• Journal of Radiation Protection and Research
• /
• v.42 no.2
• /
• pp.91-97
• /
• 2017

Background: A gamma energy identifying algorithm using spectral decomposition combined with smoothing method was suggested to confirm the existence of the artificial radio isotopes. The algorithm is composed by original pattern recognition method and smoothing method to enhance the performance to identify gamma energy of radiation sensors that have low energy resolution. Materials and Methods: The gamma energy identifying algorithm for the compact radiation sensor is a three-step of refinement process. Firstly, the magnitude set is calculated by the original spectral decomposition. Secondly, the magnitude of modeling error in the magnitude set is reduced by the smoothing method. Thirdly, the expected gamma energy is finally decided based on the enhanced magnitude set as a result of the spectral decomposition with the smoothing method. The algorithm was optimized for the designed radiation sensor composed of a CsI (Tl) scintillator and a silicon pin diode. Results and Discussion: The two performance parameters used to estimate the algorithm are the accuracy of expected gamma energy and the number of repeated calculations. The original gamma energy was accurately identified with the single energy of gamma radiation by adapting this modeling error reduction method. Also the average error decreased by half with the multi energies of gamma radiation in comparison to the original spectral decomposition. In addition, the number of repeated calculations also decreased by half even in low fluence conditions under $10^4$ ($/0.09cm^2$ of the scintillator surface). Conclusion: Through the development of this algorithm, we have confirmed the possibility of developing a product that can identify artificial radionuclides nearby using inexpensive radiation sensors that are easy to use by the public. Therefore, it can contribute to reduce the anxiety of the public exposure by determining the presence of artificial radionuclides in the vicinity.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.65-65
• /
• 2011

Early-type galaxies represent the end point of galaxy evolution and, despite pervasive residual star formation, are generally considered "red and dead", that is composed exclusively of old stars with no star formation. Here, their molecular gas content is constrained and discussed in relation to their evolution, supporting the continuing importance of minor mergers and/or cold gas accretion. First, as part of the Atlas3D survey, the first complete, large, volume-limited survey of CO in normal early-type galaxies is presented. At least of 23% of local early-types possess a substantial amount of molecular gas, the necessary ingredient for star formation, independent of mass and environment but dependent on the specific stellar angular momentum. Second, using CO synthesis imaging, the extent of the molecular gas is constrained and a variety of morphologies is revealed. The kinematics of the molecular gas and stars are often misaligned, implying an external gas origin in over a third of all systems, more than half in the field, while external gas accretion must be shot down in clusters. Third, many objects appear to be in the process of forming regular kpc-size decoupled disks, and a star formation sequence can be sketched by piecing together multi-wavelength information on the molecular gas, current star formation, and young stars. Fourth, early-type galaxies do not seem to systematically obey all our usual prejudices regarding star formation (e.g. Schmidt-Kennicutt law, far infrared-radio continuum correlation), suggesting a greater diversity in star formation processes than observed in disk galaxies and the possibility of "morphological quenching". Lastly, a first step toward constraining the physical properties of the molecular gas is taken, by modeling the line ratios of density- and opacity-sensitive molecules in a few objects. Taken together, these observations argue for the continuing importance of (minor) mergers and cold gas accretion in local early-types, and they provide a much greater understanding of the gas cycle in the galaxies harbouring most of the stellar mass. In the future, better dust masses and dust-to-gas mass ratios from Herschel should allow to place entirely independent constraints on the gas supply, while spatially-resolved high-density molecular gas tracers observed with ALMA will probe the interstellar medium and star formation laws locally in a regime entirely different from that normally probed in spiral galaxies.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.587-590
• /
• 2012

Recently, the demand for the miniaturization of package substrates has been increasing. Technical innovation has occurred to move package substrate manufacturing steps into CMP applications. Electroplated copper filled trenches on the substrate need to be planarized for multi-level wires of less than $10{\mu}m$. This paper introduces a chemical mechanical planarization (CMP) process as a new package substrate manufacturing step. The purpose of this study is to investigate the effect of surfactant on the dishing and erosion of Cu patterns with the lines and spaces of around $10/10{\mu}m$ used for advanced package substrates. The use of a conventional Cu slurry without surfactant led to problems, including severe erosion of $0.58{\mu}m$ in Cu patterns smaller than $4/6{\mu}m$ and deep dishing of $4.2{\mu}m$ in Cu patterns larger than $14/16{\mu}m$. However, experimental results showed that the friction force during Cu CMP changed to lower value, and that dishing and erosion became smaller simultaneously as the surfactant concentration became higher. Finally, it was possible to realize more globally planarized Cu patterns with erosion ranges of $0.22{\mu}m$ to $0.35{\mu}m$ and dishing ranges of $0.37{\mu}m$ to $0.69{\mu}m$ by using 3 wt% concentration of surfactant.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.1
• /
• pp.90-97
• /
• 1996

The optimal mesh refinement has a meaning that error of the every element is within an allowable level and in uniformly distributed. The adaptive mesh generation may be required to achieve the optimal mesh generation. For the purpose of optimal mesh generation, an error estimation and an adaptive mesh refinement are required. Using the adaptive mesh generation the second finite element analysis is performed with the result of the first analysis. In the process the error estimation is required. In this study the adaptive mesh generation program for triangular element is developed, and for a posteriori error estimation the stress projection approach is considered. It has been found the multigrid technique, where the error estimation and the mesh generation are combined in multi-step of analysis, may be used efficiently in the finite element analysis.

