• 한국세라믹학회지
• /
• 제29권9호
• /
• pp.719-728
• /
• 1992

ZrO2/Al2O3-Mullite composites were prepared by infiltration of the silica sol to the porous ZrO2/Al2O3 bodies. The porous ZrO2/Al2O3 bodies for infiltration were fabricated using ZrO2 (20wt%)/Al2O3 composite powders synthesized by the emulsion-hot kerosene drying method. The preparation of silica sols was conducted by the hydrolysis-peptization of an alcoholic TEOS solution. When ZrO2/Al2O3-Mullite and ZrO2/Al2O3 composites were sintered at 1$650^{\circ}C$ for 4 hrs, both of them showed an excellent sinterability. As the amount of mullite added in the composites increased, the ratio of the tetragonal phase of zirconia to the monoclinic phase at the room temperature became higher. It was known that values of the fracture toughness of the ZrO2/Al2O3-Mullite composites were about 5.48 MPa.m1/2 much larger than that of the ZrO2/Al2O3 system.

• 한국세라믹학회지
• /
• 제27권2호
• /
• pp.201-210
• /
• 1990

The mullite-15v/o ZrO2 composites were prepared by dispersing ZrO2-3m/o Y2O3 powders into the mullite matrix in order to improve the mechanical properties of the mullite. The densification and retention of t-ZrO2 in the matrix of synthetic mullite were also investigated. From IR spectroscopic analysis, the obtained amorphous SiO2-Al2O3 powder was observed to have Si-O-Al chemical bond in its structure which might result in the homogeneous mullite composition. The lattice parameter of the mullite powder calcined above 130$0^{\circ}C$ (a0=7.5468$\AA$) is nearly close to the value of stoichiometric mullite (71.8wt% Al2O3, a0=7.5456$\AA$). The sintering behavior, microstructure, flexural strength and fracture toughness of the mullite and mullite-15v/o ZrO2 composites have been studied. The mullite-15v/o ZrO2(+3m/o Y2O3) ceramics with relative densities of 96% were obtained when sintered at 1$600^{\circ}C$. The flexural strength and fractrue toughness of the composites sintered at 1$600^{\circ}C$(calcination temperature of mullite powders ; 125$0^{\circ}C$) had maximum values of 307MPa and 2.50MPa.m1/2, respectively. The fracture toughness improvement in the mullite-ZrO2 cmoposite is assumed to be resulted from the combined effect of the stress-induced phase transformation of tetragonal ZrO2 and the crack deflection due to microcracking by the monoclinic ZrO2 formation.

• 한국분말재료학회지
• /
• 제4권1호
• /
• pp.9-17
• /
• 1997

The mullite-zirconia composites were prepared by the pressureless sintering with addition of 10~20 vol% ZrO$_2$(TZ3Y) in the fused mullite and sol-gel mullite matrix. The densification rate of sol-gel mullite was higher than that of fused mullite, and the addition of ZrO$_2$(TZ3Y) was effective on the densification of fused mullite. The enhancement of densification and anisotropic growth of mullite in ZrO$_2$added specimen can be explained by the solid solution effect of $Zr^{+4}$ ion in mullite. Both mechanical strength and fracture toughness of mullite-zirconia composite were enhanced compared to those of mullite. The enhancement of mechanical properties is attributed to the hinderance of grain growth and the combined toughening effects of tetra-mono phase transformation and crack deflection due to the residual stress between mullite/ZrO$_2$.

• 한국세라믹학회지
• /
• 제36권10호
• /
• pp.1080-1086
• /
• 1999

Mullite/zirconia composite was synthesized by adding zirconia and Zircon to mixture of Hapcheon kaolin(grade pink A) and aluminium nitrate salt in order to enhance strength of the mullite specimens. Kaolin and aluminium nitrate salt was mixed milled and calcined at 100$0^{\circ}C$ and then 5wt% mullite seed was added to increase mullite content. The influence of the additives(ZrO2 and ZrSiO4) and sintering temperature on the strength of the sintered specimens was investigated. The flexural strength of the specimens containing 10wt% zirconia was enhanced from 150MPa without the additive up to 300MPa after heat treatment at 156$0^{\circ}C$ In the case of addition of 15wt% zircon the strength of the specimens systhesized at 1$600^{\circ}C$ was 225 MPa.

• 한국재료학회지
• /
• 제28권12호
• /
• pp.719-724
• /
• 2018

Cordierite composed of an alumina-silica-magnesia compound has a low coefficient of thermal expansion(CTE) and excellent thermal shock resistance. It also has a low dielectric constant and high electrical insulation. However, due to low mechanical strength, it is limited for use in a ceramic heater. In this study, $ZrO_2$ is added to an 80 wt% cordierite-20 wt% mullite composition, and the effect of $ZrO_2$ addition on the mechanical strength and thermal shock resistance is investigated. With an increasing addition of $ZrO_2$, cordierite-mullite formed $ZrO_2$, $ZrSiO_4$ and spinel phases. With sintering conducted at $1400^{\circ}C$ with the addition of 5 wt% $ZrO_2$ to 80 wt% cordierite-20 wt% mullite, the most dense microstructure forms along with an excellent mechanical strength with a 3-point flexural strength of 238MPa. When this composition is quenched in water at ${\Delta}T=400^{\circ}C$, the 3-point flexural strength is maintained. Moreover, when this composition is cooled from $800^{\circ}C$ to air, the 3-point flexural strength is maintained even after 100 cycles. In addition, the CTE is measured as $3.00{\times}10^{-6}{\cdot}K^{-1}$ at $1000^{\circ}C$. Therefore, 80 wt% cordierite-20 wt% mullite with 5 wt% $ZrO_2$ is considered to be appropriate as material for a ceramic heater.

