• Nuclear Engineering and Technology
• /
• 제54권3호
• /
• pp.991-996
• /
• 2022

Microstructures of monolithic high purity SiC and SiC with sintering additives after neutron irradiation to a fluence of 2.0-2.5 × 10²⁴ n/m² (E > 0.1 MeV) at 333-363 K and after post-irradiation annealing up to 1673 K were observed using a transmission electron microscopy. Results showed that no black spot defects or dislocation loops in SiC grains were found after the neutron irradiation for all of the specimens owing to the moderate fluence at low irradiation temperature. Thus, it is confirmed that these specimens were swelled mostly by the formation of point defects. Black spots and small dislocation loops were discovered only after the annealing process in PureBeta-SiC and CVD-SiC, where the swelling almost diminished. Anomalous-shaped YAG grains were found in SiC ceramics containing sintering additives. These grains contained dense black spots defects and might lose crystallinity after the neutron irradiation, while these defects may annihilate by recrystallization during annealing up to 1673 K. Amorphous grain boundary phase was also presented in this ceramic, and a large part of it was crystallized through post-irradiation annealing and could affect their recovery behavior.

• 소성∙가공
• /
• 제31권4호
• /
• pp.179-185
• /
• 2022

The influence of post-roll bonding heat treatment conditions such as temperature and time on the variation in the diffusion layer, generated at the bonding interface and the subsequent mechanical properties of the roll-bonded Ti grade 1/Al1050/Ti grade 1 sheets, was systematically investigated. The intermetallic compound (IMC) phase generated by post heat treatment conditions adopted in this study was obviously indexed as monolithic TiAl₃. Whereas the thickness of IMC layer generated by annealing at 500 ℃ was approximately 100 nm scale, it drastically increased above 1.5 ㎛ when annealed at 600 ℃. Uniaxial tensile and peel tests were then performed to compare mechanical properties. As a result, the bonding strength drastically increased above 7.9 N/mm by annealing at 600 ℃, which implies that proper annealing condition was a prerequisite, to improving interface bonding strength as well as global elongation properties for Ti/Al/Ti 3-ply sheet.

• Composites Research
• /
• 제22권3호
• /
• pp.55-59
• /
• 2009

마이크로스트림 안테나는 가볍고 부피가 작을 뿐만 아니라 집적화가 가능하고, 표면 부착력이 탁월하여 많은 통신 시스템 안테나로 응용되고 있다. 안테나의 구조는 12.5GHz의 중심주파수를 갖는 사각 패치 마이크로 스트립 안테나로 설계하였고 곡률 방향으로 패치를 확장시켜 총 4개의 패치를 배열시켰다. 양쪽의 복합재료 사이에 허니컴을 삽입한 샌드위치 구조물이 되도록 설계한 다음 충격 실험을 실시하였다. 충격실험 후 안테나 성능변화를 측정한 결과 영향을 받지 않는다는 것을 확인하였다.

• 한국군사과학기술학회지
• /
• 제26권3호
• /
• pp.205-213
• /
• 2023

An optimal design of a simple beam-shaped flexure hinge mount supporting an optical mirror is presented. An optical mirror assembly is an opto-mechanically coupled system as the optical and mechanical behaviors interact. This side-supporting mount is flexible in the radial direction and rigid for the remaining degrees of freedom to support the mirror without transferring thermal load. Through thermo-elastic, optical and eigenvalue analysis, opto-mechanical performance was predicted to establish the objective functions for optimization. The key design parameters for this flexure are the thickness and length. To find the optimal values of design parameters, response surface analysis was performed using the design of experiment based on nested FCD. Optimal design candidates were derived from the response surface analysis, and the optimal design shape was confirmed through Opto-mechanical performance validation analysis.

• 대한한의진단학회지
• /
• 제24권1호
• /
• pp.1-13
• /
• 2020

Objectives Mibyeong is an ideological concept that means the state between the healthy and diseased conditions. The purpose of this study was to suggest a research direction to establish the diagnostic criteria for the Mibyeong by reviewing the research results for the Mibyeong. Methods Academic databases (OASIS for Korean database, Embase for English database, and CNKI for Chinese database) were used to search related literatures, and articles describing the concept or diagnostic criteria of the disease were selected. Results The concept of Mibyeong consisted of three different conditions: (1) subjective symptoms without a specific disease, (2) abnormal examination findings without a specific disease, and (3) a state in between health and disease. No matter which of the three conditions is applied, the spectrum of condition was very wide and diverse. Conclusions It is impossible to apply appropriate and monolithic diagnostic criteria to all types of Mibyeong. Therefore, we suggests that the Mibyeong be classified into several subtypes and the diagnostic criteria suitable for each type be established.

