• Journal of the Korean earth science society
• /
• v.30 no.5
• /
• pp.550-564
• /
• 2009

When magnetotelluric (MT) data are obtained in the vicinity of the coast, the surrounding seas make it difficult to interpret subsurface structure, especially the deep part of the subsurface. We introduce an iterative method to correct the sea effect, based on the previous topographic correction method that removes the distortion due to topographic changes in seafloor MT data. The method first corrects the sea effect in observed MT impedance, and then inverts corrected response in a model space without the sea. Due to mutual coupling between the sea and the subsurface structure, the correction and inversion steps are iterated until the changes in each result become negligible. The method is tested for 1- and 2-D structures using synthetic MT data produced by 3-D forward modeling including surrounding seas. In all cases, the method closely recovers the true structure assumed to generate synthetic responses after a few iterations.

• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.668-678
• /
• 2003

For the purpose to facilitate development of high-speed spindle units (SUs) running on rolling bearings, we have developed a beam element model, algorithms, and software for computer analysis of thermal characteristics of SUs. The thermal model incorporates a model of heat generation in rolling bearings, a model of heat transfer from bearings, and models for estimation of temperature and temperature deformations of SU elements. We have carried out experimental test and made quantitative evaluation of the effect of operation conditions on friction and thermal characteristics of the SUs of grinding and turning machines of typical structures. It is found out that the operation conditions make stronger effect on SU temperatures when rpm increases. A comparison between the results of analysis and experiment proves their good mutual correspondence and allows us to recommend application of the models and software developed for design and research of high-speed SUs running on rolling bearings.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.452-459
• /
• 1997

For computer aided design and construction of low noisy power plants, indoor and outdoor noise prediction program has been developed. The program utilizes the predefined data of noise sources and building materials and has the faculty to estimate the source level using the empirical formula in case of the measured data not being available. In the noise prediction, the mutual noise propagation between indoor and outdoor sites are considered. The outdoor noise source in the calculation of geometric divergence effects is modelled as the omni-directional finite line or planar source according to the source geometry and the receiving points. Outdoor noise prediction is carried out to consider the diffraction effect due to plant structures as well as the attenuation effect due to atmospheric absorption and soft ground. The results of indoor and outdoor noise prediction for a recently constructed diesel engine power plant show good agreement with the measured.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1998.10a
• /
• pp.3-11
• /
• 1998

Response of tall buildings to near-field ground motions with distinct low-frequency pulses can differ dramatically from, for example, the response to the 1940 El Centro ground motion. For the same peak ground acceleration (PGA) and duration of shaking, ground motions with a pulse-like characteristic can generate much higher base shear, inter-story drifts and roof displacement in a high-rise building as compared to ground motions without the characteristic pulse. Also, the ductility demand is much higher and the effectiveness of supplemental damping is lower for pulse-like ground motions. This paper presents a simple interpretation of the response characteristics for two recorded and one synthetic near-field pulse-like ground motions.

• Steel and Composite Structures
• /
• v.27 no.4
• /
• pp.401-416
• /
• 2018

Composite beams with web openings are vulnerable to Vierendeel bending failure. The available methods provide quite conservative estimates of Vierendeel bending resistance. An alternative design method to compute the resistance was proposed in this study, based on quadratic nonlinear interactions of normalized shear force, axial force and Vierendeel bending moment. The interactions of the top and bottom Tee section must satisfy mutual conditions to prevent the Vierendeel failure. The normalized shear force and Vierendeel bending moment of the composite part were used instead in the top Tee interaction. The top Tee axial force was computed based on force equilibrium. Based on a rigid-plastic model, the composite resistance is estimated using an effective slab width of the vertical shear resistance. On using the proposed method, nonlinear reductions due to shear loads and axial forces are not required, in contrast to prior methods. The proposed method was validated against experiments from literature. The method limitations and accuracy as well as the Vierendeel behavior were investigated by finite element simulations, with varied composite beam parameters. The proposed design loads are less conservative than earlier estimates and deviate less from the simulations.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.2
• /
• pp.31-37
• /
• 1994

