• Particle and aerosol research
• /
• v.15 no.4
• /
• pp.139-148
• /
• 2019

This study was performed for the application of a high-speed centrifugal cyclone to shale gas mining process. This device uses the centrifugal force to control particles similar to typical cyclones, and the disk located inside the cyclone is forced to rotate using a motor. The pressure difference occurred during the rotating of disk. Hence, inflow rate was generated without a blower fan. In addition, flow rate increased with elevating rpm of motor. The installing the disk in multiple stages on the inner rotor increased the instantaneous disk outlet flow. Hence, the control efficiency of oil particle increased from 1.05% to 31.2%. By modifying the structure of the disk so that the air flow to the opposite direction of the cyclone, the control efficiency of oil particles increased to 81.5%. By increasing the capacity of the motor and the size of the disk, the flow rate was increased to 2.5 ㎥/min because the rpm of motor and pressure difference increased. As rpm of motor increased, the cut-off diameter (d_pc) became smaller. Unlike the Lapple's equation, d_pc was inversely proportional to the effective number of rotations (N_e). The control efficiency was maintained even if the concentration of oil particles increased, for this reason, the higher the oil concentration, the more particles were accumulated and controlled.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.3
• /
• pp.267-272
• /
• 2011

We analyzed the wear characterization of $Si_3N_4$ ceramics according to the amount of added $SiO_2$ nanocolloid. The test specimen was prepared by hot-press sintering at 35 MPa and 2123 K in an $N_2$ gas atmosphere for 1 h. A wear test was performed with a block-on-ring tester, and the test conditions were as follows: (1) the ring with a diameter of 35 mm had a rotational speed of 50 rpm; (2) the load was 9.8 N; and (3) the temperature was $25^{\circ}C$. The test results show that $Si_3N_4$ ceramics have a friction coefficient of about 1.0 and a wear loss of about 0.02 mm. Of the specimens used this study, the test specimen with 1.3 wt% of added $SiO_2$ nanocolloid has the best wear resistance because it has the lowest friction coefficient and the smallest wear loss. This specimen also has the highest Vickers hardness and bending strength. In this study, the friction coefficient is inversely proportional to the hardness and bending strength.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.4
• /
• pp.100-106
• /
• 1993

A study on optimizing the friction welding of copper(C1100) to aluminium(A1050) for developing the electrical sleeve was experimentally carried out and also on real-time nondestructive evaluation of the friction weld quality (strength) was accomplished by acoustic emission technique. The results obtained are summarized as the following ; 1) The heating upset $U_1$(mm) or total upset U(mm) tends to increase according to the increase of heating time $t_1$(sec). The relations between $U_1$ and $t_1$ or U and $t_1$are computed as follows when n=2000rpm, $P_1$=4, $P_2$=8kgf/$mm^2$, and $t_2$=6sec. U=1.6$e^{0.39t_1}$ $U_1$=3.65$e^{0.25t_1}$. 2) It was notified that the proper welding conditions by considering on both strength with more than 100% joint effieciency and toughness are heating time of 1.5-2.25 sec under n=200rpm, $P_1$=4, $P_2$=8kgf/$mm^2$, $t_2$=6sec. 3) It was confirmed that both AE total counts(N, counts) and the weld tensile strength (${\sigma}$, kgf/$mm^2$) of the welded joints increase as the increase of heating time, respectively, the relations between N and $t_1$, ${\sigma}$ and $t_1$ are computed from data points by regression analysis using the least square method as follows in case of the above proper condition ; N=50108+23917(ln $t_1$)${\sigma}$$=11.85+2.06(ln $t_1$). 4) Both empirical and calcularated equations of relationship between .sigma. and N are very coincident with a high reliability, as the following in case of the above proper welding condition ; Calculated : ${\sigma}$=0.00008N+7.5 Empirical :${\sigma}$= $8.17e^{0.0000072N}$. 5) It was confirmed that the real-time nondestructive weld strength evaluation for friction welding of copper(C1100) to aluminium(A1050) could be possible by acoustic emission technique.

