFR groups. The right lateral flexion showed significant differences in the FDM, MFR, and SMR groups. The VAS was similar in the groups at 2 and 4 weeks, but there was a significant difference among the FDM, MFR, and SMR groups at 6 weeks. Conclusion: In this study, MFR and MSR as well as FDM were effective in controlling the range of motion and pain control of the neck. Further studies will be needed to determine the effects of long-lasting treatments other than pain control. These studies and the present study will be used as a basis for ongoing research into the duration and method of application for musculoskeletal therapies.

• The Journal of Korean Physical Therapy
• /
• v.21 no.3
• /
• pp.1-8
• /
• 2009

Purpose: The purpose of this study was to examine the functional category, the item structure and the model-data fit of the neck disability index (NDI) of neck pain subjects by performing a Rasch rating scale analysis. Methods: The data was obtained from the assessments of 71 college students (males: 27, females: 44) with neck pain. The data of the NDI was applied to the Rasch's rating scale model to estimate the difficulty of items, the goodness-of-fit of each item, the separation reliability and index, and the rating scale. Results: The 'sleep' item showed misfit and nine items were founds to be fits for self-reporting of disability due to neck pain. The most difficult item of the remaining 9 items was 'work' and the easiest item was 'headache'. The transformation formula score=(logit score+7.10)/(7.10+0.11)$\times$100. The 6 response levels of the NDI were validated according to the structure of the rating scale. The item and subject reliability of the separation reliability was 0.97 and 0.85, respectively. Conclusion: We proved that the NDI for self-reporting of disability of daily activities due to mild neck pain was valid and reliable. This study suggests that individuals with mild neck pain may be assessed by using the modified NDI that does not include the 'sleep' item in the 10 items of NDI.

• Journal of Mechanical Science and Technology
• /
• v.14 no.3
• /
• pp.338-349
• /
• 2000

Neck muscle forces and spinal loads at the C4/5 level were estimated that result from isometric voluntary ramp efforts gradually developing to maximums in flexion, extension, left lateral bending and right lateral bending. Electromyographic (EMG) activities, a three-dimensional anatomic data of the neck and a hybrid model, EMG-assisted optimization (EMGAO) model, were used. The model computed the cervical loads at 25%,50%,75%, and 100% of peak moments. The highest model-predicted C4/5 joint compressive forces occurred during flexion; $361\;({\pm}164)\;N,\;811\;({\pm}288)\;N,\;1207\;({\pm}491)\;N\;and\;1674\;({\pm}319)\;N$ in 25%, 50%, 75% and 100% of peak moment respectively. Variations in load distribution among the agonistic muscles and co-contractions of antagonistic muscles were estimated during ramp efforts. Results suggest that higher C4/5 joint loads than previously reported are possible during isometric, voluntary muscle contractions. These higher physiological loads at C4/5 level must be considered possible during orthopedic reconstruction at this level.

• Proceedings of the KSLP Conference
• /
• 2012.03a
• /
• pp.23-23
• /
• 2012