• Journal of Dental Rehabilitation and Applied Science
• /
• v.21 no.1
• /
• pp.33-42
• /
• 2005

This study was performed to investigate the surface properties and in vitro biocompatibility of electrochemically oxidized Ti-6Al-7Nb alloy by anodic spark discharge technique. Discs of Ti-6Al-7Nb alloy of 20 mm in diameter and 2 mm in thickness were polished sequentially from #300 to 1000 SiC paper, ultrasonically washed with acetone and distilled water for 5 min, and dried in an oven at $50^{\circ}C$ for 24 hours. Anodizing was performed using a regulated DC power supply. The applied voltages were given at 240, 280, 320, and 360 V and current density of $30mA/cm^2$. Hydrothermal treatment was conducted by high pressure steam at $300^{\circ}C$ for 2 hours using a autoclave. Samples were soaked in the Hanks' solution with pH 7.4 at $36.5^{\circ}C$ during 30 days. The results obtained were summarized as follows; 1. The oxide films were porous with pore size of $1{\sim}5{\mu}m$. The size of micropores increased with increasing the spark forming voltage. 2. The main crystal structure of the anodic oxide film was anatase type as analyzed with thin-film X-ray diffractometery. 3. Needle-like hydroxyapatite (HA) crystals were observed on anodic oxide films after hydrothermal treatment at $300^{\circ}C$ for 2 hours. The precipitation of HA crystals was accelerated with increasing the spark forming voltage. 4. The precipitation of the fine asperity-like HA crystals were observed after being immersed in Hanks' solution at $37^{\circ}C$. The precipitation of HA crystals was accelerated with increasing the spark forming voltage and the time of immersion in Hanks' solution. 5. The Ca/P ratio of the precipitated HA layer was equivalent to that of HA crystal as increasing the spark forming voltage and the time of immersion in Hanks' solution.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.22 no.1
• /
• pp.101-110
• /
• 2006

This study was performed to investigate the surface properties and in vitro biocompatibility of electrochemically oxidized Ti-6Al-7Nb alloy by anodic spark discharge technique. Discs of Ti-6Al-7Nb alloy of 20 mm in diameter and 2 mm in thickness were polished sequentially from #300 to 1000 SiC paper, ultrasonically washed with acetone and distilled water for 5 min, and dried in an oven at $50^{\circ}C$ for 24 hours. Anodizing was performed using a regulated DC power supply. The applied voltages were given at 240, 280, 320, and 360 V and current density of $30mA/cm^2$. Hydrothermal treatment was conducted by high pressure steam at $300^{\circ}C$ for 2 hours using a autoclave. Samples were soaked in the Hanks' solution with pH 7.4 at $36.5^{\circ}C$ during 30 days. The results obtained were summarized as follows; 1. The oxide films were porous with pore size of $1{\sim}5{\mu}m$. The size of micropores increased with increasing the spark forming voltage. 2. The main crystal structure of the anodic oxide film was anatase type as analyzed with thin-film X-ray diffractometery. 3. Needle-like hydroxyapatie (HA) crystals were observed on anodic oxide films after hydrothermal treatment at $300^{\circ}C$ for 2 hours. The precipitation of HA crystals was accelerated with increasing the spark forming voltage. 4. The precipitation of the fine asperity-like HA crystals were observed after being immersed in Hanks' solution at $37^{\circ}C$. The precipitation of HA crystals was accelerated with increasing the spark forming voltage and the time of immersion in Hanks' solution. 5. The Ca/P ration of the precipitated HA layer was equivalent to that of HA crystal as increasing the spark forming voltage and the time of immersion in Hanks' solution.

• Journal of the Korean Magnetics Society
• /
• v.2 no.2
• /
• pp.91-98
• /
• 1992

In a $Co_{67}Fe_{4.5}Nb_{2}Si_{10}B_{15}$ amorphous alloy ribbon the effect to two-step annealing on the soft magnetic properties has been studied. By two-step annealing method which the second annealing at low temperature of $310^{\circ}C$ for 2 hours is undertaken after the primary annealing at high temperature above $480^{\circ}C$ for 20 minutes at the vacuum state, the coercive force and the squareness are not changed nearly but the initial permeability at d.c. and the effective permeability at a.c. are remark-ably increased compared with the one-step annealing. The maxima of the initial permeability and the effective permeability at 1 kHz after the two-step annealing are 290,000 and 41,000, respectively, which are 30% higher than those of the one-step annealing. The change of magnetic properties with annealing temperature is discussed in terms of the residual stress, the domain size, the cluster and the crystalline phase.

