• Journal of Electrochemical Science and Technology
• /
• 제9권1호
• /
• pp.28-36
• /
• 2018

Metal-organic frameworks have recently been considered very promising modifiers in electrochemical analysis due to their unique characteristics among which tunable pore sizes, crystalline ordered structures, large surface areas and chemical tenability are worth noting. In the present research, $Cu(btec)_{0.5}DMF$ was electrodeposited on the surface of glassy carbon electrode at room temperature under cathodic potential and was initially used as the active materials for the detection of $H_2O_2$. The cyclic voltammogram of $Cu(btec)_{0.5}DMF$ modified GC electrode shows distinct redox peaks potentials at +0.002 and +0.212 V in 0.1 M phosphate buffer solution (pH 6.5) corresponding to $Cu^{(II)}/Cu^{(I)}$ in $Cu(btec)_{0.5}DMF$. Acting as the electrode materials of a non-enzymatic $H_2O_2$ biosensor, the $Cu(btec)_{0.5}DMF$ brings about a promising electrocatalytic performance. The high electrocatalytic activity of the $Cu(btec)_{0.5}DMF$ modified GC electrode is demonstrated by the amperometric response towards $H_2O_2$ reduction with a wide linear range from $5{\mu}M$ to $8000{\mu}M$, a low detection limit of $0.865{\mu}M$, good stability and high selectivity at an applied potential of -0.2 V, which was higher than some $H_2O_2$ biosensors.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.361-361
• /
• 2010

The separated quasi-one-dimensional ($7{\times}7$) and ($5{\times}5$) phases on vicinal Si(557) surfaces were successfully realized by changing the crystallographic orientation and thermal treatment conditions. A small change in the crystallographic orientation of the Si(557) surface stabilized the quasi-one-dimensional ($5{\times}5$) phase of a (111) facet on vicinal Si(557) surfaces and made it coexist with a quasi-one-dimensional ($7{\times}7$) phase after an optimal thermal treatment, whereas only the quasi-one-dimensional ($7{\times}7$) phase was stable on the Si(557) surface. Interestingly, this causes the (111) terraces with different widths (L) to prefer only one of the $5{\times}5$ (L=12) and $7{\times}7$ (L=9) phases resulting in long-range order of both phases along the step edge direction, which was observed by scanning tunneling microscopy (STM) and was supported by first principle calculations. In contrast, the quasi-one-dimensional ($5{\times}5$ and ($7{\times}7$) phases were arranged randomly across the step edge direction. The change of surface morphology of vicinal Si(557) surfaces will be discussed with STM images and theoretical calculations by changing crystallographic cutting angles and thermal treatment conditions.

• 한국진공학회지
• /
• 제19권6호
• /
• pp.397-407
• /
• 2010

나노재료기술이 지속적으로 발전하기 위해서는 기술 개발 못지않게 개발된 기술이 사회에 순조롭게 용납될 수 있는 윤리적 시스템이 개발되어야 한다. 이 논문에서는 나노기술의 윤리적 문제들에 대한 국내외 연구동향을 종합하고, 특히 나노재료의 환경 건강 안전성 관련 윤리적 문제들과 이를 해결하기 위한 실용적인 도구로서 전 세계적으로 개발되고 있는 이해 당사자 간의 소통 규제 인증, 안전지침을 비판적으로 개괄하여 보았으며, 마지막으로 나노재료의 안전한 사용을 위한 윤리적 시스템 구축에 관한 정책 제안을 하였다.

• 한국진공학회지
• /
• 제22권4호
• /
• pp.204-210
• /
• 2013

임플란트와의 골융합을 향상시키기 위해서 세포와 임플란트 표면의 나노구조의 상호작용에 대한 이해가 중요하다. 본 연구에서는 Sn를 촉매로 이용하여 Vapor-Liquid-Solid 법을 이용하여 $TiO_2$ 나노와이어를 튜브 전기로 안에서 질소기체 조건하에서 합성하였다. 이 때 촉매로 사용된 Sn 박막의 두께에 따라 응집된 나노스피어를 이용하여 $TiO_2$ 나노와이어의 크기를 조절하였다. 골융합을 위한 예비 실험으로써, 만들어진 $TiO_2$ 나노와이어 샘플 위에서 조골전구세포(pre-osteoblast)를 1주일간 배양하였고, 세포가 $TiO_2$ 나노와이어에 잘 결합함을 볼 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.275-275
• /
• 2013

Osteoblast is one of cells related with osseointegration and many research have conducted the adhesion of osteoblast onto the surface of implant. In the osseointegration, biocompatibility of the implant and cell adhesion to the surface are important factors. The researches related to cell adhesion have a direction from micro-scaled surface roughness to nano-scaled surface roughness with advancing nanotechnology. A cell reacts and sense to stimuli from extracellular matrix (ECM) and topography of the ECM [1]. Thus, for better osseointegration, we should provide an environment similar to ECM. In this study, we synthesize TiO2 nanowires using hydrothermal reaction because TiO2 provides inertness to titanium on its surface and enables it used as an implant material for the orthopedic treatment such as fixation of the bone fracture [2]. Ti substrate is immersed into NaOH aqueous solution. The solution are heated at $140{\sim}200^{\circ}C$ for various time (10~720 minutes). After heat treatment, we take out the sample and immerse it into HCl aqueous solution for 1 hour. The acid treated sample is heated again at $500^{\circ}C$ for 3 hours [3]. Then, we culture osteoblast on the TiO2 nanowires. For investigating cell adhesion onto nanostructured surface, we conduct several tests such as MTT assay, ALP (Alkaline phosphatase) activity assay, measuring calcium expression, and so on. These preliminary results of the cell culture on the nanowires are foundation for investigating cell-material interaction especially with nanostructure interaction.

