• Korean Chemical Engineering Research
• /
• 제53권3호
• /
• pp.372-381
• /
• 2015

본 연구에서는 $Ni/Al_2O_3$ 촉매를 사용한 에틸렌글리콜의 수증기 개질반응에서 제조 방법에 따른 영향을 알아보았다. 촉매들은 건식 함침법, 습식 함침법 그리고 공침법을 사용하여 제조하였다. 공침법을 사용하여 촉매 제조시 침전제를 KOH, $K_2CO_3$, $NH_4OH$를 각각 사용하여 침전제에 따른 영향 또한 알아보았다. 제조한 촉매들은 질소 물리흡착, 유도결합 플라즈마 질량분석법(ICP-AES), X선 회절법(XRD), 수소 승온 환원법(TPR), 수소 화학흡착, 승온 산화법(TPO), 주사전자현미경(SEM), 열분석법(TGA)을 사용하여 촉매의 물리화학적인 특성을 분석하였다. 773 K에서 환원한 촉매의 경우 KOH 혹은 $K_2CO_3$를 침전제로 사용하여 공침법으로 제조한 촉매가 가장 높은 활성을 보였다. 촉매 제조 방법은 Ni의 입자크기, Ni 산화물의 환원도, 반응에서의 활성과 안정성, 반응 중 탄소 침적의 형태 등에 영향을 끼치는 것을 확인할 수 있었다. KOH를 침전제로 사용하여 공침법으로 제조한 촉매의 경우 환원온도를 773~1173 K까지 증가시켰을 때, Ni 입자크기의 증가에도 불구하고 Ni 산화물의 환원도가 증가하므로 반응활성이 증가하는 것으로 나타났다.

• Applied Microscopy
• /
• 제26권3호
• /
• pp.379-388
• /
• 1996

Structure of premartensite in $Ti_{50}Ni_{49}Fe_1\;and\;Ti_{50}Ni_{50}$ prepared by self-propagating high temperature synthesis (SHS) method has been investigated by a detailed transmission electron microscopy. $Ti_{50}Ni_{49}Fe_1$ consists of microdomain area and needle type domain area. On the other hand, $Ti_{50}Ni_{50}$ consists of microdomain-free and microdomain area, and needle type domain area. Various types of extra superreflections, such as 1/2<100>, 1/2<110> and 1/4<210> type superreflection have been observed in the selected area electron diffractions from microdomain area. Such extra superreflections are due to transformation from B2 structure to distorted B2 structure or premartensite. The present study shows that incommensurate phase forms as an intermediate phase during martensitic transformation. Particularly, in Fe-free $Ti_{50}Ni_{50}$, two types of matrix phases have been observed, microdomain and microdomain-free area. Types of extra superreflections in $Ti_{50}Ni_{50}$ are different from those in $Ti_{50}Ni_{49}Fe_1$, i.e. 1/7<321> type superreflections have been observed, instead of 1/2<110>, 1/2<100>, 1/4<210> types in $Ti_{50}Ni_{49}Fe_1$.

• 한국재료학회지
• /
• 제15권12호
• /
• pp.765-772
• /
• 2005

PAS(Plasma Activated Sintering) process was tried to apply for the fabrication of BMG(Bulk Metallic Glasses) of $Ni_{57}Zr_{20}Ti_{18}Si_5}\;and\;Ni_{57}Zr_{20}Ti_{18}Si_3Sn_2$ from the as-atomized amorphous powder. Compressive strength for the BMG(bulk Metallic Glasses) of $Ni_{57}Zr_{20}Ti_{18}Si_5$ were lower than those of BMG rods produced by warm extrusion ,or copper mold casting method. Microstructural examination by optical microcope, SEM ana EDS showed that oxidation had occurred during PASintering. In order to prevent the powder from the oxidation during PASintering, Ni coating for $Ni_{57}Zr_{20}Ti_{18}Si_5$ amorphous powder by electroless-plating method was performed. Microstructural examination for Ni coated layers after PASintering indicated that the Ni coating had been so effective to prevent powder from oxidation during PASintering. Sintering behaviors of $Ni_{57}Zr_{20}Ti_{18}Si_3Sn_2$ represent the same as those of $Ni_{57}Zr_{20}Ti_{18}Si_5$.

