• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.5-5
• /
• 2000

In the severe accident case like LOCA, Zircaloy(Zry) claddings are oxidized not only in high temperature but also in high pressures. It is a concem whether the safety of high bum up fuels can be maintained during severe accident. The effects of steam pressure on Zry-4 oxidation, and the effect of prc-existing oxide layer on the cladding in the high temperature-high pressure oxidation of Ziy-4 were investigated. The experimental temperature range was $700-900^{\circ}C$, and the pressures were between 0.1 and l5.0MPa. Partial pressure of steam tumed out to be the important one rather than total gas pressure. The higher the steam pressure was applied, the thicker the oxide became. nle effect of st,earn pressure on the oxidation of claddings with preexisting oxide was about 40-60% less effective than that of pickled cladding. Aocelerated oxidation in highpressure slean1 seems to be originated from the formation of microcracks produced during the transformation of tetragonal zirconia to monoclinic phase. Steam pressure seems to affect the stability of tetragonal phase.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.1059-1065
• /
• 1993

The sliding wear behavior of the plasma sprayed zirconia containing 8wt% yttria was investigated over a range of room temperature to 800℃. Both of the friction coefficient and the wear loss increased reaching its maximum at about to 499℃. and then decreased again with increasing temperature up to 800℃. The worn surface at elevated temperature were observed and analyzed by scanning electron microscopy and X-ray diffractometer to study the mechanisms of high temperature wear behavior. Surface morphology of the worn samples changes with temperature. Monoclinic (m)/tetragonal (t) x-ray peak intensity ratio of wear debris and worn surface decreased with increasing temperature. Non-transformable tetragonal (t') to metastable tetragonal (t) phase transformation of worn surface increased with increasing temperature. The results indicate that dehumidification and above phase changes are contributing to the high temperature wear behavior of the plasma sprayed ZrO2-Y2O3 coatings.

• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.119-126
• /
• 1992

3 mol% Y2O3-doped ZrO2 powders were prepared by hydrolysis with 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 mol/ιH2O/ethanol into 0.1 mol/ι zirconium and yttrium alkoside/ethanol. Spherical monodispersed yttria-partially stabilized zirconia particles with an average diameter of about 0.5 ${\mu}{\textrm}{m}$ were prepared by hydrolysis with 0.2 mol/ιH2O/ethanol. The as-prepared powder was amorphous and with heating it transformed into cubic up to 80$0^{\circ}C$ and into tetragonal over 100$0^{\circ}C$. 3 mol% Y2O3-doped ZrO2 powders calcined over and up to 80$0^{\circ}C$ were a mixture of tetragonal and monoclinic and only tetragonal as determined by X-ray diffraction, respectively.

• 대한전자공학회논문지TE
• /
• 제39권1호
• /
• pp.1-8
• /
• 2002

단사정 ZrO/sub 2/(ZrO2(m)) 또는 Y/sub 2/O/sub 3/를 5.35wt% 첨가한 정방정 ZrO2(ZrO/sub 2/(t))를 A1/sub 2/O/sub 3/에 첨가하여 물리적 및 전기전도도의 영향을 연구하였다. ZrO/sub 2/(m)과 ZrO/sub 2/(t)의 첨가는 A1/sub 2/O/sub 3/의 소결밀도를 증가 시켰다. ZrO2(t)의 첨가함에 따라 비커스 경도 또한 증가했으며, 그 량이 20wt%에서 최대가 되었다. 시편의 경도는 소결밀도에 의존함을 알 수 있었다. A1/sub 2/O/sub 3/-ZrO/sub 2/계의 경도는 ZrO/sub 2/(t)의 첨가에 의해 개선 되었고, ZrO/sub 2/(m)의 첨가가 ZrO/sub 2/(t)의 첨가보다 A1/sub 2/O/sub 3/-ZrO/sub 2/계의 열충격 특성에는 더 많은 영향을 받음을 알 수 있었다. l5wt% 이상의 ZrO/sub 2/(t) 첨가에서 인가전압이 증가 함에 따라 점차로 전기전도도가 증가 하였으나, ZrO/sub 2/(m)의 첨가에서는 영향이 없었다.

