• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.13-18
• /
• 2007

When triple flames propagated in a diverging channel, the effects of fuel dilution on the lift-off characteristics of triple flames were investigated. A multi-slot burner was used to stabilize the lift-off flame especially at weak fuel concentration gradients. It was reported that there is a maximum propagation velocity at a critical concentration gradient in an open jet regardless of fuel dilution. The enhancement of a diffusion flame affected to increase the propagation velocity around critical concentration gradients. However, the influence of a confined channel on the structure of triple flames according to fuel dilution needs to be investigated compared with an open jet case. This study aimed to examine the effect of a confined channel on the structure and the propagation velocity of the triple flames according to fuel dilution. Lift-off height and propagation velocity of triple flames were investigated by employing three kinds of fuel compositions diluted by nitrogen (0%, 25%, 50% $N_2$), Fuel dilution reduced the propagation velocity of triple flame in a confined channel mainly due to the decrease of flame temperature in premixed branch. Despite the difference in fuel dilution, the propagation velocity has a maximum value at a specific fuel concentration gradient even though the critical concentration gradient increases with fuel dilution. And the critical concentration gradient in a confined channel is larger than that in an open jet due to enhancement of convective diffusion.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.39-48
• /
• 1983

This study was performed to obtain the basic data which could be used for the modification of the manual center-burner-type rice-husk furnace into a small scale automatic type for the multi-purpose use in the farm. For this purpose, first, the utilization feasibility of the rice-husk furnace in the farm was analyzed briefly in aspects of available amount of rice-husk for the fuel, annual operation time and replaceble amount of residential heating energy with rice-husk in the farm. For the experiment a prototype furnace geared with an automatic feeding device was fabricated, and feed rate, mold size and chimney height were changed to investigate the combustion efficiency of rice-husk and thermal efficiency of the furnace. Also, optimum and limiting operational factors were observed in each treatments. The results obtained are summarized as follows. 1. If the rice-husk is intensively used for residential heating in the farm for winter season, on an average 51 percent of the total heating energy can be replaced with the rice-husk. Therefore, development of a small scale automatic rice-husk furnace was recognized to be feasible. 2. The operational condition depending on husk-feed rates was very important factor for successive steady burning operation of the given furnace. When the feed-rate was 1.5 kg/hr, the top of the burning zone should be kept at the position about 55 cm from the bottom of the combustion chamber with the periodic removal of ash (termed as steady state position), which was 18 cm above the mold waist. When the feed rates were 2.4 kg/hr and 3.0 kg/hr, the steady state position was at about 4 cm above the mold waist. 3. The mold size affected inflow rate of air into the furnace and consequently CO content in the exhaust gas. The relatively bigger mold gave positive effect on the air-inflow rate. 4. When the husk-feed rates were 1.5 kg/hr, 2.4 kg/hr, 3.0 kg/hr, the combustion efficiencies of the rice-husk were 98.5%, 97.4% and 95.0%, the thermal efficiencies of the furnace were 93.4%, 93.2% and 87.6%, and CO content in the exhaust gas were 1.21%, 1.03%, and 2.43%, respectively. The air-inflow rates were decreased with the increase of feed rates. When the amount of excess air was 30-40%, the CO content in the exhaust gas was at the minimum level. 5. When the chimney height was lowered from 260 cm to 96 cm, the air-inflow rate was slightly decreased, but the average temperature in the combustion chamber, CO content in the exhaust gas and combustion and thermal efficiencies were not changed significantly. 6. The incidental problems associated with the protytype furnace were accumulation of the ash inside the mold, accumulation of the cinder between the outer-drum of the furnace and the combustion chamber wall, and accumulation of the cinder in the chimney.

• 한국조경학회지
• /
• 제38권5호
• /
• pp.113-121
• /
• 2010

노자공이 일본 아스카시대 궁원 남정을 만들었다는 수미산은 인도의 우주관에서는 성산(聖山:Sumeru),중국의 불교적 세계관에서는 묘고산(妙高山)의 형태를 상징화한 것으로 이해되며, 풍륜-수륜-금륜-지륜을 각각 4개의 돌조각에 조각한 조립형 석조물로 추정된다. 노자공의 수미산기록 외에, 일본서기 수미산 등장 4차례의 기록은 수미산이 옥외에 설치된 정원의 구성요소이자 주요 경물로서의 역할을 하였음을 시사하고 있다. 특히, 일본서기 기록의 문구와 그 표현으로 보아 수미산을 중심으로 경물들을 조합하여 활용한 것으로 판단되며, 모두 향연을 위한 특별한 행사시 활용되었던 것으로 보인다. 석신유적에서 발굴된 수미산석이 노자공이 오교와 더불어 만든 수미산인지는 현재 확인할 수 없으나, 이후 궁원의 정원시설물로 되풀이되어 조성된 '수미산형의 석조물'은 노자공이 황궁 남정에 조성한 수미산과 동일한 것이거나, 최소한 노자공이 만든 수미산을 원형으로 그 이후 재차 제작된 것으로 추정되며, 수미산을 기본으로 돌과 연못을 함께 이용하며 원지를 조성했을 것으로 추정된다. 따라서, 노자공이 오교와 함께 만들었다는 수미산은 불교의 수미산의 형상을 최대한 구상화한 형태인 동시에 축경수석이었다고 추정된다. 그리고 수미산의 외형과 기능을 수미산석으로 미루어 추정할 때, 수미산 표면의 문양은 백제시대에 제작된 백제금동대향로나 산수산경문전 그리고 활석제불보살병립상 후면의 문양에서 표현되고 있는 여러 겹으로 겹친 산악 문양 등의 도상과 매우 흡사하였을 것으로 판단된다. 또한, 수미산석의 형태 및 구조를 고려할 때 수미산석 분수시설에 적용된 원리는 수위 차에 따른 압력을 이용하는 사이펀(siphon)의 원리를 적용하여 물을 이동 분출한 것으로 보이며, 향연 등을 목적으로 한 실용수석 차원에서 만들어진 것으로 추정된다.