• 한국수소및신에너지학회논문집
• /
• 제29권3호
• /
• pp.267-273
• /
• 2018

From the experiments of various temperature and gas compositions, total resistance which is composed of ohmic resistance, anode resistance, cathode resistance and Nernst loss was calculated wit simple assumption. In this work, the anode and the cathode resistance was modelled with new equation which can account for the correlation between the operating temperature and the gas composition. The proposed model can predict the resistance with maximum error of 2.57% and employed in the simulation of molten carbonate fuel cells.

• Journal of Electrochemical Science and Technology
• /
• 제1권2호
• /
• pp.102-111
• /
• 2010

Molten carbonate fuel cell (MCFC) power plants are one of most attractive electricity generation systems for the use of biogas to generate high-efficiency ultra-clean power. However, MCFCs are considerably more expensive than comparable conventional electricity generation systems. The commercialization of MCFCs has been delayed more than expected. After being effective in the Kyoto protocol and considerably increasing the fossil price, the attention focused on $CO_2$ regression and renewable energy sources has increased dramatically. In particular, the commercialization and application of MCFC systems fed with biogas have been revived because of the characteristics of $CO_2$ collection and fuel variety of MCFCs. Better economic results of MCFC systems fed with biogas are expected because biogas is a relatively inexpensive fuel compared to liquefied natural gas (LNG). However, the pretreatment cost is added when using anaerobic digester gas (ADG), one of the biogases, as a fuel of MCFC systems because it contains high $H_2S$ and other contaminants, which are harmful sources to the MCFC stack in ADG. Thus, an accurate economic analysis and comparison between MCFCs fed with biogas and LNG are very necessary before the installation of an MCFC system fed with biogas in a plant. In this paper, the economic analysis of an MCFC fed with ADG was carried out for various conditions of electricity and fuel price and compared with the case of an MCFC fed with LNG.

• 한국수소및신에너지학회논문집
• /
• 제22권5호
• /
• pp.599-608
• /
• 2011

The Ni-Al anodes of the molten carbonate fuel cell (MCFC) with three different structures were successfully fabricated in order to reduce the thickness of the anode down to 0.3 mm; one was the non-supported anode made by a conventional tape casting method, and others were the supported anodes made by lamination or direct casting on the nickel screen. It was seen from the physical analyses and cell operation that the supported thin anodes made by direct casting showed good mechanical strength and cell performance because of a good contact between the anode materials and the support. The single cell using the above anode showed the cell voltage of 0.858 V at the current density of 150$mA/cm^2$ with the nitrogen cross-over of only 0.6% at the operation time of 1,000 h, which was similar to the performance of the conventional thick (0.7 mm) anode. The ability to utilize a thin configuration of anode should cut down the amount of nickel alloy and consequently reduce its manufacturing cost.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.283-288
• /
• 2014

PdO-doped $BaZr_{0.85}Y_{0.15}O_{3-\delta}$ (BZPY) proton conductors have been proposed as applicable for intermediate temperature electrolytes for protonic ceramic fuel cells (PCFCs) because the PdO doping is effective for improving the proton conductivity of $BaZr_{0.85}Y_{0.15}O_{3-\delta}$ (BZY) with high affinity for hydrogen. In order to further improve the conductivity of BZPY, two-phase composite electrolytes consisting of a BZPY and molten carbonate were designed. Dense BZPY-based composite electrolytes were fabricated after sintering at $670^{\circ}C$ for 4 h, since molten carbonates fill the grain boundary of the porous BZPY matrix. Furthermore, BZPY/$(Li-0.5Na)_2CO_3$ composites show a significantly enhanced protonic conductivity at intermediate temperatures. This may be because easy proton transport is possible through the interface of the carbonate and oxide phase.

• 한국수소및신에너지학회논문집
• /
• 제16권2호
• /
• pp.170-179
• /
• 2005

Electrolyte loss is considered as one of the major obstacles limiting the life time of molten carbonate fuel cells (MCFCs). Unit cells with an effective area of 100 $cm^2$ were prepared and were operated to determine the optimum matrix thickness which contains the maximum amount of electrolyte without serious preformance loss caused by high resistance. Matrices with different thickness, 1.45, 1.8, and 2.3 mm, were used in unit cells and those cells were operared about 5000, 10000, and 4000 hrs. The unit cell used 1.8 mm thick matrix showed 0.85 V (at 150 mA/$cm^2$) as the intial performance and this cell voltage is not lower than the cell voltage obtained in the cell with 1 mm thick matrix. This cell was operated for 10000 hrs. The cell used 1.45 mm thick matrices showed 16.6 % in the electrolyte loss after 5000 hr operation. In the case of the cell with 2.3 mm thick matrix, the initial cell voltage was below 0.80 V (at 150 mA/$cm^2$). For thermal cycle test, the gas crossover amount of unit cell used 1.8 mm thick matrix was much less than that of the cell with 1.0 mm thick matrix.