• 한국세라믹학회지
• /
• 제24권3호
• /
• pp.243-250
• /
• 1987

9mol% 의 MgO로 $1650^{\circ}C$에서 4시간 고상반응과 동시에 소결시킨 부분안정화 지르코니아 소결체(9MZ-PSZ)를 소성후 냉각중 $1200^{\circ}C$~$1400^{\circ}C$의 온도범위에서 열처리하여 이의 열분해 반응, 열충격기등 및 기전력 특성에 대하여 조사하였다. 열충격시럼 전과 후의 강도, 열팽창률, X-선 회절분석에 의한 단사정사 함률과 상전이, 밀도 및 갈바닉 전위를 측정하였으며 SEm에 의한 미세구조를 관찰하였다. 입체부근의 미소화학분석은 $1350^{\circ}C$ 열처리 시편에 한하여 EDX 로 정량하였다. 9MZ-PSZ 시편의 열처리에 의하여 입방정상의 $ZrO^{2}$는 상기 온도범위에서는 준안정-정방정상의 $ZrO^{2}$와 MgO로 열분해되는데, 이때 생성된 준안정 정방정상은 열충격 시험후의 잔류강도를 응력유기상전이 효과에 의해 증가시킨다. 또한 MgO는 입계에 연속적으로 존재하는데 이런하 MgO의 연속상을 통한 열전도롤 인하여 PSZ의 열충격 저항이 크게 향상된다. 이때 PSZ의 열분해 속도와 단사정상 함량은 열처리 온도가 $1400^{\circ}C$에서 $1200^{\circ}C$로 감소됨에 따라 증가한다. 갈바닉전의 측정결과 이상의 열처리에 의하여도 양호한 기전력 특성을 갖는 지르코니아 고체전해질을 제조할 수 있다.

• Bulletin of the Korean Chemical Society
• /
• 제26권5호
• /
• pp.755-762
• /
• 2005

A series of catalysts, NiO/$CeO_2-ZrO_2/WO_3$, for ethylene dimerization was prepared by the precipitation and impregnation methods. For NiO/$CeO_2-ZrO_2/WO_3$ sample, no diffraction line of nickel oxide was observed up to 40 wt%, indicating good dispersion of nickel oxide on the surface of catalyst. The hexagonal and monoclinic phases of $WO_3$ up to the calcination temperature of 500 ${^{\circ}C}$ were observed, whereas the hexagonal phase of WO3 completely was transformed into monoclinic phase of $WO_3$ at 600 ${^{\circ}C}$ and above. The role of $CeO_2$ in the catalysts was to form a thermally stable solid solution with zirconia and consequently to give high surface area and acidity. The catalytic activities for ethylene dimerization were correlated with the acidity of catalysts measured by the ammonia chemisorption method. 25-NiO/5-$CeO_2-ZrO_2/15-WO_3$ containing 25 wt% NiO, 15 wt% $WO_3$ and 5 mol% $CeO_2$, and calcined at 400 ${^{\circ}C}$ exhibited a maximum catalytic activity due to the effects of $WO_3$ modifying and $CeO_2$ doping.

• 한국표면공학회지
• /
• 제55권6호
• /
• pp.368-375
• /
• 2022

YSZ (Yttria Stabilized Zirconia) is used as a thermal barrier coating material for gas turbines due to its low thermal conductivity and high fracture toughness. However, the operating temperature of the gas turbine is rising according to the market demand, and the problem that the coating layer of YSZ is peeled off due to the volume change due to the phase transformation at a high temperature of 1400℃ or higher is emerging. To solve this problem, various studies have been carried out to have phase stability, low thermal conductivity, and high fracture toughness in a high temperature environment of 1400℃ or higher by doping trivalent and tetravalent oxides to YSZ. In this study, the monoclinic phase formation behavior and crystallinity were comparatively analyzed according to the total doping amount of oxides by controlling the doping amounts of Sc₂O₃ and Gd₂O₃, which are trivalent oxides, and TiO₂, which are tetravalent oxides, in YSZ. Through comparative analysis of monoclinic phase formation and crystallinity, the thermal conductivity of the thermal barrier coating layer according to the amount of doping was predicted.

