• 한국실내디자인학회논문집
• /
• 제20권2호
• /
• pp.139-146
• /
• 2011

An attempt is made to illuminate the characteristics of Korean high-rise apartment plans built after the 1990s in Seoul. Unlike the typical slab block plans of the past century, these plans were accommodated in a super-highrise building which normally integrates some portion of commercial areas on the lower floors. Thus, they are much different from the pre-1990s plans, so needs to have different strategy to adapt to the Korean dwellers' domestic requirements. This study reveals the topological patterns that appear in these new plans, and tries to relate these patterns to the old configuration patterns of the slab-type apartment houses. From the analysis, it was found that some important Korean dwellers' characteristics are still preserved, but at the same time, some unprecedented patterns were beginning to be absorbed into the spatial arrangement. At the end, suggestions are made on how this emerging trend of super-high rise can be better understood and evolved to enhance the living quality in a new multi-unit setting.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1690-1695
• /
• 2007

Lightweight metallic truss structures with open, periodic cell are currently being investigated because of their multi-functionality such as thermal management and load bearing. The Kagome truss PCM has been proved that it has higher resistance to plastic buckling, more plastic deformation energy and lower anisotropy than other truss PCMs. The subject of this paper is an examination of the failure mechanism of Wire woven Bulk Kagome(WBK). To address this issue, the out-of-plane compressive responses of the WBK has been measured and compared with theoretical and finite element (FE) predictions. For the experiment, 2 multi-layered WBK are fabricated and 3 specimens are prepared. For the theoretical analysis, the brazed joints of each wire in WBK are modeled as the pin-joint. Then, the peak stress of compressive behavior and elastic modulus are calculated based on the equilibrium equation and energy method. The mechanical structure with five by five cells on the plane are constructed is modeled using the commercial code, PATRAN 2005. and the analysis is achieved by the commercial FE code ABAQUS version 6.5 under the incremental theory of plasticity.

• 한국지능시스템학회논문지
• /
• 제14권4호
• /
• pp.445-450
• /
• 2004

본 논문은 실질적인 최적화 구조물의 설계를 위한 시스템에 대한 것으로 퍼지이론에 바탕을 둔 자동 유한요소 생성 망 기술과 계산 기하학적 기술, 해석코드 및 솔리드모델러를 시스템에 통합시켰다. 최적해 또는 만족해는 자동해석 시스템과 함께 탐색공간을 위한 유전자 알고리즘을 이용하여 자동적으로 탐색되어 진다. 또한, 유전자 알고리즘을 이용함으로써 본 설계 시스템은 다차원 해를 얻을 수 있다. 개발된 시스템은 터널전류에 바탕을 둔 마이크로 가속도계의 형상설계에 적용하였다.

• 한국실내디자인학회논문집
• /
• 제22권1호
• /
• pp.283-290
• /
• 2013

The change of shopping environment created new emerging type of shopping center after 1990's, Urban Entertainment Center(UEC) in northen America. One hand traditional shopping center was retail-centered, the other hand UEC is entertainment-centered and offers the trinity of synergy. Each components, that are retail, dining and entertainment, play a role of drawing people, extending duration of visiting and making people revisit then the synergy makes commercial profit in shopping center. As northen America many of shopping centers with complex have been built in Korea since 2000 and some projects is planning by the change of shopping environment and regenerating urban. Although the term of "UEC" is used in Korea, it seems to be added entertainment facilities to shopping center without considering on commercial strategy. This study will take a look at mix and duration of visit which ULI stresses in UEC development and comparing with those of Yongsan Station and Chyeongrangri Station which are built recently in seoul, it will get characters and situation of these UECs. Finally, the analysis is to be used as a planning data in UEC development.