• Proceedings of the Korean Fiber Society Conference
• /
• 1996.10a
• /
• pp.124-130
• /
• 1996

The hydrocarbons containing more than 10 carbons(0.1% of total volume, C10+), residue of aromatization from aliphatic hydrocarbons, were condensated in the presence of catalyst aluminumchloride and cocatalyst nitrobenzene(NB) to be pitchs with desirable properties. The properties of pitch were affected by the concentration of cocatalyst chosen 20 and 30wt.%. The pitch with 30wt.% NB showed higher carbon yield and lower crystallinity than that with 20wt.% NB. The two pitches were heat treated at 1000C and measured of charge/discharge capacity of the carbon as an anode. The carbon prepared at 20wt.% NB exhibited excellent cyclic stability with a capacity of 218mAh/.g and that at 30wt.% exhibited rather low cyclic stability with higher capacity of 235mAh/g.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.696-700
• /
• 2012

(Na, K) $NbO_3$ thick film was successfully achieved using a sol-gel coating process with the addition of polyvinylpyrrolidone (PVP) to a metal alkoxide solution. The transparent coating solution, mixed with Nb:PVP = 1:1 in a molar ration, was synthesized by evaporating the solvent to over 62.5 wt%. Additive PVP increased the viscosity of the solution so that the coating thickness could be enhanced. The thickness of the (Na, K) $NbO_3$ film assisted by PVP was ca. 320 nm at the time of deposition; this value is four times thicker than that of the sample fabricated without PVP. Also, due to PVP binding with the OH groups of the metal alkoxide, the condensation reaction in the film was suppressed. The crystalline size of the (Na, K) $NbO_3$ films assisted by PVP was ca. 15 nm smaller than that of the film fabricated without PVP. After the sintering process at $700^{\circ}C$, the (Na, K) $NbO_3$ films were mainly composed of randomly oriented (Na, K) $NbO_3$ phase of perovskite crystal structure, including a somewhat secondary phase of $K_2Nb_4O_{11}$. However, by adding PVP, the content of the secondary phase became quite smaller than that of the sample without PVP. It was thought that the addition of PVP might have the effect of restraining the loss of potassium and that PVP could hold metalloxane by strong hydrogen bonding before complete decomposition. Therefore, the film thickness of the (Na, K) $NbO_3$ films could be considerably advanced and made more crack-free by the addition of PVP.

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.478-486
• /
• 1995

Cu/NbTi multilayer thin films and superconducting wires were fabricated and heat treated with conventional annealing and analyzed by differential scanning calorimetry (DSC) as a basic study for the enhancement of Jc. Interfacial reactions of Cu/NbTi multilayer thin films and superconducting wires were investigated with optical microscope, SEM, and XRD. According to the effective heat of formation (EHF) model, CU$\_$3/Ti was predicted as a first phase. However, considering the crystalline structure and thermodynamics, CuTi was predicted as a first phase. According to the results of DSC and XRD, CU$\_$2/Ti was found to be the first phase, followed by the formation Of CU$\_$4/Ti. The difference in first crystalline phase between the experimental result and the predicted one was discussed. In case of Cu/NbTi superconducting wires, the compounds formed at the Cu/NbTi interface grew with annealing time and the amount of compounds formed in Nb-47wt%Ti alloy was larger than that in Nb-50wt%Ti alloy. It seemed that the incubation time for the formation of compounds in Nb-50wt%Ti alloy was longer than that formed in Nb-47wt%Ti alloy. Also, the diffusion was the rate controlling step for the growth of compounds in all specimens. These compounds were formed at 500-600.deg. C for I hour annealing and, thus, the drawing time below I hour must be required to minimize the growth of compounds for the enhancement of Jc.

• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.17-24
• /
• 2011

To investigate the relationship between heat treatment in zirconium alloy tubing process and metallurgical characteristics of Zr-1Nb-0.69Sn-0.11Fe alloy tubes, mechanical and oxidation behaviors of tubes heat treated at different temperatures after the final pilgering were investigated. The stress strain curves exhibited the saturation behaviors in all heat treatment conditions ($460{\sim}600^{\circ}C$) in this study with the onset strain of saturation increased with increase of post-pilgering annealing temperature. The strength fell off rapidly with increasing annealing temperature. The ultimate strength of the low tin Zr-1Nb-0.69Sn-0.11Fe alloy with slightly higher iron and oxygen contents in this study was found to be higher than Zr-1Nb-1Sn-0.1Fe alloy. The oxidation experiments in steam condition revealed that the corrosion resistance of low tin Zr-1Nb-0.69Sn-0.11Fe alloy was better than the Zr-1Nb-1Sn-0.1Fe alloy with a higher Sn content. The weight gain of low tin Zr-1Nb-0.69Sn-0.11Fe alloy tubes gradually increased with the increasing annealing temperature possibly due to the decreased Nb content in the matrix because of the formation of ${\beta}-Nb$ particles.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.79-85
• /
• 2023