• 한국세라믹학회지
• /
• 제37권5호
• /
• pp.497-504
• /
• 2000

In this study, mullite-zirconia comosite was fabricated by adding ZrOCl2.8H2O using of boehmite gel coating to Hadong kaolin (pink A grade) in order to enhance strength of the mullite specimens. The influence of ZrOCl2.8H2O content and fireing temperature on the crystall phase, microstructure, bulk density, strength of the specimens was investigated. Mullite-zirconia composite was produced in the process of coating zirconia to mullite powder synthesized thereafter and mixing simultaneously of starting materials with boehmite-zirconia gel. Maximum strength with in this study was 251 sintered at 1$600^{\circ}C$ for 2h. Bulk density and strength of the composite with zirconia coated mullite was higher than simultaneous on mixture of starting materials.

• 한국재료학회지
• /
• 제5권7호
• /
• pp.888-896
• /
• 1995

Al 금속분말을 zircon sand (ZrSiO$_4$)와 A1$_2$O$_3$혼합체에 첨가하여 반응소결시킴으로써 무수축 Mullite-ZrO$_2$, 요업체를 얻고자 하였다. 반응식, 3(Al+Al$_2$O$_3$)+2ZrSiO$_4$$\longrightarrow$3A1$_2$O$_3$ .2SiO$_2$+2ZrO$_2$에 의하여 ZrO$_2$-강화 Mullite 요업체를 제조하였다. Al 분말은 A1$_2$O$_3$에 대해 0-30 무게 퍼센트까지 대체하였다. 평량한 분말을 볼밀하여 혼합 분쇄한 후, 정수압 성형하여 시편을 제조하고, 온도범위 1450-1$600^{\circ}C$에서 3시간 반응소결시켰다. Al의 충분한 산화를 위해, 한편으로는 125$0^{\circ}C$에서 5시간동안 열처리를 거친후 소성온도로 올리기도 했다. Al을 첨가함으로서 반응은 촉진되었으며, 소성수축도 산화한 Al의 부피팽창에 의해 상쇄되어, 무수축요업체 제조의 가능성을 보였다. 박편모양을 한 비교적 큰 Al분말이 잘 분쇄되지 않음으로 해서, Al이 자리했던 곳에 큰 기공을 남겼다.

• 한국세라믹학회지
• /
• 제52권6호
• /
• pp.423-428
• /
• 2015

The machinability of materials is an important factor in engineering applications. Many ceramic components that have complex shapes require machining, typically using diamond tools, which leads to high production cost. Machinable ceramics containing h-BN have recently been developed, but these materials are very expensive because of high cost of raw materials and machining. Therefore the development of low-cost machinable ceramics is desirable. In this study, mullite-$ZrO_2$ ceramics were prepared additions of $Al_2TiO_5$. $ZrSiO_4$, $Al_2O_3$, and $Al_2TiO_5$ powders mixed at various molar ratios with sintering at 1400, 1500, and $1600^{\circ}C$ for 1 hr. Phase formation and microstructure of the sintered ceramics were observed by XRD and SEM, respectively. The machinability of each specimen was tested using the micro-hole machining method. The machinability results show that the ceramics sintered at temperatures over $1500^{\circ}C$ can be used as good low-cost machinable mullite-$ZrO_2-Al_2TiO_5$ ceramics.

• 한국세라믹학회지
• /
• 제28권5호
• /
• pp.399-405
• /
• 1991

Mullite-PSZ powders were synthesized by the sol-gel process using Al(sec-OC4H9)3, Si(OC2H5)4, ZrOCl2$.$8H2O and YCl3 solution and the characteristics of synthesized powders were studied. The sinterability and mechanical properties of powder compacts sintered at 1670$^{\circ}C$ for 4hr were also studied for various PSZ contents. ${\gamma}$-Al2O3(Al-Si spinel) formed at 980$^{\circ}C$ from amorphous dried gel, and mullite as well as ZrO2 formed above 1200$^{\circ}C$. At the room temperature, ZrO2 was a mixture of tetragonal and monoclinic phases. The specimens were densified to 97∼98% except the specimen containing 25 vol% PSZ which showed the relative density of 94%. The K1c value increased with the PSZ content and showed a maximum value of 4.1 MN/m3/2 at 25 vol% PSZ; this value was about 50% higher than that of the mullite without PSZ. Flexural strength had a maximum value of 280 Mn/㎡ at 20 vol% PSZ. In contrast, at 25 vol%, the flexural strength was even lower than that of the mullite possibly due to higher porosity of 6%.

• 한국세라믹학회지
• /
• 제37권2호
• /
• pp.174-180
• /
• 2000

Y-TZP/mullite composites were prepared by the infiltration of Y-TZP precursor into partially reaction-sintered mullite. The addition of Y-TZP(~7.2 wt%) increased the bend strength(207 MPa), fracture toughness(4.6MPa.m1/2) and Vickers microhardness(853kg/$\textrm{mm}^2$) of the uninfiltrated mullite sintered at 162$0^{\circ}C$ for 10h by more than 75, 70 and 105%, respectively. Residual alumina-rich glass was observed at a mullite/mullite junction, due to the mullitization reaction of silica melt with crystalline $\alpha$-Al2O3 during a final sintering. Although ZrO2 inclusions improved the final sintered density of mullite they did not effectively prevent its grain growth.