• Archives of Pharmacal Research
• /
• v.25 no.2
• /
• pp.178-183
• /
• 2002

A high molecular ar weight water-soluble chitosan (WSC) with an average molecular weight of 300 kD and a deacethylation level of over 90% was produced using a simple multi-step-membrane separation process. It is known that WSC prevents obesity induced by a high-fat diet. Consequently, this study investigated whether or not WSC improved the ovarian dysfunction caused by obesity in mice. The mice were fed a high density protein and lipid diet for weeks, followed by the administration of WSC at 480 mg/kg body weight per day for 4 days. Thereafter, the changes in body weight, ovulation rate, in vivo and in vitro fertilization and emboryonic development were measured . WSC markedly reduced the body weight of obese mice fed with a high-fat diet, but not in mice fed with a normal diet. WSC had siginificant effects on the ovulation rate, both the in vivo and in vitro fertilization rates and embryonic development. These results indicate an improvement in the ovarian and oviduct dysfunction caused by obesity, and suggest an adjustment in the internal secretions and metabolic functions.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.4
• /
• pp.55-60
• /
• 2002

This paper presents a technique for the preparation of vertically grown CNTs by ICPHFCVD(inductively coupled plasma hot filament chemical vapor deposition) below $580^{\circ}C$. Purification of the CNTs(carbon nanotubes) using RE(radio frequency) plasma in a one step process, based on the different etching property of the Ni-tip, amorphous carbon and carbonaceous materials is also discussed. After purifying the grown materials. CNTs shown the multi walled and hollow typed structure. The typical outer and inner diameters or CNT were 50 nm and 25 nm, respectively. The graphitic wall was composed of 82 layers and the distance between wall and wall was 0.34 nm. From the results of TEM observation, the Ni catalyst at the tip of the carbon nanotubes were effectively removed by using a RF plasma etching, continuously.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4B
• /
• pp.298-305
• /
• 2003

In this paper, we proposed a high performance lookup controller for IP packet forwarding engine of ATM based label edge routers. The lookup controller is designed to provide services such as MPLS, VPN, ELL, and RT services as well as the best effort. For high speed searching for IP addresses, we employed a TCAM based hardware search device not using traditional algorithmic approaches. We also implement lookup control functions into FPGA for fast processing of packet header and lookup control. The proposed lookup controller is designed to support differenciated services for users and to process in pipelined mechanism for performance improvement. A two-step search scheme is also applied to perform lookup for the key combined with multi-field of packet header. We found that the proposed lookup controller provides the performance of about 16M packets per second through simulations.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.4
• /
• pp.699-707
• /
• 2023

DevSecOps is a concept that adds security procedures to the operational procedures of DevOps to respond to the short development and operation cycle. Multi-step vulnerability scanning process should be considered to provide reliable security while supporting rapid development and deployment cycle in DevSecOps. Many open-source vulnerability scanning tools available can be used for each stage of scanning, but there are difficulties in evaluating the security level and identifying the importance of information in integrated operation due to the various functions supported by the tools and different security results. This paper proposes an integrated security metric design plan for scurity results and the combination of open-source scanning tools that can be used in security stage when building the open-source based DevSecOps system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.39-46
• /
• 2016

This paper describes the third order feedforward delta-sigma modulator with inverter-based integrators and a 1.5bit comparator for the application of audio signal processing. The proposed 3rd-order delta-sigma modulator is multi-bit structure using 1.5 bit comparator instead of operational amplifier. This delta-sigma modulator has high SNR compared with single-bit 4th-order delta-sigma modulator in a low OSR. And it minimizes power consumes and simplified circuit structure using inverter-based integrator and using inverter-based integrator as analogue adder. The modulator was designed with 0.18um CMOS standard process and total chip area is $0.36mm^2$. The measured power cosumption is 28.8uW in a 0.8V analog supply and 66.6uW in a 1.8V digital supply. The measurement result shows that the peak SNDR of 80.7 dB, the ENOB of 13.1bit and the dynamic range of 86.1 dB with an input signal frequency of 2.5kHz, a sampling frequency of 2.56MHz and an oversampling rate of 64. The FOM (Walden) from the measurement result is 269 fJ/step, FOM (Schreier) was calculated as 169.3 dB.

• Korean Journal of Environmental Agriculture
• /
• v.33 no.4
• /
• pp.282-289
• /
• 2014

BACKGROUND: Methane($CH_4$) is considered as the secondmost potent greenhouse gas after carbon dioxide ($CO_2$). Methanogenesis is an enzyme-mediated multi-step process by methanogens. In the penultimate step, methylated Co-M is reduced by methyl Co-M reductase (MCR) to $CH_4$ involving a nickel-containing cofactor F430. The activity of MCR enzyme is dependent on the F430 and therefore, the bioavailability of Ni to methanogens is expected to influence MCR activity and $CH_4$ production in soil. In this study, different doses of EDTA(Ethylene Diamine Tetraacetic Acid) were applied in flooded soils to evaluate their suppression effect on methane production by chelating Ni of methanogenesis cofactor. METHODS AND RESULTS: EDTA was selected as chelating agents and added into wetland and rice paddy soil at the rates of 0, 25, 50, 75, and $100mmol\;kg^{-1}$ before 4-weeks incubation test. During the incubation, cumulative $CH_4$ production patterns were characterized. At the end of the experiment, soil samples were removed from their jars to analyze total soil Ni and water-soluble Ni content and methanogen abundance. Methane production from 100 mmol application decreased by 55 and 78% in both soils compared to that from 0 mmol. With increasing application rate of EDTA in both soils, water-soluble Ni concentration significantly increased, but total soil Ni and methanogen activities showed negative relationship during incubation test. CONCLUSION: The decrease in methane production with EDTA application was caused by chelating Ni of coenzyme F430 and inhibiting methanogenesis by methyl coenzyme M reductase. Consequently, EDTA application decreased uptake of Ni into methanogen, subsequently inhibited methanogen activities and reduced methane production in flooded soils.