• Journal of Welding and Joining
• /
• v.32 no.2
• /
• pp.29-36
• /
• 2014

Recently, in order to enhance the function and usefulness of products, cladding of dissimilar materials that maximizes the performance of the material is being widely used in all areas of industry as an important process. Clad steel plate, produced by cladding stainless steel plate, an anticorrosive material, on carbon steel plate, is being used to produce pressure vessels. Stainless steel plate has good corrosion resistance, and carbon steel plate has good rigidity and strength; clad steel can satisfy all of these qualities at once. This study aims to find the ${\delta}$-ferrite behavior, mechanical properties, structure change, integrity and reliability of clad steel weld on hot rolled steel plates. For this purpose, multi-layer welding, repair welding and post weld heat treatment were implemented according to welding procedure specifications (WPS). In order to observe the mechanical properties and toughness of clad steel weld zone, post weld heat treatment was carried out according to ASME Sec. VIII Div.1 UW-40 procedure for post weld heat treatment. With heat treatment at $625^{\circ}C$, the hold time was used as the process variable, increased by intervals that were doubled each time, from 80 to 1,280 min. The structure of weld part was typical cast structure; localized primary austenite areas appeared near central vermicular ferrite and fusion line. The heat affected zone showed rough austenite structure created by the weld heat input. Due to annealing effects of heat treatment, the mechanical properties (tensile strength, hardness, impact value) of the heat affected area tended to decrease. From the results of this study, it is possible to conclude the integrity of clad steel welds is not affected much in field welding, repair welding, multi-layer welding, post weld heat treatment, etc.

• Spatial Information Research
• /
• v.18 no.3
• /
• pp.1-11
• /
• 2010

Recently, the construction of three dimensional spatial information of Dam reservoir area is very important part in Dam management work such as sediment survey, but it is difficult to acquire detailed terrain data because totalstation and single beam echo sounder are applied to terrain survey. This study presented method to construct detailed terrain data of Dam reservoir area using LiDAR and multi beam echo sounder. First, LiDAR survey was carried out in land zone and calibration process was applied by ground control point. And also the DEM of land zone was constructed by using algorithm, which eliminated building and vegetation class. As the result of validation of LiDAR DEM using GPS terrain survey, it was possible to construct three dimensional terrain data that was satisfied with the tolerance error of LiDAR, which was the standard error of LiDAR DEM showed as 0.108m. Also multi beam echo sounder was applied to the survey of water zone and it could construct spatial information that was satisfied with bathymetry surveying tolerance error of International Hydrographic Organization by validation with terrain survey data. And LiDAR and multi beam echo sounder data were integrated and it was possible to construct three dimensional spatial imagery information that can be applied to Dam management work such as the estimation of sediment amounts or the monitoring of terrain change by linking with high resolution orthophoto.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2301-2306
• /
• 2011

Current general-purpose electromagnetic field simulators have been widespread applied, and is being used to electromagnetic problems such as antenna design, EMC design, measurement, and microwave device design, etc. This paper is to solve various electromagnetic problems in X-band region for utilizing multi-core-based PC available network resources more efficiently. The electromagnetic field simulator based on TCP / IP-based network topology, configuration, and its framework design is proposed and its availability is examined.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.1165-1168
• /
• 2005

The video device is used to gain lots of informations in indoor environment. The one of informations is the information to identify the moving object. The methods to identify the moving object are to recognize the face, the gait and to analyze the hue histogram of the clothes. The hue data is effective at the environment of multi-video. In this paper, we describe the existing research about to identify the moving object in the environment of multi-video and find its problems. finally, we present the enhanced methods to solve its problems. In the future, the method will be use for recognizing the location of object in ubiquitous home.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.821-825
• /
• 2000

Drawing is one of the oldest metal forming operations and has major industrial significance. This process allows excellent surface finishes and closely controlled dimensions to be obtained in long products that have constant cross sections. In drawing of the high carbon steel wire, exit speeds of several hundreds meters per minute are very common. Drawing is usually conducted at room temperature using a number of passes or reductions through consequently located dies. In multi-stage drawing process like this, temperature rise in each pass affects the mechanical properties of final product such as bend, twist and tensile strength. In this paper, therefore, to estimate the wire temperature in multi-stage wire drawing process, wire temperature prediction method was mathematically proposed. Using this method, temperature rise at deformation zone as well as temperature drop between die exit and the next die inlet were calculated.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1141-1151
• /
• 2016

