• Korean Journal of Materials Research
• /
• v.15 no.8
• /
• pp.518-520
• /
• 2005

Effects of the $O_2/Ar$ flow ratio in the sputtering process on the crystallinity, surface roughness, carrier concentration, carrier mobility, and optical properties of Al-doped ZnO thin films deposited on sapphire (001) substrates by RF magnetron sputtering were investigated. XRD spectra showed a preferred orientation along the c-axis and a minimum FWHM of the (002) XRD intensity peak for the $O_2/Ar$ flow ratio of 0.5. The (101)peak also appeared and the degree of preferred orientation decreased as the $O_2/Ar$ flow ratio increased from 0.5 to 1.0. AFM analysis results showed that the surface roughness was lowest at the $O_2/Ar$ flow ratio of 0.5 and tended to increase owing to the increase of the grain size as the $O_2/Ar$ flow ratio increased further. According to the Hall measurement results the carrier concentration and carrier mobility of the fan decreased and thus the resistivity increased as the $O_2/Ar$ flow ratio increased. The transmittance of the ZnO:Al film deposited on the glass substrate was characteristic of a standing wave. The transmittance increased as the $O_2/Ar$ flow ratio in-RF magnetron sputtering increased up to 0.5. Considering the effects of the $O_2/Ar$ flow ratio on the surface roughness, electrical resistivity and transmittance properties of the ZnO:Al film the optimum $O_2/Ar$ flow ratio was 0.5 in the RF magnetron sputter deposition of the ZnO:Al film.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.477-480
• /
• 2015

In this paper a low-voltage vibration energy harvesting circuit with MPPT(Maximum Power Point Tracking) control is proposed. By employing bulk-driven technique, the minimum operating voltage of the proposed circuit is as low as 0.8V. The designed MPPT control circuit traces the maximum power point by periodically sampling the open circuit voltage of a full-wave rectifier circuit connected to the piezoelectric device output and delivers the maximum available power to load. The proposed circuit is designed using a $0.35{\mu}m\;CMOS$ process, and the chip area including pads is $1.33mm{\times}1.31mm$. Simulation results show that the maximum power efficiency of the designed circuit is 85.49%.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.405-408
• /
• 2013

The performance of underwater acoustic(UWA) communication system is sensitive to the Inter-Symbol Interference(ISI) due to delay spread develop of multipath signal propagation. And due to limited frequency using acoustic wave, UWA is a low transmission rate. Thus, it is necessary technique of Space-time code, equalizer and channel code to improve transmission speed and eliminate ISI. In this paper, UWA communication system were analyzed by simulation using these techniques. In the result of simulation, the proposed Space-time code, Turbo code, and Zero forcing techniques is shown that improved performance than conventional UWA communication.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.3
• /
• pp.142-145
• /
• 2015

In this work, open stubs were fabricated on a polyether sulfone (PES) substrate, and their basic radio frequency (RF) characteristics were investigated for application to RF matching components of a flexible monolithic microwave integrated circuit (MMIC). According to the results, an open stub employing coplanar waveguide (OSCPW) on PES exhibited much lower loss than that on silicon substrate. The OSCPW with a length of $500{\mu}m$ on PES showed capacitance values of 0.031 ~ 0.044 pF from 0.5 to 50 GHz. For application to a relatively high-value capacitive matching, an open stub employing a fishbone-type transmission line (OSFTTL) was fabricated on PES, and its characteristics were investigated. The OSFTTL showed much higher capacitance values than the OSCPW due to the high effective permittivity value. Specifically, the OSFTTL on PES showed capacitance values of 0.066 ~ 0.24 pF from 0.5 to 50 GHz, which are higher than those for the open stub on silicon substrate. The above results indicate that the OSCPW and OSFTTL on PES can be effectively used for application to low/high-value capacitive matching components on microwave and millimeter wave flexible MMIC. To the best of the authors' knowledge, this work is the first report of the investigation of RF capacitive matching components on PES substrate.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.2
• /
• pp.139-149
• /
• 1994

