• Journal of the Optical Society of Korea
• /
• v.12 no.3
• /
• pp.126-130
• /
• 2008

We propose and experimentally demonstrate an effective method to reduce near-field speckle noise at the output of a 50 ${\mu}m$ graded index multimode fiber using a short cylindrical piezoelectric transducer(PZT) vibrating in the radial direction. The fiber was coiled as tightly as possible around the mandrel of the PZT and a periodic stretching effect was caused by the radial oscillations of the actuator. The output of the optical fiber using the He-Ne laser source was intensively observed by a CCD camera. By counting all the pixels corresponding to relative intensity graded into 256 levels in the selected area and by calculating standard deviation and mean value of the intensity, we could measure the speckle contrast and vibration effect quantitatively with reduction ratio of pixels and line profile of the illuminated region. It was clearly observed that the characteristics of the speckle pattern in the vibration-on state were significantly improved over that of the vibration-off state due to time-averaged smoothing.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.136-142
• /
• 2006

This paper presents irradiance distribution model of light radiated from a step-index multimode optical fiber. The model is important in analysis of displacement response characteristics for intensity modulation type optical fiber sensors. The induced model was verified by experimental results. And the displacement response analysis result induced by using the irradiance distribution model was verified by experimental results and compared with using existing irradiance distribution models such as the constant model or the gaussian model. The experiment has better agreement with the analysis result using the induced model in this study than with the others models.

• Journal of information and communication convergence engineering
• /
• v.14 no.3
• /
• pp.163-170
• /
• 2016

Because of rapid technological advancements, increased data rate support has become the key criterion for future communication medium selection. Multimode optical fibers and multicore optical fibers are well matched to high data rate throughput requirements because of their tendency to support multiple modes through one core at a time, which results in higher data rates. Using the numerical mode solver OptiFiber, we have designed a concentric core fiber by investigating certain design parameters, namely core diameter (µm), wavelength (nm), and refractive index profile, and as a result, the number of channels, material losses, bending losses, polarization mode dispersion, and the effective nonlinear refractive index have been determined. Space division multiplexing is a promising future technology that uses few-mode fibers in parallel to form a multicore fiber. The experimental tests are conducted using the standard second window wavelength of 1,550 nm and simulated results are presented.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.12
• /
• pp.1900-1905
• /
• 1990

In this study, the thermal neutron effects on optical fiber are examined theoretically. Also, the induced loss by thermal neutron irradiation in optical fibers is measured at the optical wavelengths of 0.85 and 1.3\ulcorner, respectively, and the results are analyzed. Thermal neutrons cause nuclear reaction with fiber compositions. So secondary ionizing radiations of high energy are generated. Color centers formed by these secondary ionizing rasiations increase transmission loss of optical fiber by absorbing propagating light in fiber core. As a result of experiment, owing to Ge, P, and B doping effects, the induced loss in multimode fibers has been 5 tmes larger than that in single mode fibers at 1.3 \ulcorner wavelengh. In case of multimode fibers, the loss at 0.8 \ulcorner wavelength region more suceptible for radiations has been twice higher than at 1.3\ulcorner.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1123-1125
• /
• 1999

In this paper, we report a new scheme of multimode fiber sensor which uses pattern matching method. Fiber speckle pattern allows the wide dynamic range of the intensity based sensor. The proposed method uses pre-built specklegram database which is made by image processing techniques of wavelet transform and edge detection for the sake of compact data storage and fast sensing time. We demonstrate our proposed sensor and the experimental results will do presented.

• Journal of the Optical Society of Korea
• /
• v.9 no.2
• /
• pp.54-58
• /
• 2005

A novel mode analysis method and differential mode delay measurement technique for a multimode optical fiber based on optical frequency domain reflectometry has been proposed for the first time. We have used a conventional OFDR with a tunable external cavity laser and a Michelson interferometer. A few-mode optical multimode fiber was prepared to test our proposed measurement technique. The differential mode delay (DMD) of the sample fiber was measured to be 16.58 ps/m with a resolution of 1.5 ps/m. We have also compared the OFDR measurement results with those obtained using a traditional time-domain measurement method.

• Journal of the Optical Society of Korea
• /
• v.19 no.1
• /
• pp.7-12
• /
• 2015

Up to ${\sim}520{\mu}J$ broadband mid-infrared (IR) supercontinuum (SC) generation in telecommunication multimode fiber (MMF) directly pumped by a $2.054{\mu}m$ nanosecond Q-switched Tm, $Ho:YVO_4$ laser is demonstrated. An average output power of 3.64 W is obtained in the band of ~1900 to ~2600 nm, and the corresponding optic-to-optic conversion efficiency is 67% by considering the coupling efficiency. The spectrum has extremely high flatness with negligible intensity variation (<2%) in the wavelength interval of ~2070 to ~2475 nm. The SC long-wavelength edge is limited by the silicon glass material loss, and by optimizing the MMF length, the SC spectrum could extend out to ${\sim}2.6{\mu}m$. The output SC pulse shapes are measured at different output powers, and no splits are found. The SC laser beam is nearly diffraction limited with an $M^2=1.15$ in $2.1{\mu}m$ measured by the traveling knife-edge method, and the laser beam spot is monitored by an infrared vidicon camera.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.1
• /
• pp.129-135
• /
• 2003

Optical fiber has many advantages, such as high reliability, long lifetime, immunity to the electromagnetic interference, high speed response and low cost. In this study, we proposed and developed an optical fiber impact and pressure sensor for prevention of accident which occurs in the automatic system or auto door. The principle of the sensor is to detect different optical intensity caused by variation of a speckle pattern due to the external perturbation. Speckle pattern appears at the end of a multimode fiber in which coherent beam propagates. The fabricated sensor in this study was tested. As a result of experiments, amplitude of the output signal isn't linear, but it has sufficient sensitivity for a sensor. Moreover, we can control sensitivity of the sensor by an amplifier at receiver. It has several advantages which are ability of detection at all point on the multimode fiber, large sensitive area, and many application areas for a sensing impact and pressure.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.4
• /
• pp.696-700
• /
• 1987

Guide modes in a graded index multinmode optical fiber are turned into clad modes when the optical fiber was bended into a perpendicular direction to its optical axes by microbending forces, which causes the loss of the guiding optical power. The theories reported on this microbending power loss can be applied to calculation of the transmission power loss only when the beding period equals to the mode coupling length. In this paper, we obtained the general expression of the optical power transmission loss in a graded index multimode fiber bended periodically. This can be applied to the calculation of the power loss of the periodically microbended fiber with an arbitrary bending shape and period. Also, by using the beam theory in mechanics, we could derive the expression of the displacement of the optical fiber caused by the external force which bends the fiber into a periodic trapezoidal shape. Experiments were carried out to determine the dependence of the power loss on the period of the microbending forces. Experimnetal results were in good agreement (in the same order of the magnitude) with theoritical values derived in our work within the bending period region of 2mm-10mm.

• Korean Journal of Optics and Photonics
• /
• v.17 no.6
• /
• pp.500-506
• /
• 2006

An optical fiber displacement sensor has the advantages of relatively simplicity, cheap, small probe size and immunity against environmental perturbation. The working principle of the sensor is based on the intensity modulation that is detection light intensity reflecting from the surface being measured. This paper presents the mathematical model of displacement measurement mechanism of this sensor type. The theoretical and experimental data are compared to verify the model in describing the realistic approach to sensor design. Finally, the analysis results show that displacement response characteristics such as sensitivity, measuring range are easily modified by principal design parameters such as magnitude of optical Power, diameter of optical fiber core and distance between transmitting fiber and receiving fiber.