• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1853-1856
• /
• 2003

Multi-layer printed circuit board(PCB) is being used widely for the product with relatively complex circuits such as TV, VTR and FAX. With the rapid enlargement of electronic and IT industry, the hole machining technology on multi-layer PCB is increasingly required to improve. Thus, the micro drilling with ultrasonic vibration can be a good method for hole machining. Unlike conventional drilling, ultrasonic vibration applied drilling introduces less wear and fracture of not only tool but also internal surface of workpiece due to little cutting resistance, thus, machinability can be improved. The experiment is conducted through the comparison between the results of conventional drilling and ultrasonic micro drilling as well as among each results by the variation according to not only feed rate of drill but also amplitude and frequency of ultrasonic vibration. The multi-layer PCB consists of 6 layers and ${\Phi}$0.3 diameter drill was used. As a result, it was found that the state of internal surfaces of holes on multiple layer PCBs is improved by the application of ultrasonic vibration.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.65-70
• /
• 2018

M152, used for aircraft engine compressor cases, causes many problems in the cutting process due to its high hardness and high toughness. Characterized by a concave cylindrical center, aircraft engine compressor cases are thin but have multiple side holes to connect with internal parts. Thus, deformation occurs despite the jig sustaining the inside. The object of this study was to lessen the deformation arising from drilling by improving the drilling jig for aircraft engine compressor cases. To this end, an aircraft engine compressor case modeled with SolidWorks was analyzed with ANSYS under real conditions. Then, to secure reliability, the analyzed deformation was compared with the actual deformation. Based on the results, the effects of the improved drilling jig for aircraft engine compressor cases were verified.

• 대한정형외과 초음파학회지
• /
• 제5권2호
• /
• pp.66-74
• /
• 2012

목적: 만성 석회화 건염에 대한 보존적 치료방법으로 석회질 다발성 천공술과 체외 충격파 병합 치료의 효과를 비교하고, 체외 충격파 치료의 에너지 수준에 따른 임상적, 방사선학적 효과에 대하여 알아보고자 하였다. 대상 및 방법: 환자 선정은 2010년 6월부터 2011년 8월까지 어깨 통증으로 내원 후 극상근 만성 석회화 건염으로 진단받은 환자 98명을 대상으로 하였으며, 천공술 후 체외 충격파 치료를 에너지 수준에 따라 고에너지군(제 1군;31명), 저에너지군(제 2군;36명) 및 다발성 천공술 시행군(제 3군;31명) 으로 분류하였다. 보존적 치료에 반응하지 않고, 견관절 통증이 6개월 이상 지속되는 만성 석회화 건염 환자들만을 대상으로 하였다. 임상적 평가는 시술 전과 후 12주째 임상적 기능향상 및 증상 호전 정도를 ASES, KSS, CSS와 방사선학적 호전 정도를 석회화 결절의 크기 변화로 평가하였다. 결과: 세 군 모두에서 임상적 기능의 개선과 석회화의 감소가 나타났으며, 특히 임상적인 개선이 다발성 천공술만을 시행한 군(3 군)보다 추가적인 ESWT를 시행한 군(1, 2군)에서 매우 높게 나타났다. 또 방사선학적으로 볼 때, 석회화의 크기와 진행 속도는 통계적으로 유의하게 줄어들었다. 군간의 비교를 보면, 임상기능 개선의 정도와 석회화의 속도 감소의 차이는 고에너지 군(1군), 다발성 천공술(3군) 사이가 저에너지 군(2군), 다발성 천공술(3군)에서 보다 더 크게 나타났다, 그러나, 고에너지 군(1군)과 저에너지 군(2군)에서는 큰 차이가 없었다. 결론: 만성 석회화 건염의 치료를 위해, 추가적인 체외 충격파 치료는 다발성 천공술 단일로 시행했을 때보다 에너지 수준에 관계없이 임상적 기능의 개선과 석회화의 감소에 더 우수한 효과를 보여주었다. 그러나, 에너지 수준에 의한 체외 충격파 치료의 결과로, 석회화의 감소와 임상 기능 개선 정도에 대한 큰 차이가 없었다.