In this paper, a finite element technique is applied to the prediction of the wave resonance phenomena in harbors. The mild-slope equation is used with a partial reflection boundary condition introduced to model the energy dissipating effects on the solid boundary. For an efficient modeling of the radiation condition at infinity, a new infinite element is developed. The shape function of the infinite element is derived from the asymptotic behavior of the first kind of the Hankel's function in the analytical boundary series solutions. For the computational efficiency, the system matrices of the element are constructed by performing the relevant integrations in the infinite direction analytically. Comparisons with the results from experiments and other solution methods show that the present model gives fairly good results. Numerical experiments are also carried out to determine the proper distance to the infinite elements from the mouth of the halter, which directly affect the accuracy and efficiency of the solution.

• 한국정보통신설비학회:학술대회논문집
• /
• 2008.08a
• /
• pp.469-472
• /
• 2008

In this paper, we discuss the recent trends on the passive UHF RFID tag chip design techniques and several important system parameters. We also summarize link budget studies on both conventional and modem UHF RFID communications. The paper highlights the reverse link limited case, which has known to be the minor concern if reader continuous wave (CW) can reach the tag in sufficient level. This makes sense when the tag sensitivity is rather high (over 10-12${\mu}W$); however, since the tag chip fabrication technologies have been developed by time, the tag chip threshold levels are now less-dominant in determining link margin. If the tag limitation can be alleviated, the forward link limited case can be resolved; thus, we rather focus on the path-loss problem. Since the path-losses are still exist in both forward and reverse links, and it can be doubled while CW travels the reader-tag-reader path because forward link and reverse link are on the same distance. Consider if reader receiver sensitivity is very high in the worst case. In this case, weaken tag response (i.e., backscatters) cannot reach the level that reader receiver can process tag data; bit-error rate can be higher. Overall, backscatter levels should be high enough so that reader receiver can correctly function. After discussing link budget, we carried out practical measurements on fading effects between two circularly polarized UHF RFID antennas in a small scale area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.639-642
• /
• 2005

HTS Transformer developing is developing a power distribution and transmission class HTS transformer that is one of the 21st century superconducting frontier projects. Therefore, we prepared the model, that is Z continuous winding from Kapton insulated Cu tape for a small simulated the HTS transformer. For the development of electrical insulation design of a HTS transformer with Z continuous winding, we have been discussed insulation composition and investigated breakdown characteristics such as breakdown of liquid $N_2(LN_2)$, polymer and surface flashover on FRP and breakdown-surface combination in $LN_2$. Also we have been designed and manufactured a bobbin that has spiral slot for the Z continuous winding. The Z continuous winding mini-model from Kapton film insulated Cu tape for simulated 22.9kV class HTS transformer has been constructed using 0.1 % breakdown strength obtained by Weibull distribution. The widing model was measured their insulation characteristics such as ac (50kV, 1min) and impulse (154kV, $1.2\times50{\mu}s$ full wave, 3 times) withstand test and its excellent performance was confirmed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.128-128
• /
• 2000