• 대한금속재료학회지
• /
• 제48권11호
• /
• pp.974-980
• /
• 2010

Various types of steel, namely, 0.35C, 0.2C-Cr, and 0.2C-Cr-Mo steels, were quenched and tempered by high-frequency induction heat treatment. The type, size, and spheroidization of the carbides varied depending on the tempering temperatures ($450{\sim}720^{\circ}C$). During the tempering process, the carbide was precipitated in the martensite matrix. The 0.35C, 0.2C-Cr, and 0.2C-Cr-Mo steels contained carbides that were smaller than 120 nm. The carbide was spheroidized as the tempering temperature increased. Owing to the fine microstructure and spheroidization of the carbides, all three steels had a high tensile strength as well as yield ratio and reduction of area. In the case of the 0.2C-Cr steel, the use of Cr as an alloying element facilitated the precipitation of alloyed carbides with an extremely small particle and resulted in an increase in the spheroidization rate of the carbides. As a result, a large reduction of area was achieved (>70%). The 0.2C-Cr-Mo steel had the highest tensile strength because of the high hardenability that can be attributed to the presence of alloying elements (Cr and Mo). Quenching and tempering steels by induction heat treatment resulted in a high strength of over 1 GPa and a large reduction of area (>70%) because of the rapid heating and cooling rates.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.630-638
• /
• 2010

The present investigation has been performed on the mixing behavior and microstructural development during fabrication of Fe micro-nano powder feedstock for a micro-powder injection molding process. The mixing experiment using a screw type blender system was conducted to measure the variations of torque and temperature during mixing of Fe powder-binder feedstock with progressive powder loading for various nano-powder compositions up to 25%. It was found that the torque and the temperature required in the mixing of feedstock increased proportionally with increasing cumulative powder loading. Such an increment was larger in the feedstock containing higher content of nano-powder at the same powder loading condition. However, the maximum value was obtained at the nano-powder composition of not 25% but 10%. It was owing to the 'roller bearing effect' of agglomerate type nano-powder acting as lubricant during mixing, consequently leading to the rearrangement of micro-nano powder in the feedstock. It is concluded that the improvement of packing density by rearrangement of nano-powders into interstices of micro-powders is responsible for the maximum powder loading of about 71 vol.% in the nano-powder composition of 25%.

• 대한금속재료학회지
• /
• 제48권12호
• /
• pp.1130-1135
• /
• 2010

Cu/carbon nano-particle hybrids were fabricated through the cathodic electrophoretic deposition (EPD) process. CNT and CNF nano-particles were modified to give positive charges by polyethyleneimine (PEI) treatment before depositing them on the substrate. Since a Cu plate was used as an anode in the EPD process, Cu particles were also deposited along with the carbon nano-particles. Experimental observation showed the nano-hybrids constructed a novel formicary-like nano-structure which is strong and highly conductive. Utilizing the hybrids, carbon fiber composites were manufactured, and their electrical conductivity and interlaminar shear strength were measured. In addition, the deposition morphology and failure surface were examined by SEM observations. Results demonstrated that the electrical conductivities in the through-the-thickness direction and the interlaminar shear strength significantly increased by 350~2100% and 14%, respectively.

• 대한금속재료학회지
• /
• 제48권9호
• /
• pp.807-812
• /
• 2010

In this paper, the Ultrasonic Nanocrystalline Surface Modification (UNSM) surface treatment process was used to induce compressive residual stress and nanocrystalline structure by severe plastic deformation on the UNSM-treated surface. The test results for AISI304 stainless steel demonstrated that the grain size was found to be 23 nm, the dislocation density was increased by $0.2085{\times}10^{18}\;m^{-2}$, and the volume fraction of martensite is defined as 27.6% from austenite so that the surface hardness of the surface is increased from 200 Hv up to 515 Hv. The initial tensile residual stress is changed from 300 MPa to a compressive residual stress of 500 MPa after UNSM treatment. In addition, UNSM was applied under five various conditions, and the results of those conditions were defined as a function of depth quantitative.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.206-211
• /
• 2012

Graphene has recently received high attention as a promising material for various applications, and many related studies have been undertaken to reveal its basic mechanical properties. However, the tribological properties of graphene film fabricated by the chemical vapor deposition (CVD) method are barely known. In this study, the contact angle and frictional wear characteristics of graphene coated copper film were investigated under room temperature, normal air pressure, and no lubrication condition. The contact angle was measured by sessile drop method and the wear test was carried out under normal loads of 660 mN and 2940 mN, respectively. The tribological behaviors of a graphene coating layer were also examined. Compared to heat treated bare copper foil, the graphene coated one shows a higher contact angle and lower friction coefficient.