• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.594-600
• /
• 2022

When a large liquefied natural gas (LNG) carrier is anchored at a coastal terminal, calculations on mooring forces of mooring cables induced by environmental loads such as strong winds and currents are needed to secure mooring safety. The advantages and disadvantages of several existing mooring force calculation methods are compared and analyzed with their application conditions. Resultingly, mooring equipment guidelines of the Oil Companies International Marine Forum (OCIMF) are chosen as the computational method for this study. In this paper, the mooring forces of a large LNG carrier with spectrum was calculated using the OCIMF mooring equipment guidelines. The calculation shows similar maximum forces resulted from the calculation using experiment data of a wind tunnel test. To verify the results, OPTIMOOR, a dedicated mooring force calculation software, is used to calculate the same mooring conditions. The results of both calculations show that the computational method recommended by OCIMF is safe and reliable. OPTIMOOR calculates more detailed tensile force of each mooring cable. Thus, the calculation on mooring forces of mooring cables of a large LNG carrier using OCIMF mooring equipment guidelines is verified as an applicable and safe method.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.26 no.1
• /
• pp.31-40
• /
• 1993

This paper deals with static tension analysis method for Floating Tire Breakwater(FTB). FTB can be used for the limited wave height. It is especially focused on Goodyear type FTB easily applied to the breakwater for the fisheries cultivating region. The numerical examples for FTB design procedure was reviewed. It is also studied the static analysis method of offshore catenary spread mooring system. The general calculation procedure for the tension versus excursion curves for the multi-line system using the basic catenary relationship was studied. Calculation results showed good agreement with some existing mooring results. To extend this mooring force calculating method to the floating fisheries caitivating cages, the strength of synthetic fiber was considered. This analysis method can be used to the estimation of the mooring force for the floating structures such as floating breakwaters and floating artificial reefs.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.4
• /
• pp.299-307
• /
• 2017

The design of the mooring line to maintain the position of an offshore structure in rough marine environments is recognized as a very important consideration. Conventional fatigue evaluation of a mooring line was performed by considering the tensile force acting on the mooring line, but the mooring line broke after 238 days in the girassol area even though the expected fatigue life was expected to be longer. The causes of this event are known to be due to OPB/IPB (out-of-plane bending/in-plane bending) caused by chain link friction due to the excessive tensile strength of the mooring line. In this study, three models with different boundary conditions were proposed for fatigue analysis of a mooring line considering OPB/IPB. Interlink stiffness was calculated by nonlinear structure analysis and a stress concentration factor was derived. In addition, the sensitivity of interlink stiffness according to the magnitude of tensile force, large deformation effect, and coefficient of friction was analyzed, and the effect of critical elastic slip and bending moment calculation position on interlink stiffness was confirmed.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.2
• /
• pp.119-124
• /
• 2015

The purpose of this research is a verification of the current equation for calculating equipment number and a suggesting a method for development of a rational new equation. The equation for calculating equipment number consists of total surface area of a ship that fluid resistance act on. Equipment number determines the specification of anchoring and mooring equipment such as anchor weight, anchor chains length and diameter, the number, length and breaking load of tow lines and mooring lines. The equation for equipment number calculation is basically derived considering x, y components of a wind and current force acting on a ship. But this equation is only based on a tanker, which was main type of ships when the equation was derived. Therefore, verification of the equation is required for other types of ships, such as container carrier, LNG carrier, etc. Therefore, in this research, we find out the equation for equipment number calculation should be revised for other types of ships especially the container carrier, by comparing wind and current force acting on a ship to holding force of an anchor and anchor chains, which are selected based on the equipment number.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.1 no.1
• /
• pp.102-111
• /
• 1998

Ocean monitoring facilities are divided into two types, fixed type and floating type. This paper deals with wane load calculation and mooring system for a floating monitoring facility. Wave load and drift forces are calculated for an example case of floating monitoring buoy To enlarge holding power of anchor, circular pile model test was performed. A program for horizontal force of circular pile in sand was made and the calculated result showed fairy good agreement with the result of model test. It is expected that this method will provide good estimation for the holding power of the prototype of circular pile anchor which is relied upon SCUBA activity for installation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.1 s.71
• /
• pp.105-111
• /
• 2006