• 한국정밀공학회지
• /
• 제10권4호
• /
• pp.142-151
• /
• 1993

An intelligent mulitiple monitoring system to monitor tool/machining states synthetically was proposed and developed. It consists of 2 fundamental subsystems : the multiple sensor detection unit and the intellignet integrated diagnosis unit. Three signals, that is, spindle motor current, Z-axis motor current, and machining sound were adopted to detect tool/machining states more reliably. Based on the multiple sensor information, the diagnosis unit judges either tool breakage or degree of tool wear state using fuzzy reasoning. Tool breakage is diagnosed by the level of spindle/z-axis motor current. Tool wear is diagnosed by both the result of fuzzy pattern recognition for motor currents and the result of pattern matching for machining sound. Fuzzy c-means algorithm was used for fuzzy pattern recognition. Experiments carried out for drill operation in the machining center have shown that the developed system monitors abnormal drill/states drilling very reliably.

• 대한치과교정학회지
• /
• 제52권3호
• /
• pp.201-209
• /
• 2022

Objective: To compare the removal torque of microimplants upon post-use removal and post-retention removal and to assess the influencing factors. Methods: The sample group included 241 patients (age, 30.25 ± 12.2 years) with 568 microimplants. They were divided into the post-use (microimplants removed immediately after use or treatment) and post-retention (microimplants removed during the retention period) removal groups. The removal torque in both groups was assessed according to sex, age, placement site and method, and microimplant size. Pearson correlation and multiple linear regression analyses were performed for evaluating variables influencing the removal torque. Results: The mean period of total in-bone stay of microimplants in the post-retention removal group (1,237 days) was approximately two times longer than that in the post-use removal group (656.28 days). The removal torques in the post-retention removal group (range, 4-5 N cm) were also higher than those in the post-use removal group. The mandible and pre-drilling groups demonstrated higher placement and removal torques than did the maxilla and no-drilling groups, respectively. In the no-drilling post-use removal group, the placement torque and microimplant length positively correlated with the removal torque. In the post-retention removal group, unloading in-bone stay period and microimplant diameter positively correlated with the removal torque in the no-drilling and pre-drilling methods, respectively. Conclusions: The removal torques differed according to the orthodontic loading and removal time of microimplants. With prolonged retention of microimplants inserted using the no-drilling method, the removal torque was clinically acceptable and positively correlated with the unloading in-bone stay period.

• 대한족부족관절학회지
• /
• 제6권2호
• /
• pp.190-194
• /
• 2002

Purpose: We present our experience about the clinical aspect and treatment modalities of ostechondritis dissecans of the talus. Material and Method: This study included 35 patients, 38 cases diagnosed as ostechondritis dissecans of the talus that were proved by clinical and radiologic finding. The methods of treatment were conservative (2 cases), multiple drilling (1 case), excision (1 case), excision, curettage & multiple drilling (23 cases), curettage & bone peg fixation (2 cases), curettage & bone graft (2 cases), and autogenous osteochondral transfer(Mosaicplasty) (7 cases). Results: Of the 38 cases, 30 cases were associated with a history of trauma (17 cases of medial lesion, 13 cases of lateral lesion), and 9 cases of which had major trauma history and 21 cases, minor repetitive trauma history. According to O'Farrel grading system, 21 cases (55%) had good results, 11 cases (29%) had fair results, and 6 cases (16%) had poor results. Of the medial lesion 16 cases had good results, 6 cases, fair results, and 2 cases, poor results. Of the lateral lesion 5 cases had good results, 5 cases, fair results, and 4 cases, poor results. Conclusion: There were fair or good results in 84% of patients with surgical treatment. Curettage and multiple drilling reveals a good result in medial lesion in grade I, II, III and lateral lesion in grade I, II. Autogenous osteochondral transfer(Mosaicplasty) is considered for the cases in grade III, IV(medial and lateral), lesion exceeds 1Cm of size and poor result with another treatment modality.