• 한국재료학회지
• /
• 제30권12호
• /
• pp.672-677
• /
• 2020

Expensive PCBN or ceramic cutting tools are used for the processing of difficult-to-cut materials such as Ti and Ni alloy materials. These tools have a problem of breaking easily due to their high hardness but low fracture toughness. To solve this problem, cutting tools that form various coating layers are used in low-cost WC-Co hard material tools, and researches on various tool materials are being conducted. In this study, WC-5, 10, and 15 wt%Ni hard materials for difficult-to-cut cutting materials are densified using horizontal ball milled WC-Ni powders and pulsed current activated sintering method (PCAS method). Each PCASed WC-Ni hard materials are almost completely dense, with a relative density of up to 99.7 ~ 99.9 %, after the simultaneous application of pressure of 60 MPa and electric current for 2 min; process involves almost no change in the grain size. The average grain sizes of WC and Ni for WC-5, 10, and 15 wt%Ni hard materials are about 1.09 ~ 1.29 and 0.31 ~ 0.51 µm, respectively. Vickers hardness and fracture toughness of WC-5, 10, and 15 wt%Ni hard materials are about 1,923 ~ 1,788 kg/mm2 and 13.2 ~ 14.3 MPa.m1/2, respectively. Microstructure and phase analyses of PCASed WC-Ni hard materials are performed.

• 대한치과기공학회지
• /
• 제23권1호
• /
• pp.9-19
• /
• 2001

Microstructure and phase transformation of Ti-Ni-Cu alloy powders produced by using attrition milling method were studied. Mixed powders of Ti-(50-X)Ni-XCu ($X=0{\sim}20$ at%) in composition range were mechanically alloyed for maximum 20 hours by using SUS 1/4" ball in argon atmosphere. Ball to powder ratio was 50: 1 and impeller speed was 350rpm. Mechanically alloyed with attrition millimg method. powder was heat treated at the temperature up to $850^{\circ}C$ for 1 hour in the $10^{-6}$ torr vacuum. Ti-Ni-Cu alloy powders have been fabricated by attrition milling method. and then phase transformation behaviours and microstructual properties of the alloy powders were investigated to assist in improving the the high damping capacity of Ti-Ni-Cu shape memory alloy powders. The results obtained are as follows: 1. After heat treating of fully mechanically alloyed powder at $850^{\circ}C$ for 1hour. most of the B2 and B 19' phases was formed and $TiNi_3$ were coexisted. 2. The B 19' martensite were formed in Ti-Ni-Cu alloy powders whose Cu-content is less than 5a/o. where as the B19 martensite in those whose Cu-content is more than 10at%. 3. The powders of as-milled Ti-Ni-Cu alloys whose Cu-contents is less than 5at% are amorphous. whereas those of as-milled Ti-Ni-Cu alloys whose Cu-content is more than 10at% are crystalline. This means that Cu addition tends to suppress amorphization of Ti-Ni alloy powders.

• 한국산학기술학회논문지
• /
• 제16권5호
• /
• pp.2993-2999
• /
• 2015

강 제조 회사들은 연속주조금형의 표면을 보호하기 위해 Ni-B 또는 Ni-Co 합금 도금을 적용하고 있으며, 도금 층에 균열이 생기게 하는 황을 함유한 사카린 윤활제를 사용하고 있다. 균열 및 인장 응력을 유발하는 것은 Ni-S 화합물로 여겨진다. Ni-Mn-B 삼원합금은 Ni-S 화합물이 형성되기 이전에 Mn-S 화합물을 형성하여 균열을 억제하기 위해서 개발되었으나, Ni-Mn-B 합금 도금에 관한 국내나 해외 기준이 없다. 그리하여 새로이 개발된 Ni-Mn-B 도금을 평가하기 위한 신뢰성 평가기준을 개정하려한다. 가속수명시험을 개발하기 위해 FMEA(고장형태 영향분석)가 사용되어 도금의 주요 파괴 원인을 분석하였다. Ni-Mn-B 신뢰성 기준은 가속수명시험 방법을 포함하였고, 기본 성능 시험과 환경시험, 가속수명시험으로 분류되었으며, 80% 신뢰수준으로 B10수명 1 000시간을 보장하도록 고안되었다.