Dolphin mooring system can be a good candidate for the VLFS fastening system in view point of strength and effectiveness. In the design process of the dolphin system, precise calculation of the wave forces and the subsequent selecting the proper number of the piles adopted are one of the main factors. In this paper, one of the design process of the dolphin system is investigated and a proper configuration of the system is derived based on the structural characteristics of the system that was obtained through the structural analysis of the basic pile element confronted to the external loadings including wave impact load. It was found that lot the better design of ihe mooring system for VLFS, mono pile mooring system is more recommendable in a specific condition than other multi piles mooring system.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.6
• /
• pp.423-428
• /
• 2010

This study is aiming to find one of reasonable guidelines to select a proper berthing ship at Kwang Yang harbors for loading/unloading for the POSCO(Pohang Steel Co. Ltd.). For dynamic analysis for the moored ships, the selection of subjected vessels has to be given the priority, so that the motion characteristics are figured out. The calculation of the dynamic fluid forces and wave, wind and current forces in time domain are followed. Then, the dynamic mooring analyses are performed. This study might contribute to make a new guideline by which the proper sized and loaded ships could be moored safety at the berths of Kwang Yang Harbor.

• Journal of Ocean Engineering and Technology
• /
• v.32 no.6
• /
• pp.427-432
• /
• 2018

Tidal current power is one of the energy sources of the ocean. Electricity can be generated by converting the flow energy of the current into the rotational energy of a turbine. Unlike tidal barrage, tidal current power does not require dams, which have a severe environmental impact. A floating-type tidal current power device can reduce the expensive support and installation cost, which usually account for approximately 41% of the total cost. It can also be deployed in relatively deep water using tensioned wires. The dynamic behavior of a floater and turbine force are coupled because the thrust and moment of the turbine affect the floater excursion, and the motion of the floater can affect the incoming speed of the flow into the turbine. To maximize the power generation and stabilize the system, the coupled motion of the floater and turbine must be extensively analyzed. However, unlike pile-fixed devices, there have been few studies involving the motion analysis of a moored-type tidal current power device. In this study, the commercial program OrcaFlex 10.1a was used for a time domain motion analysis. In addition, in-house code was used for an iterative calculation to solve the coupled problems. As a result, it was found that the maximum mooring load of 200 kN and the floater excursion of 5.5 m were increased by the turbine effect. The load that occurred on the mooring system satisfied the safety factor of 1.67 suggested by API. The optimum mooring system for the floating tidal current power device was suggested to maximize the power generation and stability of the floater.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.2
• /
• pp.202-209
• /
• 1998

A three-dimensional numerical method based on the Green's integral equation is developed to predict the motion response and drift force in waves for the ocean monitoring facilities. In this method, we use source and doublet distribution, and triangular and rectangular eliments. To eliminate the irregular frequency phenomenon, the method of improved integral equation is applied and the time-mean drift force is calculated by the method of direct pressure integration over the body surface. To conform the validity of the present numerical method, some calculations for the floating sphere are performed and it is shown that the present method provides sufficiently reliable results. As a calculation example for the real facilities, the motion response and the drift force of the vertical cylinder type ocean monitoring buoy with 2.6 m diameter and 3,77 m draft are calculated and discussed. The obtained results of motion response can be used to determine the shape and dimension of the buoy to reduce the motion response, and other data such as the effect of motion reduction due to a damper can be predictable through these motion calculations. Also, the calculation results of drift force can be used in the design procedure of mooring system to predict the maximum wave load acting on the mooring system. The present method has, in principle, no restriction in the application to the arbitrary shape facilities. So, this method can be a robust tool for the design, installation, and operation of various kinds of the floating-type ocean monitoring facilities.

• Ocean Systems Engineering
• /
• v.8 no.4
• /
• pp.441-459
• /
• 2018

A coupled dynamic analysis of a semisubmersible-type FOWT has been carried out in time domain under the combined action of irregular wave and turbulent wind represented respectively by JONSWAP spectrum and Kaimal spectrum. To account for the turbine-floater motion coupling in a more realistic way, the wind turbulence has been incorporated into the calculation of aerodynamic loads. The platform model was referred from the DeepCwind project and the turbine considered here was the NREL 5MW Baseline. To account for the operationality of the turbine, two different environmental conditions (operational and survival) have been considered and the aerodynamic effect of turbine-rotation on actual responses of the FOWT has been studied. Higher mean offsets in surge and pitch responses were obtained under the operational condition as compared to the survival condition. The mooring line tensions were also observed to be sensitive to the rotation of turbine due to the turbulence of wind and overestimated responses were found when the constant wind was considered in the analysis. Additionally, a special analysis case of sudden shutdown of the turbine has also been considered to study the swift modification of responses and tension in the mooring cables.