• Design & Manufacturing
• /
• 제2권6호
• /
• pp.7-10
• /
• 2008

Injection-stretch blowing system for preform has been developed in this study. The preforms for injection blow molding and injection stretch blow molding are being manufactured by injection molding. However it contains gate mark that affects the bottom crack in the PET bottle. The compression molded preform does not contain gate mark, thus the appearance quality of bottle has been increased and the residual stress near gate(bottom of the bottle) has been reduced. The thickness distributions, haze, and transmittance are well accepted for the preform. Also, flow characteristics of the resin between a core and cavity could be analyzed through computer simulation.

• Design & Manufacturing
• /
• 제6권2호
• /
• pp.1-5
• /
• 2012

Weld line in injection molded part is one of the defects in injection molding process. Weld line deteriorates not only appearance quality but mechanical property. In this study, ABS and PP were used as experimental materials. And weld line length, depth and strength have been examined according to the injection molding conditions. As the results of experimental studies, weld line length increased as flow rate increases for all materials. And the flow rate is most influenced to the creation of weld line length. Also weld line strength increased, as flow rate and melt temperature increase for all materials. The whole experiment results was similar to CAE analysis results.

• 소성∙가공
• /
• 제22권1호
• /
• pp.48-53
• /
• 2013

As the adoption of injection molding technology increases, injected-molded optical products require higher dimensional accuracy and optical stability than ever before. In the present study, four kinds of molding methods, i.e., conventional injection molding (CIM), injection/compression molding (ICM), rapid heat and cooling the mold(RHCM) and rapid injection/compression molding (RICM) were selected in order to investigate the optical anisotropy of a 7 inch Light Guide Plate(LGP) by examining the gap-wise distribution of birefringence and the extinction angle. The results indicate that the compression process can decrease flow-induced birefringence over the whole region and that rapid heating can decrease the birefringence level better than conventional molding. In addition, for the combination of compression and rapid heating a reversal flow was detected from the distribution of the extinction angle near the gate.

• Design & Manufacturing
• /
• 제11권1호
• /
• pp.14-18
• /
• 2017

Recently, the injection-molded products are lighter, and thinner than ever. In this work, Injection molding simulation was conducted to analysis the filling pattern imbalance in high speed injection molding process for thin-wall injection component, 8 inches LGP. Numerical analysis shows that shear heated polymer near the side wall causes filling imbalance between center and side of cavity. Short shot experiments were conducted and compared with simulation results. Filling imbalance ratio showed a tendency to increase for wider fan gate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.723-726
• /
• 2001

The design of delivery system is one of the most important subject in injection molding. Delivery system is a channel to flow the polymer melt from the injection molding machine to the mold cavities and affect quality and productivity of the part. The synthesis of delivery system of injection molding has been done empirically, since it requires profound knowledge about the moldability and causal effects on the properties of the part, which are not available to designers through the current CAD systems. A knowledge-based CAD system is constructed by adding the knowledge module to an existing geometric modeler and contains knowledge to permit non-experts ad well as mold design experts to generate the acceptable geometries of gate and runner for injection molded parts.

• 소성∙가공
• /
• 제16권1호
• /
• pp.54-60
• /
• 2007

Optimum injection molding condition for a box mold was searched by the Response Surface Analysis(RSA) with the aid of process monitoring system(PMS). Process variables on the control panel of the injection molding machine such as barrel temperatures, screw speed profile, holding pressures, etc. cannot guarantee the uniformity of the material variables directly related with the state of the product in the mold cavity. In order to make sure the state of the resin in the cavity, pressures and temperatures in the cavity, runner and nozzle were monitored in the experiment with the PMS. To accomplish the consistency of the molding process, dependent variables such as the switchover point and holding time were searched with the PMS. With a proper objective function about deflection of the box-type product, the optimum injection molding condition was obtained.

• 한국정밀공학회지
• /
• 제25권4호
• /
• pp.47-52
• /
• 2008

Recently, the study for filling imbalance in thermoplastic polymer has gradually been increased. However, it is hard to find the researches for filling imbalance of thermoplastic elastomer(TPE). The experiment of filling imbalance was conducted for the three kinds of thermoplastic vulcanizes(TPVs) and PP polymer in the mold with geometrically balanced runner system(Unary Branch Type Runner System). In this experiment, the effects of the melt temperature, injection pressure and injection speed on the filling imbalance were investigated. There was also the imbalance in TPV injection molding process as well as in conventional injection molding with plastics. The tendency of filling imbalance in TPV injection molding specially decreased by taking place the hesitation of TPV melt.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.259-264
• /
• 2005

The shrinkage of the product in injection molded part occurs due to the volume change with variation of temperature and pressure and is influenced by the processing conditions of injection molding. Mold designers greatly concerns the shrinkage of parts for a high dimensional accuracy. In this study, bar type HIPS specimen with 15x19 grid on the surface was tested. The amount of shrinkage of flow and transverse directions was examined with respect to the injection molding conditions such as melt temperature, injection speed, holding pressure, mold temperature and cooling time. As the packing pressure increased, the difference of shrinkage of both directions is decreased and the absolute shrinkage value also decreased.

• 소성∙가공
• /
• 제11권8호
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.109-114
• /
• 2005

The large injection molded parts technology such as instrument panel, front and rear bumper are presented for a precision molding. Some lead time and cost are required to product these part from design to mass product. Recently, CAE is widely used in product design, mold design and analysis of molding conditions to reduce time and cost. The optimal molding conditions can be obtained by DOE(Design of Experiment). The optimal design applications with CAE and DOE have been used in small molded parts. However, application to the large molded body is not reported. In this paper, optimization of injection molding process is studied for quality control in mass production of automobile bumper. Mold temperature difference is chosen through robust design of injection molding process, the molding process being optimized in term of shrinkage and deflection. The optimal conditions through DOE are validated by using injection molding analysis.