• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.213-214
• /
• 2008

The $Sr_{0.7}Bi_{2.3}Nb_2O_9$(SBN) thin films are deposited on Pt-coated electrode(Pt/Ti/SiO2/Si) using RF sputtering method at various substrate temperature. The optimum conditions of RF power and Ar/O2 ratio were 60[W] and 70/30, respectively. The crystallinity of SBN thin films were increased with increase of substrate temperature in the temperature range of 100~400[$^{\circ}C$]. The capacitance of SBN thin films were increased with the increase of substrate temperature.

• Nuclear Engineering and Technology
• /
• v.32 no.4
• /
• pp.372-378
• /
• 2000

The effect of alloying elements on the creep resistance of Zr alloys was investigated using thermal creep tests that were performed as a part of advanced fuel cladding development. The creep tests were conducted at 40$0^{\circ}C$ and 150 MPa for 240 hr. A statistical model was derived from the relationship between the steady-state creep rate and the content of individual alloying elements. The creep strengthening effect decreased in the following sequence : Nb, Sn, Mn, Cr, Mo, Fe and Cu. The high creep resistance of Sn and the opposite effect of Fe on zirconium alloys seem to be associated with their lowering and enhancing, respectively, the self-diffusivity of the zirconium matrix.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.142-147
• /
• 1998

핵연료피복관의 부식성능은 합금원소의 조성에 매우 민감하지만 열처리변수에 따라서도 크게 좌우되므로 열처리변수가 Zr 신합금의 부식저항성과 미세조직에 미치는 영향을 조사하였다. Zr-Nb-Sn-Fe-Cr 조성을 갖는 합금을 제조하여 열처리면수($\Sigma$A)를 7.7x$10^{-l9}$~5.3x$10^{-17}$ hr로 제어한 후 400 $^{\circ}C$/10.3 MPa 분위기의 autoclave를 이용하여 부식시험을 실시 하였다. 열처리변수($\Sigma$A)가 증가함에 따라서 부식저항성은 감소하였으며 열처리변수의 값이 7.7x$10^{-l9}$와 8.8x$10^{-l9}$ hr일 때 부식저항성은 매우 우수하였다. 천이후 부식속도에 미치는 열처리변수의 영향은 무게증가량에 미치는 영향과 동일한 경향을 나타냈으며 $\Sigma$A가 1.0x$10^{-18}$ hr이하에서 매우 낮은 부식속도를 보였다. 석출물 크기의 증가는 부식저항성을 감소시키는 것으로 관찰되었다. 따라서 우수한 부식저항성을 갖는 Zr 신합금을 개발하기 위해서는 중간 열처리 온도를 적절히 조절하여 석출물의 크기를 0.05 $\mu$m이하로 제어하여야 한다.다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.262-271
• /
• 1999

This work was intended to modify the solidification structure of high speed steel roll material for hot strip mill, by the introduction of alloying elements designed to form primary carbide dispersions via melt treatment procedure. Solidification structure was modified by the melt treatment with titanium and distribution. This modifying effect could be attributed to the fact that the nuclie formed at high temperature upon inoculation induce the formation of fine equiaxed grain and primary carbide during solification, which is also likely to be responsible for the fact that TiC acts as effective nuclie for primary VC solidification.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.383-389
• /
• 1999

The purpose of this study was to investigate the effects of alloying and rolling condition on the mechanical properties and to develop high strength line pipe steels with good toughness. Tests were carried out by the laboratory experiments followed by mill trials and mass production. It was found that a small addition of microalloying elements, such as Nb, V with Mo or Ti remarkably increased the strength and toughness of hot strips. The optimum condition of thermomechanical rolling on low carbon microalloyed steel improved the toughness through the formation of a fine and uniform microstructure. Based on this mill trials following the fundamental research, the production technology of line pipe steels, grade X70∼X100 with high toughness, has been established. These grade steels exhibit excellent low temperature toughness (vTs= under -80$^{\circ}C$) and sufficient strength in both the base metal and the ERW seam weld position, respectively.

• Journal of Sericultural and Entomological Science
• /
• v.41 no.2
• /
• pp.94-101
• /
• 1999

Twelve pure silkworm lines identified based in higher G.C.A values from a line${\times}$Tecter crossing programme, were crossed with twelve breeds showing cocoon shell ratio>22% and hybrids prepared, evaluated in a Multiple index method. Seven hydrids showing average index value>50 in all the 10 economic characters were seclcted and evaluated in the laboratory. However, two hybrids viz., A3${\times}$935E and A3${\times}$916B were finally selected based on the superiority of the breeds in one day shorter larval duration and with and with higher reeling characters compared to control KA${\times}$NB4D2. The breeding procedure involed in evolution hybrids are discussed.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1929-1931
• /
• 1996

In this work, it is proposed new PD(partial discharge) detection technique using electro-optic effect, for which partial discharges generated from needle-plane electrode in air were detected through optical measuring system by use of $LiNbO3_3$ electro-optic crystal. As a result, it is noticed that PD measurable phase intervals are limited by the asymmetrical D-E hysteresis loop of the crystal with defects and half-wave voltage. However, both number of measured PD pulses and their amplitude were increased with applied voltage, which likely implies that it is possible to detect PD through newly proposed electro-optic method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.292-295
• /
• 2001

The NdBaCuO superconducting samples were prepared by the Zone melting under low oxygen partial pressure. After the zone-melting the oxygenation process of the NdBaCuO samples in a oxygen flow furnace was studied. In order to compare the oxygenation condition the sintering NdBaCuO samples were studied also. In the study it is found that the optimum temperature for the oxygenation is $350^{\circ}C$, and the oxygen flow speed, the sample volume and the surface area of the sample would influence the oxygenation and the oxygen content.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.201-203
• /
• 2005

A kinetic model for particle coarsening behavior in the weld heat affected zone (HAZ) was proposed. Unlike the conventional approach, where the mean-sized particle is considered to grow continuously, the proposed model considered the critical particle size which can be derived from the Gibbs-Thomson equation. In this study, the proposed particle coarsening model was applied to study the behavior of (Ti, Nb )(C, N) complex particle in the weld HAZ. The predicted particle size distributions using the proposed model were in agreement with the experimental results.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.39-41
• /
• 2007

In this study, actual scale welding were conducted at the USC thermal power plant turbine and main steam pipe casting candidate mock up material 9Cr-1.5Mo-CoVNbNB steel(CB2) and 9Cr-0.5Mo-MVNbN steel(P92). And to evaluate the welding process for the actual production, mechanical property testes were conducted for the weld metal. The Mock-up welding condition successfully led to an excellent structural welding joint between casting and pipe material.