• 천문학회보
• /
• 제46권2호
• /
• pp.79.4-80
• /
• 2021

Sunspots' subsurface structure is an important subject to explain their stability and energy transport. Previous studies suggested two models for the subsurface structure of sunspots: monolithic model and cluster model. However, it is not revealed which model is more plausible so far. We obtain clues about the subsurface structure of sunspots by analyzing the motion of umbral flashes observed by the IRIS Mg II 2796Å slit-jaw images (SJI). The umbral flashes are believed as shock phenomena developed from upward propagating slow magnetohydrodynamic (MHD) waves. If the MHD waves are generated by convective motion below sunspots, the apparent origin of the umbral flashes known as oscillation center will indicate the horizontal position of convection cells. Thus, the distribution of the oscillation centers is useful to investigate the subsurface structure of sunspots. We analyze the spatial distribution of oscillation centers in the merged sunspot. As a result, we found that the oscillation centers distributed over the whole umbra regardless of the convergent interface between two merged sunspots. It implies that the subsurface structure of the sunspot is not much different from the convergent interface, and supports that many field-free gaps may exist below the umbra as the cluster model expected. For more concrete results, we should confirm that the oscillation centers determined by the umbral flashes accurately reflect the position of wave sources.

• 한국전기전자재료학회논문지
• /
• 제37권1호
• /
• pp.26-35
• /
• 2024

Aluminum-induced crystallization (AIC) as a route to reduce the fabrication cost and to obtain polycrystalline Si (p-Si) thin-film of large grain size is a promising alternative of single-crystalline (s-Si) substrate or p-Si thin-film obtained by conventional methods such as solid phase crystallization (SPC) and laser-induced crystallization (LIC). As the AIC process occurs at the interface between a-Si and Al thin-films, there are various process and interface parameters. Also, it directly means that there is a certain parametric window to obtain p-Si of large grain size having uniform crystal orientation. In this article, we investigate the effect of the various process and interface parameters to obtain p-Si of large grain size and uniform crystal orientation from the literature review. We also suggest the potential use of the p-Si as a virtual substrate for the growth of various compound semiconductors in a form of low-dimension as well as thin-film as a way for their monolithic integration on Si.

• 한국IT서비스학회지
• /
• 제23권1호
• /
• pp.27-35
• /
• 2024

In accordance with the cloud conversion of public sector information systems and the implementation of cloud native introduction policies, review items were presented to review the cloud native of information systems for stable and efficient cloud native deployment. By presenting cloud native considerations when promoting a project, we propose a plan to flexibly respond to policy and business changes and improve development quality and productivity to operate cloud services stably. In order for information project managers to switch to a cloud-native-based information system in order to efficiently utilize the cloud as a cloud, they must decide whether to introduce cloud-native through suitability review questions and sufficiently review development and operation costs and efficiency to promote the project. As a result of conducting a focus group interview (FGI) with a council of cloud native experts, there was an opinion that information systems can be operated in a cloud-native manner even with a monolithic structure. By fully considering the circumstances of each system, development quality and productivity, we expect to be able to operate improved to provide a stable cloud service.

• ETRI Journal
• /
• 제46권2호
• /
• pp.323-332
• /
• 2024

Receiver and transmitter monolithic microwave integrated circuit (MMIC) multifunction chips (MFCs) for active phased-array antennas for Ka-band satellite communication (SATCOM) terminals have been designed and fabricated using a 0.15-㎛ GaAs pseudomorphic high-electron mobility transistor (pHEMT) process. The MFCs consist of four-channel radio frequency (RF) paths and a 4:1 combiner. Each channel provides several functions such as signal amplification, 6-bit phase shifting, and 5-bit attenuation with a 44-bit serial-to-parallel converter (SPC). RF pads are implemented on the bottom side of the chip to remove the parasitic inductance induced by wire bonding. The area of the fabricated chips is 5.2 mm × 4.2 mm. The receiver chip exhibits a gain of 18 dB and a noise figure of 2.0 dB over a frequency range from 17 GHz to 21 GHz with a low direct current (DC) power of 0.36 W. The transmitter chip provides a gain of 20 dB and a 1-dB gain compression point (P1dB) of 18.4 dBm over a frequency range from 28 GHz to 31 GHz with a low DC power of 0.85 W. The P1dB can be increased to 20.6 dBm at a higher bias of +4.5 V.

• Nuclear Engineering and Technology
• /
• 제56권3호
• /
• pp.846-854
• /
• 2024

FEMAXI-ATF is being developed for fuel performance modeling of SiC cladded UO2 fuel with focuses on modeling pellet-cladding mechanical interactions (PCMI). The code considers probability distributions of mechanical strengths of monolithic SiC (mSiC) and SiC fiber reinforced SiC matrix composite (SiC/SiC), while it models pseudo-ductility of SiC/SiC and propagation of cladding failures across the wall thickness direction in deterministic manner without explicitly modeling cracks based on finite element method in one-dimensional geometry. Some hypothetical BWR power ramp conditions were used to test sensitivities of different model parameters on the analyzed PCMI behavior. The results showed that propagation of the cladding failure could be modeled by appropriately reducing modulus of elasticities of the failed wall element, so that the mechanical load of the failed element could be re-distributed to other intact elements. The probability threshold for determination of the wall element failure did not have large influence on the predicted power at failure when the threshold was varied between 25 % and 75 %. The current study is still limited with respect to mechanistic modeling of SiC failure as it only models the propagation of the cladding wall element failure across the homogeneous continuum wall without considering generations and propagations of cracks.