This study proposes a novel islanding detection method for distributed photovoltaic (PV) systems with multi-inverters based on a combination of the power line carrier communication and Sandia frequency shift islanding detection methods. A parameter design method is provided for the novel scheme. On the basis of the designed parameters, the effect of frequency measurement errors and grid line impedance on the islanding detection performance of PV systems is analyzed. Experimental results show that the theoretical analysis is correct and that the novel method with the designed parameters has little effect on the power quality of the inverter output current. Non-detection zones are not observed, and a high degree of reliability is achieved. Moreover, the proposed islanding detection method is suitable for distributed PV systems with multi-inverters.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.399-404
• /
• 2006

Heating and cooling load of ventilation is a very important part of building energy saving. Improving ventilation effectiveness can save building energy consume and supply fresh air to indoor efficiently. So this study measured mulity-zone aiflow and ventilation effectiveness according to ventilation types. Result of measurement show that ventilation effectiveness is depends on ventilation system design rather than ventilation types.

• Journal of KIISE:Information Networking
• /
• v.35 no.6
• /
• pp.521-528
• /
• 2008

Such conventional maritime communication technologies as radio have short some comings in their transmission quality. It can be overcome by wireless channels provided by satellites such as INMARSAT, which nevertheless suffer from the high costs. In this paper, we propose a novel technology resolving the above problems, featuring in the establishment of maritime communication networks with multi-hop structures. The inter vessel and ship-to- shore networks previously modeled after MANET are remodeled by SANET (Ship Ad Hoc Networks) in the present work. Fan-shaped Search Zone Routing (FSR) protocol also is presented, which utilizes not only static geographical information including the locations of ports and the navigations of courses but also the unique characteristics of ships in terms of mobile nodes. The FSR finds the fan-shaped search zone on which the shortest path is located. The performance of LAR protocol is compared with that of FSR in several ways. First, FSR does not make use of a type of control packets as beaconing data, resulting in a full utilization of the bandwidth of the wireless channels. Second, the delivery rate by the FSR is 100% for the fan-shaped search zone includes at least one route between source and destination nodes on its border line, where as that of LAR has been turned out to be 64%. Third, the optimality of routes searched by the FSR is on a 97% level. Of all, the FSR shows a better performance than LAR by about 50%.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.2
• /
• pp.29-35
• /
• 2011

In order to effectively control waves in a coastal zone, Multi-Cylinder Piles have been suggested as economic structures. A numerical analysis was conducted using the Delft-3D: WAVE module based on SWAN, which considered wave shoaling and refraction. Moreover, irregular waves were used to investigate the hydrodynamic characteristics of the wave interaction with the structure. In this paper, a numerical analysis was carried out to research the effect of wave control through a wave height analysis concerning an existing, concrete wave breaker and multi-cylinder piles placed at the same location. As a result, the effect of the wave control is shown using the wave breaker, multi-cylinder piles, and existing data.

• Journal of Information Display
• /
• v.3 no.3
• /
• pp.1-11
• /
• 2002

Multi-view function is important to three-dimensional displays without dedicated glasses. It is the reason that the observers earnestly desire to change their positions freely. Multi-viewing is also principal to the reality of three-dimensional (3D) image displayed on the screen. The display of projection type has the advantage that the number of viewing points can be easily increased according to the number of projectors. The authors research on multi-view projection display with hologram screen. Powerful directionality of the diffracted beam from hologram screen is required unlike two-dimensional (2D) display. We developed a new method that all diffracted beams satisfied the same Bragg condition and became sufficiently bright to observe the 3D image under usual indoor light. The principle is based on the essential Bragg diffraction in the three-dimensional space. Owing to such three-dimensional Bragg diffraction we achieved an excellent hologram screen that could be multiple reconstructed in spite of single recording. This hologram screen is able to answer arbitrary numbers of viewing points within wide viewing zone. The distortion of 3D image becomes also sufficiently small with the method of dividing the cross angle between illumination and diffraction beam.