박막의 탄성 특성을 평가하는 방법으로 nano-indentation, Brillouin light scattering measurement, ultrasonic surface wave measurement, bulge test, vibration membrane method 등 여러 가지가 제시되어 왔다. 이러한 방법들은 필름의 두께가 일정 두께 이상이 되어야 정확한 측정이 가능한 방법으로 매우 얇은 박막에서도 탄성특성을 평가할 수 있는 freehang, bridge 방법이 제시되었으며, 이 방법은 간단한 식각 공정을 통해 매우 얇은 박막에도 적용시킬 수 있다는 장점을 가지고 있다. 본 연구에서는 아주 얇은 박막에서도 탄성특성을 평가할 수 있는 freehang 방법을 이용하여 순수한 Diamond-like carbon (DLC) 필름과 Sidl 첨가된 DLC 필름의 탄성 특성을 평가하고자 한다. 실험에서 사용한 필름은 rf-PACVD 장비를 이용하여 증착하였다. 이때 전극과 플라즈마 사이의 바이어스 음전압은 -400 Vb로 합성압력은 10mTorr로 고정하였다. 사용한 반응 가스는 벤젠(C6H6), 그리고 벤젠과 희석된 실렌(SiH4 : H2 = 10 : 90)이며, 희석된 실렌의 첨가량을 조절하여 필름 내에 일정량의 Si을 함유시켰다. 각각의 조건에서 증착시간을 조절하여 필름의 두께를 변화시켰으며, KOH(5.6mol) 용액을 이용하여 습식 식각을 함으로써 freehang을 제작하였다. 이때 식각액에 의한 DLC 필름의 손상은 관찰되지 않았다. 필름의 잔류 응력을 측정하기 위해 200$\pm$10 혹은 100$\pm$5$\mu\textrm{m}$ 두께의 얇은 (100) Si wafer를 5$\times$50 mm2의 strip 형태로 절단하여 사용하였다. 필름의 압축 잔류 응력에 의해 발생한 필름/기판 복합체의 곡률은 laser 반사법과 $\alpha$-step profiler를 이용하여 측정하였으며, 이 결과를 Brenner 등에 유도된 식을 이용하여 잔류 응력을 계산하였다. 또한 제작된 frddhang은 광학 현미경과 전자주사현미경에 의해 관찰되었다. 이렇게 제작된 freehang을 이용하여 필름이 기판에 부착되기 위해 필요한 변형률을 측정하고, 독립적으로 측정된 필름의 잔류 응력을 박막의 응력-변형률 관계식에 적용하여 biaxial elastic modulus, E/(1-v)를 구할 수 있었다. 측정 결과 필름의 잔류 응력과 biaxial elastic modulus는 필름의 두께가 감소함에 따라 감소하는 경향을 나타냈으며, 같은 두께의 필름인 경우, 식각 깊이에 따른 biaxial elastic modulus 의 변화를 통해 최적의 식각 깊이를 알 수 있었다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.723-726
• /
• 2005

The two major obstacles in the application of IPMC to flapping actuators operated in the air are solvent loss and actuation force. In this paper, solvent loss of various IPMCs made of Nafion$^{TM}$117(183$\mu$m thickness) has been experimentally investigated to find out the best combination of cation and solvent for minimal solvent loss in IPMCs and higher actuation force. For this purpose. experiments for the internal solvent loss measurement of IMPCs have been conducted for various combinations of cation and solvent. From the experiments, it was found that heavy water showed improvement in the operating time up to more than two minutes. in the tip force measurement of IPMCs, it was found that smaller and thicker IPMCs produced larger tip forces. However, the shorter IPMCs generated reduced actuation displacements and created flapping motion with decreased natural frequency. For the design of flapping device actuated by 5mm wide, 10mm long, 0.2mm thick IPMCs were used in the stacked form. Since the actuation force is a few gram-force, we stacked five IPMCs to improve actuation force. To amply the actuation force, rack-and-pin ion type hinge was used for the flapping device and insect (Cicadidae) wing was attached to the stacked IPMC actuator. In the flapping test, the device could generate flapping angle of 15$^{\circ}$ at 6Hz excitation by 2.5 voltage square wave input.

• Analytical Science and Technology
• /
• v.20 no.4
• /
• pp.289-295
• /
• 2007

A simple electric circuit of an infrared photodiode electrode (IPDE) was utilized to monitor iron using square-wave (SW) anodic stripping voltammetry (SV) and cyclic voltammetry (CV). The optimum analytical conditions were determined and were compared with those of common working electrodes. The comparison showed that CV is more sensitive and convenient to use than the common voltammetry methods. At the optimized conditions, the working ranges of 0.1- to 0.8- and 0.85- to 6.0 mg/L iron was obtained. Relative standard deviation of 15 measurements of iron (0.4 mg/L) was 0.09%. The analytical detection limit was found to be $80{\pm}0.6ug/L$, which was applied to iron in waste water.