• 한국산학기술학회논문지
• /
• 제12권7호
• /
• pp.2939-2944
• /
• 2011

용융탄산염형 연료전지 시스템의 성능 향상을 위해 핵심 부분인 스택을 수치적으로 모사할 필요성이 대두되고 있다. 스택은 다양한 재질, 즉 금속, 세라믹, 폴리머 등으로 이루어져 있고 또한 단위전지 수백 장이 적층되어 제작되기 때문에 이를 전부 세세히 모델링하여 고려하는 것은 거의 불가능하다. 이에 따라 스택 전체를 하나의 균질한 물질로 대체할 수 있는 균질 물성치 도출이 요구되고 있다. 본 논문에서는 단위전지 압축률을 도입하고 모든 압축 변형이 분리판과 매트릭스에서만 일어난다는 등의 몇 가지 기본 가정 하에서 스택의 두 가지 영역, 즉 활성 영역과 매니폴드 영역에서 각각 균질 물성치를 추정하였다. 추정된 물성치를 실제 문제에 적용하여 성공적인 결과를 얻을 수 있었다.

• 기술사
• /
• 제44권1호
• /
• pp.48-52
• /
• 2011

The KEPCO Research Institute has developed Molten Carbonate Fuel Cell(MCFC) since 1993. Recently, an 125-kW MCFC system was operated at Boryeong thermal power plant, Korea from December, 2009 to March, 2010, This system is composed of an 125-kW stack, mechanical balance of plant (MBOP), and Power Conditioning System. The stack has 200 unit cells of which effective area is 10,000 cm2. Especially, MBOP is mainly made up of ejector and catalytic combustor which help this system to be supplied with cathode inlet gas using anode tail gas and fresh air. After the pretreatment of this system was performed for about 20 days, initial load operation was performed at January. 2010. Moreover, this system had been operated for 3,270 hours.

• 전기화학회지
• /
• 제13권1호
• /
• pp.34-39
• /
• 2010

본 연구에서는 용융탄산염형 연료전지의 연료극 전극두께가 과전압에 미치는 영향을 $100\;cm^2$ 급 단위전지를 사용하여 검토하였다. 용융탄산염형 연료전지에서의 수소 산화속도는 충분히 빨라 전극면적이 성능에 크게 영향을 미치지 않을 수 있어, 본 연구에서는 전극의 기하학적 면적의 크기가 과 전압에 미치는 영향에 대해 연구하였다. 평가는 정상분극법과 비활성가스 계단형 첨가법 (ISA)와 반응물 첨가법 (RA)를 사용하여 연료극 두께 0.77 mm와 0.36 mm에 대해 수행하였다. 평가결과 두 전지에서 연료극 과전압이 거의 동일하게 관찰되어 연료극 두께에 의한 과전압의 차이는 발생하지 않았다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.353-356
• /
• 2009

A pivotal mechanical balance of plant for 75kW class molten carbonate fuel cells comprise of a catalytic burner and an ejector which has been designed and tested in KEPRI(Korea Electric Power Research Institute). The catalytic burner, which oxidizes residual fuel in the anode tail gas, was operated at several conditions. Some problems arose due to local overheating or auto-ignition, which could limit the catalyst life. The catalytic burner was designed by considering both gas mixing and gas velocity. Test results showed that the temperature distribution is very uniform. In addition, an ejector is a fluid machinery to be utilized for mixing fluids, maintaining vacuum, and transporting them. The ejector is placed at mixing point between the anode off gas and the cathode off gas or the fresh air Several ejectors were designed and tested to form a suction on the fuel tail gas and balance the differential pressures between anode and cathode over a range of operating conditions. The tests showed that the design of the nozzle and throat played an important role in balancing the anode tail and cathode inlet gas pressures. The 75kW MCFC system built in our ejector and catalytic burner was successfully operated from Novembe, 2008 to April, 2009. It recorded the voltage of 104V at the current of 754A and reached the maximum generating power of 78.5kW DC. The results for both stand-alone and integration into another balance of plant are discussed.

• 전기화학회지
• /
• 제13권3호
• /
• pp.203-210
• /
• 2010

용융탄산염 연료전지(MCFC)의 양극으로 사용되는 NiO는 $650^{\circ}C$의 용융탄산염과 산소 분위기 조건에서 안정하고 높은 전기 전도도를 가지는 장점이 있다. 그러나, 장시간 운전 시 양극에서 전해질로의 Ni dissolution은 전지 내부의 단락을 초래하여 전지의 수명을 단축시킨다. 본 연구에서는 대체 전극물질로서 코발트와 나이오븀을 코팅시킨 NiO 전극을 제조하였으며, 이렇게 제조된 전극은 기존 NiO전극과 비교하여 낮은 Ni dissolution과 안정되고 우수한 전기화학 성능을 보임을 확인하였다.