• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.213-216
• /
• 1995

Strontium niobate, $Sr_2Nb_2O_{7}$ was prepared by the molten stilt synthesis (MSS) and the chemical coprecipitation method (CCP). Single phase $Sr_2Nb_2O_{7}$ was obtained by MSS and CCP at $750^{\circ}C$ and $800^{\circ}C$, respectively. An intermediate phase of composition, $Sr_{5}Nb_4O_{15}$, appeared at $700^{\circ}C$ when CCP method was employed. The resulting powder was observed to have finer particles and more uniform distribution of particle sizes, as compared to those obtained through the conventional method. Such powder characteristics allowed the use of a much lower sintering temperature of $1400^{\circ}C$. Grain-orientation along (0k0) direction, which is advantageous for improving dielectric properties, was also observed. The sintering characteristics and the dielectric properties prepared by MSS and CCP, were better than those by the conventional method.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1411-1413
• /
• 2001

The $(Ba_{0.5}Sr_{0.5})(Nb_{0.5}Ti_{0.5})O_3$ [BSNT] ceramics were prepared by conventional mixed oxide method. The structural properties of the BSNT ceramics with sintering temperature were investigated by XRD, SEM, EDS. Increasing the sintering temperature, diffraction intensity of the BST(110) peak was increased. The average grain size of BSNT ceramics were increased with sintering temperature. In the case of BSNT ceramics sintered at 1550$^{\circ}C$, the grain was uniform and the pore was not existed. Increasing the sintering temperature from 1400$^{\circ}C$ to 1500$^{\circ}C$, the amount of Nb and Sr were decreased. The density of BSNT ceramics sintered at 1550$^{\circ}C$ was $1.125g/cm^2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.873-877
• /
• 2007

In order to apply a complex multilayer chip LC filter, this study has estimated the interfacial reaction and coupling properties of dielectric materials $Pb(Fe_{1/2}Nb_{1/2})O_3$ and Ni-Zn-Cu ferrite materials through low-temperature co-sintering (LTCS). PFN powders were fabricated using double calcinated at $700^{\circ}C$ and then $850^{\circ}C$. While the perovskite phase rate was found to be 91 %, after heat treatment at $900^{\circ}C$ for 6h, the perovskite phase rate and density exhibited a value of 100 % and 7.46$g/cm^3$, respectively. The PFN/Ni-Zn-Cu ferrite, PFN/CUO (or $Pb_2Fe_2O_5$) and ferrite/CuO (or $Pb_2Fe_2O_5$) were mechanically coupled through interfacial reactions after the specimen was co-sintered at $900^{\circ}C$ for 6 h. No intermediate layer exists for the mutual coupling reaction. This result indicates the possibility of low-temperature co-sintering without any interfacial reaction layer for a multilayer chip LC filter.

• Journal of Technologic Dentistry
• /
• v.28 no.1
• /
• pp.19-26
• /
• 2006

The effect of Nb on interfacial bonding characteristics of Ni-Cr alloy for porcelain fused to metal crown (PFM) has been studied in order to investigate oxide layer. A specimens of Ni-Cr alloy, which is 0.8mm in thickness, within the porcelain furnace of 1,000$^{\circ}C$ with four tests such as air, vacuum, air for 5 minutes and vacuum for 5 minutes in order to examine an oxide behavior of alloy surface generated by the adding of Nb to be controlled at a rate of 0, 1, 3 and 5. Oxide film was observed form of the fired specimens with scanning electron microscope (SEM), and at the same time it measured Electron Probe Micro Analyzer (EPMA). The result of this study were as follows: 1. Cr oxide film and Nb oxide film were observed from the surface of specimen to be controlled at a rate of Nb 1%. 2. Nb oxide film was observed from the interface of specimens to be controlled at a rate of Nb 1% and 3%. 3. The stability of oxide films that treated in air were more stable than treated under vacuum.

• Journal of Korea Foundry Society
• /
• v.23 no.4
• /
• pp.204-211
• /
• 2003

Ti-3wt.%Nb(${\alpha}$type), Ti-20wt.%Nb(${\alpha}+{\beta}$,type) and Ti-40wt.%Nb(${\beta}$type) alloys were melted by vacuum are remelting. The specimens were homogenized at 1050$^{\circ}C$ for 24 hr and were then hot rolled to 50% reduction. Each alloys were solution heat treated at ${\beta}$ zone and ${\alpha}+{\beta}$, zone after homogenization, and then aged. The microstructural and hardness changes in Ti-Nb alloys with Nb contents were investigated by SEM, XRD and hardness tester. The microstructural change from equiaxied to acicular and the increase of ${\beta}$ phase in Ti-Nb alloys were obtained when the Nb content increased. The higher hardness value of ${\alpha}+{\beta}$type alloy was obtained compared to the other alloys.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.3
• /
• pp.30-34
• /
• 2022

Effects of electron beam (EB) irradiation on the mechanical strength of Cu (conducting sheath) and Nb (diffusion barrier) of Cu/Nb/MgB₂ superconducting was investigated. Wire- and tape-type Cu/Nb/MgB₂ samples were irradiated at E-beam energy of 2.5 MeV and 5 mA and a maximum E-beam dose was 5×10¹⁷ e/m². The hardness value of Cu and Nb region was measured by the Vickers micro-hardness method. In the case of the wire sample, the hardness of Cu and Nb increased proportionally as the dose was increased up to 5×10¹⁷ e/m², whereas in the case of the tape sample, the hardness increased up to a dose of 0.5×10¹⁷ e/m², and decreased slightly 5×10¹⁷ e/m². The hardness increase of Cu and Nb is believed to be due to the decrease of the deformability of Cu and Nb due to the defects formed inside the materials by E-beam irradiation.

