• New & Renewable Energy
• /
• v.7 no.4
• /
• pp.50-57
• /
• 2011

A wind turbine simulation program for the coupled dynamics of aerodynamics, elasticity, multi-body dynamics and controls of turbine is newly developed by combining an aero-elastic code and a multi-body dynamics code. The aero-elastic code, based on the blade momentum theory and generalized dynamic wake theory, is developed by NREL(National Renewable Energy Laboratory, USA). The multi-body dynamics code is commercial one which is capable of accounting for geometric nonlinearity and twist deflection. A turbulent wind load case is simulated for the NREL 5-MW baseline wind turbine model by the developed program and FAST. As a result, the two results agree well enough to verify the reliability of the developed program.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.402-407
• /
• 2002

A commercial CFD code is applied to analyze the 3-D viscous flow field within vertical multi-stage centrifugal pimp including impeller with 6 blades and guide vane with 11 blades and is performed by changing flow rate from 10 to $26\;m^3/h$ at the constant 3500rpm. The purpose of this 3-D numerical simulation is to confirm how much the effect of blade inlet angle of guide vane has an influence on the performance of vertical multi-stage centrifugal pimp. these results performed by $20^{\circ},\;30^{\circ}$ inlet angle of guide vane are compared with grundfos performance data. The vertical multi-stage pump consist of the impeller, guide vane, and cylinder. The characteristics such as total pressure coefficient total heat shaft horse power, power efficiency, discharge coefficient are represented according to flow rate changing.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.12-17
• /
• 2011

Gears are useful for power transmission due to excellent power transmission performance, low cost, and compactness. In addition, gears have constant speed ratio, compact structure, and excellent efficiency. In order to transmit higher power, the new multi-range transmission requires gears which have greater strength than the existing transmission. This study evaluates stability and durability through gear analysis of the multi-range transmission in commercial vehicles using ROMAX-DESIGNER program. Also, strength design evaluation is carried out by the analysis results which are compared with gear strength theory of AGMA standard. Bending stress and contact stress on gears are lower than their allowable stresses. Therefore, we can evaluate the safety of the gear strength design in multi-range transmission.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.589-592
• /
• 2002

A commercial CFD code is applied to analyze the 3-D viscous flow field within vertical multi-stage centrifugal pump including impeller of centrifugal pump with 6 blades and guide vain with 11 blades. The numerical analysis of vertical multi-stage centrifugal pump is performed by changing flow rate from $8\;to\;26\;m^{3}/h$ at the constant 3500rpm. The characteristics such as total pressure coefficient, total head, water horse power, power efficiency are represented according to flow rate changing. In the future, we will need to perform flow calculation of vertical multi-stage centrifugal pump by considering meridional shape of impeller.

• The Journal of the Korea Contents Association
• /
• v.11 no.12
• /
• pp.742-752
• /
• 2011

Multi-Level Marketing distribution process to reduce occurs in a number of the distribution costs to consumers of reducing its profits outside the area subject to the non-store or stores is the way to a special sale. Japan for the multi-level marketing Article 33 of the Act on Specified Commercial Transactions at or below the regulatory chain is defined as dealers. However, unlike other legislative attention two -dimensional chain for sales transactions are regulated. A chain of Japanese regulations on sales transactions, the definition is very specific and detailed regulations, and the chain is specifically for sales transactions in detail how to take regulatory and regulatory relief of pre- and post- regulatory focus, and the streamlining of regulatory aimed at restrictions on how the implications of such a large country.

• Culinary science and hospitality research
• /
• v.13 no.3
• /
• pp.158-165
• /
• 2007

This study was carried out to evaluate the rheological properties of cake flour with 3% of commercial multi-emulsifiers(P company, W company, O company) based on flour. Rheological properties were analyzed by Falling number, RVA, Alveograph and Farinograph. In Falling number, viscosity of cake flour with multi-emulsifiers was increased. In RVA, initial pasting temperature was increased by adding multi-emulsifier except for W company. and peak viscosity, final viscosity and setback were increased but breakdown was decreased. In Alveogram, P and P/L value were decreased but L and G value were increased. In Farinogram, water absorption was decreased but dough development time was increased and stability was increased except for P company.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.6
• /
• pp.429-436
• /
• 2010

Hydraulic experiments were conducted to analyze the characteristics of stem waves due to multidirectional random wave incidence with the different incident angles of main wave direction. Both multi-directional and uni-directional random waves were used to generate the stem waves and their results were compared with each other. The experiment shows multi-directional random waves developed along the vertical wall tend to increase as the incident angle increases similar to the uni-directional waves. Moreover, the stem wave widths were almost same as those in uni-directional random wave cases. However, the experiment demonstrate the stem wave heights were significantly smaller in multi-directional random wave cases than in uni-directional random wave cases.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.2
• /
• pp.153-159
• /
• 2012

This study gives the vertical motion analysis in multi-directional irregular waves using a commercial code(MAXSURF v.16) based on linear strip theory for a training ship. To verify the commercial code prior to the analysis, we guarantees the reliability of this paper's results using the commercial code by comparing with the results(Flokstra, 1974) of same hull and experimental conditions on a Panamax container. The analysis conditions are Beaufort wind scale No. 5($\bar{T}=5.46$, $H_{1/3}=2m$) based on ITTC wave spectrum, encounter angle Head & bow seas($150^{\circ}$) and Froude number Fn=0.257. Finally, we calculates heave RAO, pitch RAO and obtains the result of ship's response spectra for heave and pitch motions. In the motion response spectrum under the multi-directional irregular waves, heave motion reacts slightly high in short-crested waves and pitch motion reacts high in long-crested waves.

• Journal of Broadcast Engineering
• /
• v.12 no.4
• /
• pp.333-341
• /
• 2007

Multi-view video has recently gained much attraction from academic and commercial fields because it can deliver the immersive viewing of natural scenes. This paper presents multi-view video processing being composed of intermediate view reconstruction (IVR), graphics composition, and multi-view video viewer. First we generate virtual views between multi-view cameras using depth and texture images of the input videos. Then we mix graphic objects to the generated view images. The multi-view video viewer is developed to examine the reconstructed images and composite images. As well, it can provide users with some special effects of multi-view video. We present experimental results that validate our proposed method and show that graphic objects could become the inalienable part of the multi-view video.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.37-43
• /
• 2007

Recent technological developments in machine tools have been focused on high speed, low vibration machining and high precision machining. And the concern with multi-functional machining has been increased for the last several years. Multi-tasking machines are widely used in machine tool industries. Laser multi-tasking machine has been developed for high precision and fewer vibration machining. The purpose of this study is to evaluate the effects of structural reinforcement on Laser multi-tasking machine which is comprehensively combined turning center and laser machine. Up to date, for the structural stability evaluation of a multi-tasking machine, the analysis model has been considered only the weight of the upper parts. The positions of upper parts on multi-tasking machine have not been considered in the model. So, the results of the present FE model have revealed some difference with measurement data in case of multi-tasking machine. Design of the machine and structural analysis is carried out by FEM simulation using the commercial software CATIA V5. In the result of the structural analysis, effectiveness of reinforcement of the bed was confirmed.