• Tribology and Lubricants
• /
• 제26권1호
• /
• pp.68-72
• /
• 2010

A ceramic coating is a surface treatment method that is being used widely in the industrial field, recently. Ni-P plating is also being used widely because of its corrosion resistance and low cost. An anodizing method is applicable to aluminum alloy. An anodizing method generates a thick oxide layer on the surface and then, that heightens hardness and protects the surface. These surface treatments are applied to various mechanical components and treated surfaces relatively move one another. In this study, tribological characteristics of Ni-P plating and TiAlN coating on anodized Al alloy are compared. The counterpart, anodized Al alloy, is worn out abrasively by Ni-P plating and TiAlN coating that have higher hardness. Abrasively worn debris accumulated on the surfaces of Ni-P plating and TiAlN coating, and then transferred layer is formed. This transferred layer affects the amplitude of variation of friction coefficient, which is related to noise and vibration. The amplitude of variation of friction coefficient of Ni-P plating is lower than those of TiAlN coating during the tests.

• 분석과학
• /
• 제13권2호
• /
• pp.194-199
• /
• 2000

본 연구에서는 Ni가 처리된 PAN계 ACFs에 대하여 흡착, 표면특성 및 항균효과를 통하여 물리 화학적인 특성과 생물학적인 특성을 제시하였다. Ni가 처리된 PAN계 ACFs의 흡착에 관한 연구로부터 N1-N3에 대하여 Type I의 흡착등온곡선과 N4-N6에 대하여 Type II와 III의 흡착등온곡선을 각각 얻었다. 이들 시료에 대하여 흡착된 부피는 Ni의 몰농도의 증가와 함께 천천히 감소함을 알 수 있었다. BET식을 사용하여 계산된 $S_{BET}$값은 $692.58-895.24m^2/g$의 범위에 분포하였다. 또한 common-t값을 사용하여 ${\alpha}_s$-법으로부터 구한 단위 질량 당 미세 동공 부피는 $0.19-0.56cm^3/g$이었다. SEM 모폴로지의 결과로부터 PAN계 ACFs의 표면은 Ni를 처리함에 따라 부분적으로 피복됨을 관찰 할 수 있었다. 최종적으로 Shake flask법을 사용한 대장균(E. coli)에 대한 항균 효과를 측정한 결과, 각각의 시료들은 92.5-100%의 효과를 나타내었다. 이러한 항균 효과는 역시 Ni의 몰농도의 증가와 함께 향상됨을 알 수 있었다.

• 한국표면공학회지
• /
• 제51권4호
• /
• pp.197-201
• /
• 2018

Dynamic nano-indentation method was applied to characterize thin electroformed Ni-P layers. The Ni-P layers were produced in a sulphamic acid bath at $50^{\circ}C$ in $0.02A/cm^2$ for 10-60 minutes. The chemical analyses by XRD and EDX showed that the Ni-P layers were very fine grains with mainly $Ni_3P$ with Ni. The surface roughness determined by atomic force microscopy increased with thickness, which was relative to the surface morphology. The nano-hardness and the stiffness of the thin Ni-P layers with thickness of 1.9, 6.2 and $7.5{\mu}m$ were 5.52, 6.52 and 6.77 [GPa] and 56.7, 76.2 and 108.0 [${\mu}N/nm$], respectively. The elastic modulus of the Ni-P layer increased with thickness such as 37.29, 54.50 and 78.76 [GPa], respectively. The surface roughness of the electroplated Ni-P layers with diverse thickness was 8.66, 18.56 and 35.22 [nm], respectively. The enhanced nano-mechanical properties were related to mainly residual stress of the Ni-P layers.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.119-122
• /
• 2002

The NiO buffer layers for YBCO coated conductor were prepared on textured Ni substrates by MOCVD method and the degree of texturizing and the surface roughness were analyzed X-ray pole figure and AFM and SEM. Processing variables were oxygen partial pressure and substrate temperature. (200) textured NiO layer was formed at 450~$470^{\circ}C$ and oxygen partial pressure of 1.67 Torr. Out-of-plane($\omega$-scan) and in-plane($\Phi$-scan) texture were $10.34^{\circ}$ and $10.00^{\circ}$ respectively. The surface roughness estimated by atomic force microscopy was in the range of 3.1~4.6 nm.