• Journal of the Korean Ceramic Society
• /
• v.41 no.10 s.269
• /
• pp.783-787
• /
• 2004

Microwave dielectric properties and the microstructure of $Ba_5Nb_4O_{15}$ ceramics with $PbO-B_2O_3-SiO_2$ glass frit were investigated to reduce the sintering temperature of $Ba_5Nb_4O_{15}$ ceramics as a function of the amount of glass frit from $0.5wt\%$ to $10wt\%$ and the sintering condition. The sintered density and the microwave dielectric properties of $Ba_5Nb_4O_{15}$ ceramics were remarkably changed with the amount of glass fit which existed as a liquid phase and assisted the densification. $Ba_5Nb_4O_{15}$ with $3wt\%$ $PbO-B_2O_3-SiO_2$ glass frit sintered at $900^{\circ}C$ for 2 h showed dielectric constant (K) of 41.4, a quality factor (Q $\times$f) of 13,485 GHz, and a Temperature Coefficient of resonant Frequency (TCF) of 9 ppm/$^{\circ}C$. Due to no trace of physical and chemical reaction between this composition and Ag electrode cofired at $900^{\circ}C$ for 2 h, this ceramics can be a good candidate for the multilayer dielectric filter.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1025-1031
• /
• 1999

Alloys of TiAl with six different compositions. i. e., Ti-(42, 44)Al-2Nb-4V. Ti-(42, 44)Al-4Nb-2V and Ti -(42, 44)Al-4Nb-2Cr, were manufactured by arc-melting. and their oxidation behavior was studied. Both isothermal and cyclic oxidation tests were performed at 700, 800 and $900^{\circ}C$ in air for 50hr. The oxidation resistance increased in the order of Ti-(42, 44)Al-2Nb-4V, Ti-(42, 44)Al-4Nb-ZV and Ti-(42, 44)Al-4Nb-2Cr. It was found that V was a deleterious element, while Cr was a beneficial element in terms of oxidation resistance. During oxidation, a simultaneous interdiffusion was observed. All the constituent elements in the base alloys diffused outward. whereas oxygen from the atmosphere diffused inward, to form triple oxide layers composed of an outermost $\textrm{TiO}_2$ layer. upper ($\textrm{TiO}_2+\textrm{Al}_2\textrm{O}_3$) mixed layer, and lower $\textrm{TiO}_2$-rich layer.

• Korean Journal of Materials Research
• /
• v.13 no.11
• /
• pp.761-768
• /
• 2003

The corrosion resistance and cytotoxicity behavior of Ti alloys were studied as a function of Nb contents(3wt.%Nb, 20wt.%Nb, 40wt.%Nb). Ti-Nb alloys were melted by vacuum arc furnace and then rolled to 50% reduction ratio after homogenized at 105$0^{\circ}C$ for 24hrs. The corrosion resistance of Ti-Nb alloys were investigated by potentiodynamic polarization test in the 0.9% NaCl and 5% HCI solution. Biocompatibility of Ti-Nb alloys was evaluated by cytotoxicity test. The results can be summarized as follows 1) The microstructure change from equiaxial to acicular and the increased $\beta$ phase in Ti-Nb alloys were obtained as the Nb content increased. 2) For the corrosion test in the solution of 0.9% NaCl and 5% HCI, the corrosion behavior of Ti-Nb alloys was similar to ASTM grade 2 CP Ti. 3) For the cytotoxicity test, Ti-Nb alloys showed excellent biocompatibility compared to ASTM grade 2 CP Ti, 316L STS and Co-Cr alloys.

• Journal of the Microelectronics and Packaging Society
• /
• v.2 no.2
• /
• pp.31-40
• /
• 1995

Donor dopant로 WO3, Ta2O5 및 Nb2O5를 첨가한 Zr0.8Sn0.2TiO4 세라믹스의 유전상수 $\varepsilon$r 품 질계수 Q 및 공진주파수의 온도계수 rf에 대하여 연구하였다. 139$0^{\circ}C$에서 32시간 소결시 donor dopant 첨가량에 따른 ZST의 유전상수는 소결밀도의 변화 거동과 잘 일치하였다. 5.5 GHz에서 측정 한 ZST의 품질계수 Q는 ~0.5 mol% WO3 Ta2O5 및 Nb2O5 첨가에 의해 6800에서 8500 정도로 증가 하였다. ZST의 $\tau$f는 0.3 mol%까지의 WO3 첨가량 증가에 따라 0 ppm/$^{\circ}C$에서 -4.6 ppm/$^{\circ}C$까지 음 의 값으로 직선적으로 감소하였으며 0.4 mol% 범위의 Ta2O5 및 Nb2O5 첨가에 의해 -7 ppm/$^{\circ}C$ 까지 직선적으로 감소하였다.