• Advances in materials Research
• /
• v.3 no.3
• /
• pp.175-183
• /
• 2014

Natural rubber bound phenolic antioxidant, 2,6-di-tert-butyl-4-vinylphenol (2,6-DBVP), was prepared from natural rubber and 2,6-DBVP in both solution and melt state. The 2,6-DBVP had been synthesized from 3,5-di-tert-butyl-4-hydroxybenzaldehyde and methyltriphenylphosphonium iodide ($MePPh_3I$) by Wittig reaction ($0^{\circ}C$ for 2 hrs, $N_2$ atmosphere). The conditions for preparation of natural rubber bound 2,6-DBVP (NR-DBVP) were optimized for both solution state (1 phr BPO and 8 phr 2,6-DBVP at $70^{\circ}C$ for 2 hrs) and for melt state (1 phr BPO and 8 phr 2,6-DBVP at $70^{\circ}C$ for 10 mins, with rotor speed of 60 rpm). A thermoplastic vulcanizate was obtained using a compatibilizer, polypropylene modified with phenolic resin (PhHRJ-PP), in a closed mixer ($180^{\circ}C$ for 3 mins, rotor speed 60 rpm). The antioxidant properties of vulcanized NR-DBVP, using phenolic as the vulcanization system, were similar to NR with the conventional antioxidant BHT. In addition, the antioxidant, water leaching property of the thermoplastic vulcanizate of NR-DBVP/PP were good in comparison to a NR blend with BHT; the morphologies of these thermoplastic vulcanizates were similar.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.66-72
• /
• 2000

Commercial eddy current dynamometers control the torque of ratating body (poer supply machine) with the field coil current being operated as a braking force. In this paper, we studied about the relation between the field coil current and the torque load of eddy current dynamometer. By the torque measuring analysis of eddy current dynamometer, it is linear relation between the brake force measured from the torque meter (e.g. load cell, strain gage or spring balance etc.) which is installed at the case of dynamometer and the multiply of shaft rpm by the square of field coil current (N$\times$Ia2). To prove the relation, it was experimented and showed that the torque operated by the rotating body can be measured with the shaft rpm and the field coil current of eddy current dynamometer. This result shows a possibility that eddy current dynamometer can measures the torque of rotating body without special torque measuring devices.

• Korean Journal of Food Science and Technology
• /
• v.32 no.2
• /
• pp.417-423
• /
• 2000

Lactobacillus plantarum KLAB21 isolated from Kimchi has been reported to produce antimutagenic subtance(s) in the culture medium. In this study, antimutagenic effects of the strain KLAB21 were investigated to under various culture conditions maximize the production of antimutagenic substance(s) against N-methyl-N'-nitro-N-nitrosoguanidine(MNNG) on Salmonella typhimurium TA100 and 4-nitroquinoline-1-oxide(NQO) on S. typhimurium TA98. Glucose(2%) as a carbon source and yeast extract(1%) as a nitrogen source resulted in the highest production of the antimutagenic substance(s) against both mutagens in the culture supernatant of L. plantarum KLAB21. The most effective concentrations of bactopeptone as a nitrogen source were 1% against MNNG and 1.5% against NQO. Optimal pH of the medium, culture temperature, and shaking speed for the antimutagenic substance(s) production were pH 7.0, $37^{\circ}C$ and 150 rpm, respectively. Under the optimal condition, the antimutagenic effects of L. plantarum KLAB21 culture supernatant were 98.4% against MNNG on S. typhimurium TA100 and 57.3% against NQO on S. typhimurium TA98.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.166-166
• /
• 2007

