• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.141-142
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.913-920
• /
• 1996

In this study, the counting method for multi-axial and multi-point load states was proposed. Using this counting method, the load spectrum is generated from the service load history which is measured for boom structure of excavator. Loading state for loading points of boom structure is described as a multi-dimensional state space. From this load spectrum, the stress spectrum was generated by FEM analysis using the superposition of the unit load. The cumulated damage at the severe damage point of In nm structure by the failure example is calculated by Palmgren-Miner's rule. As a result of this study, the fatigue life estimation using the multi-axial and multi-point load counting method is useful.

• Transactions of Materials Processing
• /
• v.13 no.2
• /
• pp.129-136
• /
• 2004

Recently, instead of a matched die forming method requiring a high cost and long delivery term, a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. Since the conventional multi-point dieless forming method has some disadvantages of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with an elasto-forming method has been suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of rubber and foam materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.21-28
• /
• 2003

Recently, instead of a matched die forming method requiring a high cost and long deliverly ten a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. As this multi-point dieless forming method has some disadvantage of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with elastomer forming was suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of a rubber and foam.

• Structural Engineering and Mechanics
• /
• v.83 no.2
• /
• pp.135-151
• /
• 2022

The generalized displacement method is a nonlinear solution scheme that follows the equilibrium path of the structure based on the development of the generalized displacement. This method traces the path uniformly with a constant amount of generalized displacement. In this article, we first develop higher-order generalized displacement methods based on multi-point techniques. According to the concept of generalized stiffness, a relation is proposed to adjust the generalized displacement during the path-following. This formulation provides the possibility to change the amount of generalized displacement along the path due to changes in generalized stiffness. We, then, introduce higher-order algorithms of variable generalized displacement method using multi-point methods. Finally, we demonstrate with numerical examples that the presented algorithms, including multi-point generalized displacement methods and multi-point variable generalized displacement methods, are capable of following the equilibrium path. A comparison with the arc length method, generalized displacement method, and multi-point arc-length methods illustrates that the adjustment of generalized displacement significantly reduces the number of steps during the path-following. We also demonstrate that the application of multi-point methods reduces the number of iterations.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.6
• /
• pp.22-27
• /
• 1997

In general, the load which acts on the structure is almost independent of time in many locations. In this case. It is difficult to estimate the life with the service load history, because the structure is on the multi- axial and multi-point loading states. In this study, the service load of the excavator which is widely used in industry field was calculated using measured cylinder pressures and displacements. The fatigue life was estimated using the multi-axial and multi-point load counting method. Service load history of 4 pin joint which act independently each other is yielded by mult-axial and multi-point load counting method. The stress spectrum is yielded by superposition of the results of FEM stress analysis applied unit load. Palm- gren-Miner's cumulative Damage is 0.000804 for Von Mises equivalent stress sequence by one side fillet weld S-N curve. This result agress with Bench test results. As a result of this study, the fatigue life esti- mation using the multi-axial and multi-axial and multi-point load counting method is useful.

• Structural Engineering and Mechanics
• /
• v.65 no.3
• /
• pp.263-274
• /
• 2018

In this study, we propose a frequency domain spectral element method (SEM) for the vibration analysis of a multi-span beam subjected to a moving point force. This study is an extension of the authors' previous study for a single-span beam subjected to a moving point force, where the two-element model-based SEM was applied. In this study, each span of a multi-span beam is represented by the Timoshenko beam model and the moving point force is transformed into the frequency domain as a series of each stationary point force distributed on the multi-span beam. The span at which a stationary point force is located is represented by two-element model, but all other spans are represented by one-element models. The vibration responses to a moving point force are obtained by superposing all individual vibration responses generated by each stationary point force. The high accuracy and computational efficiency of the proposed SEM are verified by comparing the solutions by SEM with exact analytical solutions by the integral transform method (ITM) as well as the solutions by the finite element method (FEM).

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.240-242
• /
• 2003

A method for performing two-dimensional lift-constraint drag minimization in inviscid compressible flows on unstructured meshes is developed. Sensitivities of objective function with respect to the design variables are efficiently obtained by using a continuous adjoint method. In addition, parallel algorithm is used in multi-point design optimization to enhance the computational efficiency. The characteristics of single-point and multi-point optimization are examined, and the comparison of these two method is presented.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.7 no.2
• /
• pp.91-100
• /
• 2011

Free viewpoint TV can provide multi-angle view point images for viewer needs. In the real world, But all angle view point images can not be captured by camera. Only a few any angle view point images are captured by each camera. Group of the captured images is called multi-view image. Therefore free viewpoint TV wants to production of virtual sub angle view point images form captured any angle view point images. Interpolation methods are known of this problem general solution. To product interpolated view point image of correct angle need to depth image of multi-view image. Unfortunately, multi-view video including depth image is necessary to develop a new compression encoding technique for storage and transmission because of a huge amount of data. Layered depth image is an efficient representation method of multi-view video data. This method makes a data structure that is synthesis of multi-view color and depth image. This paper proposed enhanced compression method using layered depth image representation and H.264/AVC video coding technology. In experimental results, confirmed high compression performance and good quality reconstructed image.

• Journal of Korea Multimedia Society
• /
• v.23 no.2
• /
• pp.166-173
• /
• 2020

Multi-view images, which are widely used for providing free-viewpoint services, can enhance the quality of synthetic views when the number of views increases. However, there needs an efficient representation method because of the tremendous amount of data. In this paper, we propose a method for generating point cloud data for the efficient representation of multi-view color and depth images. The proposed method conducts sequential reconstruction of point clouds at each viewpoint as a method of deleting duplicate data. A 3D point of a point cloud is projected to a frame to be reconstructed, and the color and depth of the 3D point is compared with the pixel where it is projected. When the 3D point and the pixel are similar enough, then the pixel is not used for generating a 3D point. In this way, we can reduce the number of reconstructed 3D points. Experimental results show that the propose method generates a point cloud which can generate multi-view images while minimizing the number of 3D points.