3-Dimensional panel method is now developed to the level that one can calculate the lift of a three dimensional body with the same accuracy of wind tunnel test and some current codes can consider the boundary layer effects due to the viscosity and unsteady motion in the calculation of lift. This paper is also aimed to develop these kinds of computing programs, and as a beginning, the authors restricted the problems to the steady potential flow cases. The calculation of 3-Dimensional body, wing and tandem wing carried out, using source panel and vortex ring panel. Finally, the interactions between 3-Dimension symmetric body and a wing are also calculated.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.479-481
• /
• 2016

This paper proposes the information service, which defines the agriculture product event structures and the ways to capture and share the standardized events based on GS1 standards. It is expected that agriculture business partners would reduce the cost to deal with heterogeneous agriculture product events with minimal mutual understanding.

• Journal of information and communication convergence engineering
• /
• v.19 no.1
• /
• pp.8-15
• /
• 2021

The Fourth Industrial Revolution is currently leading humanity into a super-connected, super-intelligent, and super-converged society through key technologies such as artificial intelligence, the Internet of Things (IoT), and big data. Blockchain technology has the potential to lead social innovation that will improve the mutual harmony and understanding of the complex structures of human society as well as various phenomena (e.g., antagonism, confrontation, and ideological conflict). With such progress in social innovation, blockchain technology will result in a fairer and more transparent human society. In addition, blockchain technology is emerging as a core infrastructure technology, and its growth and expansion are expected to bring about revolutionary improvements to nearly all fields of development and research. In this paper, we briefly outline the main features of blockchain technology. Through a further analysis of its ecosystem, we intend to offer suggestions for a more robust and efficient development of blockchain-related industries.

• Asia Marketing Journal
• /
• v.22 no.4
• /
• pp.103-116
• /
• 2021

This research outlines the motivations behind the fan-lead marketing and promotional endeavours undertaken by musical group BTS's fan community, also known as ARMY. In highlighting the reciprocity in intimacy between the group and their fans, I argue that ARMY's desire to elevate BTS is embedded within structures of affect, despite the financial nature of the benefits the group and their company may reap. These fan-lead initiatives represent efforts towards a common goal, where success, whether it comes in the form of money or not, is a gift of gratitude and a show of mutual understanding from fans to BTS. Based on data from 22 interviews with fans, this research explores the motivations behind fan-lead marketing by looking at the affective properties of music consumption, the parasocial relationship, fan community dynamics, and the purchase of intimacy. Within these contexts, the promotion surrounding BTS's music, as organized by the fans, mimics profit-oriented behaviours but is ultimately a gesture towards the exchange of intimacy between fans and artist.

• Journal of the Economic Geographical Society of Korea
• /
• v.6 no.1
• /
• pp.99-117
• /
• 2003

Major proposes of this study are to analyze Korean Shipbuilding's production network and cooperation between related firms and to understand their spatial features. The Geographical study about networks has focused on automobiles, electronics or communications industries. That's because those industries have distinctive spatial features thanks to the full growth of subcontract structures. The labor-centered, capital-centered shipbuilding industry, differently from other manufacturing industries, has production networks where outside trades are common. Today internet based communication is being reinforced and the flexibility of purchase circumstances is being positively proceeded. The central axes of the production network of Sumsung shipbuilding are internationally Europe and Asian area, nationally Busan and Gyeongnam province and Seoul Metropolitan areas, locally inside subcontracting firms. And In order to construct mutual trust with cooperation firms, Sumsung shipbuilding is trying to reinforce two-way cooperation relation through 'SungJoHoi' organized with outside subcontracting firms and 'inside cooperation firms conference'. In conclusion, Sumsung shipbuilding is trying to strengthen the competitiveness of shipbuilding industry, spatially by setting up the network through globalization-localization and functionally by constructing the partnership production network for mutual communication.