A novel low-temperature co-fired ceramic (LTCC) dielectric, composed of (1-4x)Bi_1.5Zn_1.0Nb_1.5O₇-3xBi₂Zn_2/3Nb_4/3O₇-2xLiZnNbO₄ (x=0.03-0.21), was synthesized through reactive liquid phase sintering of Bi_1.5Zn_1.0Nb_1.5O₇-xLi₂CO₃ ceramic at temperatures ranging from 850℃ to 920℃ for 4 hours. During sintering, Li₂CO₃ reacted with Bi_1.5Zn_1.0Nb_1.5O₇, resulting in the formation of Bi₂Zn_2/3Nb_4/3O₇, and LiZnNbO₄. The resulting sintered body exhibited a relative sintering density exceeding 96% of the theoretical density. By altering the initial Li₂CO₃ content (x) and consequently modulating the volume fraction of Bi_1.5Zn_1.0Nb_1.5O₇, Bi₂Zn_2/3Nb_4/3O₇, and LiZnNbO₄ in the final sintered body, a sample with high dielectric constant (ε_r), low dielectric loss (tan δ), and the temperature coefficient of dielectric constant (TCε) characterized by NP0 specification (TCε ≤ ±30 ppm/℃) was achieved. As the Li₂CO₃ content increased from x=0.03 mol to x=0.15 mol, the volume fraction of Bi₂Zn_2/3Nb_4/3O₇ and LiZnNbO₄ in the composite increased, while the volume fraction of Bi_1.5Zn_1.0Nb_1.5O₇ decreased. Consequently, the dielectric constant (εr) of the composite materials varied from 148.38 to 126.99, the dielectric loss (tan δ) shifted from 5.29×10^-4 to 3.31×10^-4, and the temperature coefficient of dielectric constant (TCε) transitioned from -340.35 ppm/℃ to 299.67 ppm/℃. A dielectric exhibiting NP0 characteristics was achieved at x=0.09 for Li₂CO₃, with a dielectric constant (ε_r) of 143.06, a dielectric loss (tan δ) value of 4.31×10^-4, and a temperature coefficient of dielectric constant (TCε) value of -9.98 ppm/℃. Chemical compatibility experiment with Ag electrode revealed that the developed composite material exhibited no reactivity with the Ag electrode during the co-firing process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.806-809
• /
• 2013

In this study, $(Na_{0.525}K_{0.443}Li_{0.037})(Nb_{0.883}Sb_{0.08}Ta_{0.037})O_3+0.10\;wt%Bi_2O_3+0.35\;wt%B_2O_3$ ceramics were prepared by conventional soild-state sintering process. The specimens were sintered at temperature range from $1,060^{\circ}C$ to $1,100^{\circ}C$. XRD (X-ray diffractron), SEM (scanning electron microscope) were used to analyze the crystal structure and microstructural sproperties of specimens. And also, $T_{O-T}$, TC were observed by the mesurement of temperature dependence of dielectric constant. Excellect physical properties of the piezoelectric constant $d_{33}$= 170 pC/N, electromechanical coupling factor kp= 0.312, Tc= $315^{\circ}C$ were obtained, respectively, from the specimen sintered at $1,080^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.41 no.3
• /
• pp.235-240
• /
• 2021

We present the effect of the critical cooling rate during rapid solidification on the nucleation of precipitates in an Fe₇₅B₁₃P₅Nb₂Hf₁C₄ (at.%) alloy. The thermophysical properties of the rapidly solidified Fe₇₅B₁₃P₅Nb₂Hf₁C₄ liquids, which were obtained at various cooling rates with various sizes of gas-atomized powder during a high-pressure inert gas-atomization process, were evaluated. The cooling rate of the small-particle powder (≤20 ㎛) was 8.4×10⁵ K/s, which was 13.5 times faster than that of the large-particle powder (20 to 45 mm; 6.2×10⁴ K/s) under an atomized temperature. A thermodynamic calculation model used to predict the nucleation of the precipitates was confirmed by the microstructural observation of MC-type carbide in the Fe₇₅B₁₃P₅Nb₂Hf₁C₄ alloy. The primary carbide phase was only formed in the large-particle gas-atomized powder obtained during solidification at a slow cooling rate compared to that of the small-particle powder.