• Steel and Composite Structures
• /
• 제36권4호
• /
• pp.417-426
• /
• 2020

Drilling processes in fiber-reinforced polymer composites are essential for the assembly and fabrication of composite structural parts. The economic impact of rejecting the drilled part is significant considering the associated loss when it reaches the assembly stage. Therefore, this article tends to illustrate the effect of cutting conditions (feed and speed), and laminate thickness on thrust force, torque, and delamination in drilling woven E-glass fiber reinforced epoxy (GFRE) composites. Four feeds (0.025, 0.05, 0.1, and 0.2 mm/r) and three speeds (400, 800, and 1600 RPM) are exploited to drill square specimens of 36.6×36.6 mm, by using CNC machine model "Deckel Maho DMG DMC 1035 V, ecoline". The composite laminates with thicknesses of 2.6 mm, 5.3 mm, and 7.7 mm are constructed respectively from 8, 16, and 24 glass fiber layers with a fiber volume fraction of about 40%. The drilled specimen is scanned using a high-resolution flatbed color scanner, then, the image is analyzed using CorelDraw software to evaluate the delamination factor. Multi-variable regression analysis is performed to present the significant coefficients and contribution of each variable on the thrust force and delamination. Results illustrate that the drilling parameters and laminate thickness have significant effects on thrust force, torque, and delamination factor.

• Archives of Plastic Surgery
• /
• 제34권3호
• /
• pp.409-412
• /
• 2007

Purpose: Percutaneous Kirschner wire fixation is common method for hand fracture. It is simple but has risk of ascending infection through the pin and bony injury by multiple drilling. Ascending infection through pin tract is mostly superficial and can be treated with antibiotics and aseptic dressing. This is a case review of subacute osteomyelitis on phalangeal bones after Kirschner wire fixation with literature review. Methods: A 40-years-old man with distal phalangeal fracture on right second finger is presented. He went to a local clinic and had percutaneous Kirschner wire fixation under local anesthesia. He was transferred to our hospital for ulcerative wound on DIP joint at 4 weeks after operation. Radiography showed osteolytic change around medulla of middle and distal phalanges, leading to diagnosis of a subacute osteomyelitis. We treated it with amputation at the level of shaft of middle phalanx. Results: The postoperative course was uneventful. We thought several possible reasons for osteomyelitis in our case. First, it could resulted from ascending infection through the wire. Second, it could be resulted from a bony burn by repeated drilling. And bony necrosis could be a consequence of arterial insufficiency caused by 2 pin insertion. Conclusion: We suggest that a precise pinning based on accurate anatomical understanding is required for a percutaneous Kirschner wire fixation. The frequency of drilling should be minimized. Careful observation and patient education for pin site care are essential.

• 한국산업보건학회지
• /
• 제1권1호
• /
• pp.47-55
• /
• 1991

Exposure level of respirable coal dust of underground coal mines in Taebaek area was evaluated. Personal air samplers with 10-mm nylone cyclones were attached to the coal workers including drillers, coal cutters, their assistants, haulers, and separators. Log-normality of respirable dust exposure concentration were tested by Kolmogorov-Smirnov one-sample test. Differences of means of respirable dust exposure concentration between work sites were tested by one-way ANOVA test and multiple comparison(Scheffe) test. And differences of respirable dust exposure concentration of principal and assistant workers in drilling sites and in coal faces were tested by paired t-test. Relation of respirable dust exposure concentration for the principal workers and their assistants in drilling sites and in coal faces were tested by regression analysis. The results were as follows : 1. All of the respirable dust concentration were log-normally distributed. 2. There were not only significantly different means of exposure concentration between drillers and coal cutters but between coal cutters and haulers. 3. Means of exposure concentration of drillers and drilling assistants were not significantly different. And means of exposure concentration of coal cutters and coal cutting assistants were not different.