• 대한기계학회논문집A
• /
• 제38권2호
• /
• pp.115-120
• /
• 2014

본 연구에서는 다물체 동역학 해석 소프트웨어인 RecurDyn 을 이용하여 풍력 발전기를 쉽게 모델링하고 동적 거동 해석을 수행할 수 있는 기법을 개발하였다. 풍력 발전기는 타워, 너셀, 허브, 그리고 블레이드로 구성되어 있다. 타워와 블레이드는 탄성체로 가정하였고 탄성효과를 고려하기 위하여 탄성체 이론을 이용하여 모델링 하였다. 바람의 속도는 일정하다고 가정하였고 날개 요소 운동량 이론을 이용하여 공력하중을 모델링 하였다. 이를 통해 계산된 공력을 풍력 발전기에 적용시키고 동적 거동 해석을 수행하였다. 해석의 타당성을 검증하기 위하여 풍력 발전 시스템 상용 소프트웨어인 GH-Bladed를 이용한 해석결과와 비교하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.444-447
• /
• 2008

Recently, the need of thin-walled injection molding and enhancement of its productivity is greatly increased. In this study, we designed and manufactured a injection molding system, which can mold a part with the thickness of $500{\mu}m$ and 8 cavity. And processing technique for the multi-cavity injection molding system, which is capable of mass productivity on the plastic parts, was considered. The problems of unbalance/imbalance on the molding process for the multi-cavity mold were predicted by numerical analysis using plastic injection molding commercial code. In addition, controllable system of melt front filling was introduced for a balanced filling using the mold temperature sensor on injection mold. It was shown that balanced filling with the suggested injection molding system was possible for $500{\mu}m$ plastic parts with 8 cavity layout.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권1호
• /
• pp.3-8
• /
• 2006

This paper deals with an automated computer-aided process planning and die design system by which designer can determine operation sequences even if they have a little experience in process planning and die design for axisymmetric products. An attempt is made to link programs incorporating a number of expert design rules with the process variables obtained by commercial FEM softwares, DEFORM and ANSYS, to form a useful package. The system can provide a flexible process based on either the reduction in the number of forming sequences by combining the possible two processes in sequence, or the reduction of deviation of the distribution on the level of the required forming loads by controlling the forming ratios. Especially in die design module optimal design technique and horizontal split of die insert were investigated for determining appropriate dimensions of components of multi-former die set. Results obtained, using the modules, enable the design and manufacture of a die set for a multi-former to be more efficiently performed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1897-1900
• /
• 2004

In recent years, a lot of industrial equipments have serial communication channel such as FieldBus (CAN, Profibus, etc.) or Ethernet that provides real time communication between industrial equipments. Theses applications include gantry crane, robot, chip mounter, etc.. In this paper, we discuss the synchronization technique for networked multi-motor systems where controllers (commercial servo amps) are distributed and interconnected by CAN (Controller Area Networks). We first describe the equivalent model for the individual servo-amp and motor using the frequency response. We design the $H{\infty}$ controller for motion synchronization. Finally, the synchronization technique using the equivalent model and the $H{\infty}$ controller is verified by the simulation and the experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.360-365
• /
• 2003

In this paper, we have developed a general purpose motion controller using an FPGA(Field Programmable Gate Array). The multi-PID controllers on a single chip are implemented as a system-on-chip for multi-axis motion control. We also develop a PC GUI for an efficient interface control. Comparing with the commercial motion controller LM 629 it has multi-independent PID controllers so that it has several advantages such as space effectiveness, low cost and lower power consumption. In order to test the performance of the proposed controller, robot finger is controlled. The robot finger has three fingers with 2 joints each. Finger movements show that position tracking was very effective. Another experiment of balancing an inverted pendulum on a cart has been conducted to show the generality of the proposed FPGA PID controller. The controller has well maintained the balance of the pendulum.

• International journal of advanced smart convergence
• /
• 제8권4호
• /
• pp.200-206
• /
• 2019

In this study, we compared the VacCAD and VacSim^(Multi), commercial vacuum simulators, to verify the advantages of VacCAD's efficiency. It was emphasized on immediacy and simplicity of simulation modelling, and characteristics of the pump combinations, pumping down curves, and vacuum materials. First, usability of simulation mechanism was estimated through the modeling schematics and obtained simulation results of each employed simulator were compared to evaluate the applicability in practice. Simulation reliability of each simulator was also probed by comparing the pumping characteristics of commercially available high vacuum systems. In addition, the degree of tolerances on VacCAD was also investigated through pumping down analysis considering outgassing effect due to chamber material variations. The higher effectiveness and expediency of VacCAD than VacSim^(Multi) has been presented, and it was expected that the utilization of VacCAD in vacuum applications to be increased.