ZnO는 육방정계(wurtzite) 결정구조를 지니며 상온에서 3.37eV의 wide band gap을 갖는다. ZnO의 엑시톤 결합 에너지는 GaN에 비해 2.5배 높은 60meV로서 고효율의 광소자 적용 가능성이 높다. 또한 고품위의 박막합성이 가능하다. 이러한 특성 때문에 display소자의 투명전극, 광전소자, 바리스터, 압전소자, 가스센서 등에 폭 넓게 응용되고 있다. ZnO박막의 제조는 스퍼터링, CVD, 진공증착법, 열분해법 등이 있다. 본 논문에서는 RF 마그네트론 스퍼터에 의해 제작된 ZnO 박막에 CMP공정을 수행하여 연마율과 비균일도 특성 및 광투과 특성을 연구하였다. ZnO박막은 $2{\times}2Cm$의 Corning glass위에 증착되었다. 로터리 펌프와 유확산 펌프를 이용하여 초기진공을 $2{\times}10^{-6}$ Torr까지 도달시킨 후 Ar과 $O_2$를 주입하였다. 증착은 상온에서 이루어졌으며 공정압력은 $6{\times}10^{-2}$Torr이였다. 초기의 불안정한 상태의 풀라즈마를 안정시키기 위해 셔터를 이용하여 pre-sputtering을 하였다. CMP 공정조건은 플레이튼 속도, 슬러리 유속, 압력은 칵각 60rpm, 90ml/min, $300g/cm^2$으로 일정하게 유지하였으며 헤드속도는 20rpm에서 100rpm까지 증가시키면서 연마특성을 조사하였다. 실리카슬러리의 적합성을 알아보기 위해 DIW와 병행하여 CMP공정을 수행하고 비교 분석하였다. CMP공정 결과 광투과도는 굉탄화된 표면의 확보로 인해 향상된 특성을 보였다. 실리카 슬러리를 사용하여 CMP를 할 경우는 헤드속도는 저속으로 하여야 양호한 연마특성을 얻을 수 있었다.

• Journal of ILASS-Korea
• /
• v.27 no.3
• /
• pp.117-125
• /
• 2022

This study examines whether engine fuel efficiency is improved by optimization of the exhaust valve timing in a state where the intake valve timing has been optimized in a small turbo gasoline engine that has intake cams and exhaust cams with fixed valve opening periods. When the exhaust valve is opened late, the expansion stroke is longer, and the efficiency can be improved. A 2-cylinder turbo gasoline engine with 0.8 liters of displacement and an MPI (Multi Point Injection) fuel system was used. The engine was operated at 1,500 and 3,000 rpm, and the load conditions included a partial load of 50 N·m and a high load of 70 N·m. Data was recorded as the exhaust valve timing was controlled, and this was used to calculate the efficiency of combustion using a heat release, the fuel conversion efficiency, and the pumping loss. Results and the hydrocarbon concentrations in the exhaust gas were compared for each condition. Experiment results confirmed that additional fuel efficiency improvements are possible through exhaust valve timing control at 1,500 rpm and 50 N·m. However, in other operating conditions, fuel efficiency improvements could not be obtained through exhaust valve timing control because cases where the pumping loss and fuel/air mixture slip increased when the exhaust valve timing changed and the fuel efficiency declined.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.5
• /
• pp.36-43
• /
• 2008

This research is tendencious to manufacture solid piston-rod of shock absorber as hollow piston-rod using friction welding. The SM45C has been welded to the SM45C-pipe in order to investigate the effect of upset pressure on friction weldability. The friction time and upset pressure was variable conditions under the conditions of spindle revolution of 2,000rpm, friction pressure of 55MPa, and upset time of 2.0seconds. Under these conditions, the microstructure of weld interface, tensile fracture surface and mechanical tests were studied of friction weld, and so the results were as follows. When the upset pressure is sufficient, gets the high tensile strength. The optimal welding conditions were n=2,000rpm, $P_1$=55MPa, $P_2$=95MPa, $t_1$=1.5sec, $t_2$=2.0sec when the total upset length is 4.5mm.

• Journal of Life Science
• /
• v.11 no.5
• /
• pp.439-446
• /
• 2001

Leuconostoc mesenteroides subsp. cremoris DLAB19 were investgated under various culture conditions to maximize the production of antimutagenic substance(s) against N-methyl-N\`-nitro-N-nitrosoguandine(MNNG) on Salmonella enterica serovar typhimurium TA100 and 4-nitroquinoline-1-oxide(4-NQO) on S. enterica serovar typhimurium TA98. The MRS medium containing glucose (2%) as a carbon source and yeasty extract (1%) as a nitrogen source resulted in the highest production of the antimutagenic substance(s) against both mutagens in the culture supernatant of Leu. mesenteroides subsp. cremoris DLAB19. Optimal pH of the culture medium, culture temperature and shaking speed for the antimutagenic substance(s) production were pH 7.0, 3$0^{\circ}C$ and 150 rpm, respectively. Under the optimal condition, the antimutagenic effects of Leu. mesenteroides subsp. cremoris DLAB19 culture supernatant were 96.4% against MNNG on S.enterica serovar typhimurium TA100 and 53.8% against 4-NQO on S. enterica serovar typhimurium TA98.