• Journal of Information Technology Services
• /
• v.10 no.4
• /
• pp.259-268
• /
• 2011

A robot education system by emulation based on Web can be efficiently used for understanding concept of robot assembly practice and control mechanism of robot by control programming. It is important to predict the path of the line tracer robot which has to be decided by the robot. Shortest Path Algorithm is a well known algorithm which searches the most efficient path between the start node and the end node. There are two related typical algorithms. Dijkstra Algorithm searches the shortest path tree from a node to the rest of the other nodes. $A^*$ Algorithm searches the shortest paths among all nodes. The delay time caused by turning the direction of navigation for the line tracer robot at the crossroads can give big differences to the travel time of the robot. So we need an efficient path determine algorithm which can solve this problem. Thus, It is necessary to analyze the overhead of changing direction of robot at multi-linked node to determine the next direction for efficient routings. In this paper, we reflect the real delay time of directional changing from the real robot. A speed based Dijkstra algorithm is proposed and compared with the previous ones to analyze the performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.12
• /
• pp.1182-1188
• /
• 2010

This paper proposes a precise localization algorithm for a quickly moving mobile robot. In order to localize a mobile robot with active beacon sensors, a relatively long time is needed, since the distance to the beacon is measured using the flight time of the ultrasonic signal. The measurement time does not cause a high error rate when the mobile robot moves slowly. However, with an increase of the mobile robot's speed, the localization error becomes too high to use for accurate mobile robot navigation. Therefore, in this research into high speed mobile robot operations, instead of using two active beacons for localization an active beacon and dual compass are utilized to localize the mobile robot. This new approach resolves the high localization error caused by the speed of the mobile robot. The performance of the precise localization algorithm was verified by comparing it to the conventional method through real-world experiments.

• Journal of Navigation and Port Research
• /
• v.46 no.6
• /
• pp.554-561
• /
• 2022

Technology development related to maritime autonomous surface ships (MASS) is actively progressing around the world. However, since there are still many technically unresolved problems such as communication, cybersecurity, and emergency response capabilities, it is expected that it will take a lot of time for MASS to be commercialized. In this study, we proposed a ship group navigation system in which one leader ship and several follower ship are grouped into one group. In this system, when the leader ship begins to navigate, the follower ship autonomously follows the path of the leader ship. For path following, PD (proportional-derivative) control is applied. In addition, each ship navigates in a straight line shape while maintaining a safe distance to prevent collisions. Speed control was implemented to maintain a safe distance between ships. Simulations were performed to verify the ship group navigation system. The ship used in the simulation is the L-7 model of KVLCC2, which has related data disclosed. And the MMG (Maneuvering Modeling Group) standard method proposed by the Japan Society of Naval Architects and Ocean Engineering (JASNAOE) was used as a model of ship maneuvering motion. As a result of the simulation, the leader ship navigated along a predetermined route, and the follower ship navigated along the leader ship's path. During the simulation, it was found that the three ships maintained a straight line shape and a safe distance between them. The ship group navigation system is expected to be used as a navigation system to solve the problems of MASS.

• Journal of Advanced Navigation Technology
• /
• v.5 no.1
• /
• pp.85-96
• /
• 2001

Recent development of a smart structures module and its successful integration with a multidisciplinary design optimization software $ASTROS^*$ and an Aeroservoelasticity module is presented. A modeled F-16 wing using piezoelectric actuators is used as an example to demonstrate the integrated software capability to design a flutter suppression system. For an active control design, neural network based controller is used for this study. A smart structures module is developed by modifying the existing thermal loads module in $ASTROS^*$ in order to include the effects of the induced strain due to piezoelectric actuation. The control surface/piezoelectric equivalence model principle is developed, which ensures the interchangeability between the control surface force input and the piezoelectric force input to the Aeroservoelasticity modules in $ASTROS^*$. The results show that the developed controller can increase the flutter speed.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.04a
• /
• pp.56-63
• /
• 2000

Abstract - In this paper, an adaptive mechanism based on immune algorithm is designed and it is applied for the autonomous guided vehicle(AGV) driving. When the immune algorithm is applied to the PID controller, there exists the case that the plant is damaged due to the abrupt change of PID parameters since the parameters are adjusted almost randomly. To solve this problem, a neural network is used to model the plant and the parameter tuning of the model is performed by the immune algorithm. After the PID parameters are determined in this off-line manner, these gains are then applied to the plant for the on-line control using immune adaptive algorithm. Moreover, even though the neural network model may not be accurate enough intially, the weighting parameters are adjusted to be accurate through the on-line fine tuning. The computer simulation for the control of steering and speed of AGV is performed. The results show that the proposed controller has better performances than other conventional controllers.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.432-434
• /
• 1998

Recently, For the material transport is increased, the AGV(Automated Guided Vehicle) is the most important part in the industrial factory. So we treat the navigation control problem and experimental results using microprocessor. In navigation control, we have faced with velocity control problem related to guide path tracking problem. Carefully, In the straight line, the AGV moves at its high speed, but in the curve line, especially when the radian ratio is very big it is difficult to follow guide line. So, Using fuzzy controller we have simulated the guide path following AGV according to the varying velocity and experimented it with microprocessor.(Intel 80C196KC) Now, If we use the AGV industrial factory, we will improve the product and efficiency in spite of changing the factory environment.

