• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2002.05a
• /
• pp.25-27
• /
• 2002

Most of automotive companies make use of spot welding in order to assemble car body. Even though spot welding has been developed for last 60 years, there were some limitations in upgrading production line. Laser welding has advantages In productivity and degree of freedom in design. Thanks to fast speed, we can reduce body assembly line by 80%. Also with non-contact & one-side approach, it is possible to design various car body structures. New project launched the laser welding technology in mass production has started in 1999. In this paper, a new type of cur named 'next generation vehicle (NGV)' is introduced. The car body of NGV is welded with 4㎾ Nd: YAG laser.

• Journal of Welding and Joining
• /
• v.27 no.2
• /
• pp.69-75
• /
• 2009

The effects of welding speed were investigated on penetration characteristics, defects and mechanical properties including formability test in Nd:YAG laser welded 1000MPa grade DP steels. A shielding gas was not used and bead-on-plate welding was performed with various welding speeds at 3.5kW laser power. Defects of surface and inner beads were not observed in all welding speeds. As the welding speed increased, the weld cross-section varied from the trapezoid having wider bottom bead, through X type, finally to V type in partial penetration range of welding speeds. The characteristic of hardness distribution was also investigated. The center of HAZ had maximum hardness, followed by a slight decrease of hardness as approaching to FZ. Significant softening occurred at the HAZ near BM. Regardless of the welding speed, the weld showed approximately the same hardness distribution. In the perpendicular tensile test with respect to the weld direction, all specimens were fractured at the softening zone. In the parallel tensile test to the weld direction, the first crack occurred at weld center and then propagated into the weld. Good formability over 80% was taken for all welding conditions.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.434-439
• /
• 2011

There are about 2.4million disabled in Korea, 2009. Also, Korean society entered into an aging society. Therefore disable and elderly are getting more involved in our society. This study proposes simple ramp design for wheel chair users and welding method and condition for manufacturing. In the middle of ramp, screw jack and motor are installed so that ramp can be moved left and right side. To make the ramp moves easily, ramp was fixed by installing LM guide on both sides. Ramp production for using Nd:YAG laser certain dissimilar welding in stainless steel sheet and cold reduced carbon steel. The output was fixed by 3kW, the speed was increased to 2~7m/min, Argon was used as shielding gas and the flow rate was changed to 10~30L/min. The proper welding condition is the output 3kW and welding speed 2~5m/min.

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.256-257
• /
• 2002

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.193-194
• /
• 2007

• Journal of Welding and Joining
• /
• v.25 no.4
• /
• pp.65-71
• /
• 2007

Laser weldability of the aluminized steel for the full penetration welding will be described in this paper. We focused on the effect of Al coating conditions on weld strength. For these objectives, aluminized steel sheets that have various thickness and coating weight were prepared for laser welding. And then, tensile-shear and hardness test were carried out. At the same time, Al contents in weld after laser welding were analyzed and their correlations with mechanical properties were investigated. Besides, as removing partially coating layer, weldability has been investigated according to the position of coating layer. As a result of this study, tensile-shear strength was decreased with increasing Al contents in weld, and Al of coating layer caused grain growth.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.216-218
• /
• 2006

The application of aluminium alloy is increasing for lightweight and high quality transport vehicle. In this study, therefore, it is intended to apply the high speed hybrid welding method for marine grade aluminium alloy(A5083) used for shipbuilding that consists of 3 kW CW Nd:YAG laser and MIG welding process. For this purpose, the characteristics of process parameters(laser & arc combine angle and focal position of hybrid head to specimen) are investigated for hybrid fillet joint. This study also describes determination of heat distribution using finite element model of the T-joint fillet weld using the in-house solver which has been validated for different type of welding problems.

• Journal of Welding and Joining
• /
• v.29 no.3
• /
• pp.82-88
• /
• 2011

With a tendency for the application of thin magnesium alloy plates in portable electronic equipment such as cell phone and notebook PC, there is a requirement to develop a welding technology for the lap welding of these thin magnesium alloy. This paper presents the single pulsed laser welding of AZ31B magnesium alloy. The effects of fiber types and parameters such as peak power and pulse width on laser weldability were investigated. The results show that weld defects, especially solidification crack, were always generated in the weld. These defects couldn't be controlled by the simple square pulse, but could be improved through the application of variable pulse. It is because that variable pulse has effect of solidification delay by dropping peak power gradually.

• Journal of Welding and Joining
• /
• v.31 no.4
• /
• pp.28-33
• /
• 2013

The effects of laser welding beam quality is very large. However, not an analysing case was found for the difference on the plasma emission signal during laser welding according to the beam quality. Therefore, in this study, we compared and evaluated penetration and signal change according to the beam quality at the a similar wavelength band by using a fiber laser and Nd:YAG laser. In addition, we took high speed videography in order to make sure that FFT analysis reflects the actual motion period of keyhole and found the period of video analysis and FFT mostly matched. As a result, it is expected to secure higher reliability than evaluating signal intensity when appling FFT to monitoring.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.199-202
• /
• 2007

The center floor is a part of underbody of cars. The assembling method is mostly a resistant spot welding. But the resistant spot welding has many demerits in productivity such as low welding speed, large spatter occurring, hard to verify the welding quality. The laser welding has many merits such as high welding speed, high static and dynamic weld strength. So the laser welding has been studied to substituted the resistant spot welding. Therefore, in this study, as a pre-evaluation stage for replacing the resistance spot welding with laser in production of automobile parts, the weldability of cold rolled and zinc coated steel sheets is studied and also evaluated the weld strength by the tensile shear test. And the shape of weld bead appearances and micro structure of the weld bead section is also evaluated.