• 한국세라믹학회지
• /
• 제54권4호
• /
• pp.285-291
• /
• 2017

This study investigated the effects of grain size and phase constitution on the mechanical properties of $3Y-ZrO_2$ by varying the sintering conditions. The raw powder prepared by a low-cost wet milling using the coarse solid oxide powders was sintered by both pressureless sintering and hot-pressing, respectively. As increasing holding time at $1450^{\circ}C$ for pressureless sintering, it promoted the microstructural coarsening of matrix grains and the phase transformation to tetragonal phase, whereas the bimodal microstructure embedded with abnormal $cubic-ZrO_2$ grains was observed regardless of sintering time. On the other hand, the specimens hot-pressed at $1300^{\circ}C$ for 2 h reached ~ 97% of relative density with homogeneous fine microstructure and mixed phase constitution. It was found that the proportion of untransformed monoclinic zirconia had the most adverse effect on the biaxial strength compared to the impacts of grain size and density. The pressureless sintering of the low-cost powder for prolonged sintering time to 8 h led to a decent combination of mechanical properties ($H_V=13.2GPa$, $K_{IC}=8.16MPa{\cdot}m^{1/2}$, ${\sigma}=981MPa$).

• 한국세라믹학회지
• /
• 제41권1호
• /
• pp.69-75
• /
• 2004

인공치아용 3Y-TZP와 (Y,Nb)-TZP/$Al_2O_3$ 복합체를 유사 구강분위기인 인공타액 하에서 500-3000N의 하중 조건으로 $10^6$ 횟수까지 헤르찌안 반복하중 피로특성을 조사하였다. 500N의 하중에서 $5{\times}10^5$까지 반복피로 실험결과, 강도 저하 및 균열 현상은 관찰되지 않았다. 피로특성은 SY-TZP가 (T,Nb)-TZP/$Al_2O_3$ 복합체보다 상전이에 의한 응역회복 때문에 우수하였다. 하중값이 증가함에 따라 링 균열에서 방사상 균열로 전이되었을 때 급격한 강도 저하 현상이 발생하였다. 강도 저하 현상은 유사 구강 분위기하에서 반복 하중 접촉 시 발생한 균열을 통해 침투한 인공타액의 화학적 침식으로 더욱 가속화 되었다.

• Restorative Dentistry and Endodontics
• /
• 제46권4호
• /
• pp.54.1-54.10
• /
• 2021

Objectives: The purpose of this study was to quantify phase transformation after hydrofluoric acid (HF) etching at various concentrations on the surface of yttria-stabilized tetragonal zirconia polycrystal (Y-TZP), and to evaluate changes in bonding strength before and after thermal cycling. Materials and Methods: A group whose Y-TZP surface was treated with tribochemical silica abrasion (TS) was used as the control. Y-TZP specimens from each experimental group were etched with 5%, 10%, 20%, and 40% HF solutions at room temperature for 10 minutes. First, to quantify the phase transformation, Y-TZP specimens (n = 5) treated with TS, 5%, 10%, 20% and 40% HF solutions were subjected to X-ray diffraction. Second, to evaluate the change in bond strength before and after thermal cycling, zirconia primer and MDP-containing resin cement were sequentially applied to the Y-TZP specimen. After 5,000 thermal cycles for half of the Y-TZP specimens, shear bond strength was measured for all experimental groups (n = 10). Results: The monoclinic phase content in the 40% HF-treated group was higher than that of the 5%, 10%, and 20% HF-treated groups, but lower than that of TS-treated group (p < 0.05). The 40% HF-treated group showed significantly higher bonding strength than the TS, 5%, and 10% HF-treated groups, even after thermal cycling (p < 0.05). Conclusions: Through this experiment, the group treated with SiO₂ containing air-borne abrasion on the Y-TZP surface showed higher phase transformation and higher reduction in bonding strength after thermal cycling compared to the group treated with high concentration HF.