• Journal of the Korean Institute of Navigation
• /
• v.5 no.2
• /
• pp.1-39
• /
• 1981

A doppler log is the typical device which can measure the ship's speed over the ground directly, by means of doppler effect of the underwater ultrasonic wave, which involves the error due to the sea bottom inclination, the trim and the incorrect transducer installation etc. The present doppler log adopts a single transducer, faced in the direction of themain beam, and therefore it is unable to correct the beam direction to eliminate the above mentioned error. Moreover, the frequencyis also limitted in a comparatively high range for getting a sharp beam with single transducer, and the speed over the ground can not be detectable at the deep sea, for an instance, over 200 meters. This paper describes a theoretical consideration for the doppler log error and an analysis by a computer on the observed speed data by a full size model ship. The result is verified that the most of doppler log error is caused by the ultrasonic beam angle of transducer. To eliminate the doppler log error due to the incorrect transducer installation and also to sharpen the beam for lower frequency range to expand measurable sea depth, this paper proposes a method of controlling the directivity adopting a linear transducer array and of controlling the directivity by the control of exciting current, and investigates by the computer simulation and make experiment with magnetostrictive ferrite transducer of 28, 50 and 75KHz. The experimental results are shown well coincide with the measured ones, and they are revealed that in case where the transducer interval is greater than 1 wavelength, the effective control of the beam direction is hardly performed with keeping adequate beam width and side lobe level. It is concluded that 6-elements array with inter element space of a half wavelength can make comparatively sharp beam and low side lobe level. The results obtained here will contribute very much to the improvement of the performance of doppler log.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.3
• /
• pp.724-732
• /
• 2013

The purpose of this study is to obtain a basic data on layout of the trawlers' bridge equipment. The task activities of bridge workers involved in the navigation and fishing operation were analyzed by link analysis methods. The results are as follows. It was found that the movement pattern and frequency of bridge workers are different accordance with the bridge work (navigation, casting net, towing net and hauling net). The central workstation of movement of the bridge workers was a radar workstation, a steering workstation and a trawl winch workstation in the bridge work. But the radar did not show up as the center of movement during the hauling net. Workstations related deeply to the central workstations of the movement on the bridge were as below. Radar workstation was related to a GPS plotter, a microphone location for external communication with VHF and MF/HF equipment and a steering in the case of the navigation, the steering, the GPS plotter and the net monitor in the case of the fishing operation. Steering workstation was related deeply to the GPS plotter, the radar in the case of the navigation, a speed controller, the GPS plotter, a fish finder, the net monitor and the microphone location in the case of the fishing operation. Trawl winch workstation showed deep relation with the GPS plotter and the speed control during the fishing operation. Through this study, it was found that Workstations related deeply to the central workstation of the movement of the bridge workers in accordance with the bridge work. The results of this study might be utilized as the basic data on the bridge layout to minimize the fatigue degree due to a physical movement of the bridge workers.

• Journal of Advanced Navigation Technology
• /
• v.9 no.1
• /
• pp.71-78
• /
• 2005

Nowadays, the demand of HPI(High-speed Portable Internet) has been gradually increased to support the various services of high speed wire line internet such as xDS. HPI can support high speed internet in anyplace, anytime. For successful development of HPI, the performance should be evaluated according to the cell size and/or the number of users and cell design should be carried out based on these criteria. The previous cellular systems using CDMA technique focus on the establishment of link based on power control but HPI systems consider the QoS (Quality of Service) and its performance based on the scheduling technique. The results from the system level simulation show that the throughput is sensitive to the cell size and the number of users has little impact on it. Moreover, the variation of service delay is more sensitive to the number of users but less to the cell size.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1999.10a
• /
• pp.333-344
• /
• 1999

Currently many studies on the unmanned gantry crane for the automated container terminal are accomplished. This is needed for the development of large scale, automation, high speed, unmanned system and information system in port facility. In order to do efficient container handling job in port yard, the automated handling system is well adapted to the job environments and all-season weather, In order to realize the automatic and unmanned system for container handling job, the required functions and main structure system are studied. The major problems of operation of the conventional gantry crane are that the vibration of gantry structure body is occurred by operation and that high-speed and precision position-velocity control and the capability to dope to the external disturbances caused by the wind, rain, fog and job environments. In this paper, the fundamental study for establishment of the concept and the dynamic modelling of the major sub system of the unmanned gantry crane is presented. These studies are useful for design and manufacturing of the new concept model of the unmanned gantry crane for efficient operation of the automated container terminal.