• Design & Manufacturing
• /
• 제14권3호
• /
• pp.8-16
• /
• 2020

In this study, the vibration signal of the mold was measured and analyzed to monitoring the process time and characteristics during injection molding. A 5 inch light guide plate mold was used to injection molding and the vibration signal was measured by MPU6050 acceleration sensor module attached the surface of fixed mold base. Conditions except for injection speed and packing pressure were set to the same value and the change of the vibration signal of the mold according to injection speed and packing pressure was analyzed. As a result, the vibration signal had a large change at three points: "Injection start", "V/P switchover", and "Packing end". The time difference between "injection start" and "V/P switchover" means the injection time in the injection molding process, and the time difference between "V/P switchover" and "Packing end" means the packing time. When the injection time and packing time obtained from the vibration signal of the mold are compared with the time recorded in the injection molding machine, the error of the injection time was 2.19±0.69% and the error of the packing time was 1.39±0.83%, which was the same level as the actual value. Additionally, the amplitude at the time of "injection start" increased as the injection speed increased. In "V/P switchover", the amplitude tended to be proportional to the pressure difference between the maximum injection pressure and the packing pressure and the amplitude at the "packing end" tended to the pressure difference between the packing pressure and the back pressure. Therefore, based on the result of this study, the injection time and packing time of each cycle can be monitored by measuring the vibration signal of the mold. Also, it was confirmed that the level and trend of process variables such as the injection speed, maximum injection pressure, and packing pressure can be evaluated as the change of the mold vibration during injection molding.

• 한국산학기술학회논문지
• /
• 제16권11호
• /
• pp.7729-7735
• /
• 2015

플라스틱 사출성형제품은 금형을 제작하여 대량생산에 적합한 시스템으로서 두께가 두꺼운 자동차 핸들제품은 가스사출성형을 수행하는 것이 바람직하다. 가스사출성형은 용융된 원재료를 금형내로 충전시킨 후 질소가스를 주입하는 기술이다. 가스사출성형은 재료비절감, 품질향상 등 많은 장점을 가지고 있다. Moldflow소프트웨어를 활용하여 사출성형 공정을 해석하여 제품의 휨 변형을 최소하기 위한 게이트의 위치를 결정하였으며, 기존의 일반적인 PP재료로 가스사출 성형을 했을 경우 변형이 크게 발생되므로 미네랄이18% 함유된 PP 재료로 변경하여 사출제품의 휨 변형을 최소로 하는 것과 게이트의 위치를 변경하여 핑거링현상이 발생하는 트러블을 제거하는 것을 목적으로 하였다, 또한 가스 사출성형을 수행하였을 경우 원재료가 유입되고 난후 게이트를 기준으로 가스가 유입된 형상을 파악하기 위해 비교분석해 보았다. 본 연구를 통해 제품형상에 따른 두께의 변화와 가스사출성형을 수행하더라도 플라스틱의 재료에 따라 제품의 휨이 발생 될 수 있다는 것과 게이트의 위치가 제품의 트러블에 영향을 미친다는 것을 알 수 있었다.

• 소성∙가공
• /
• 제11권8호
• /
• pp.641-650
• /
• 2002

For the production of complicated plastic parts in a cycle, a mold is needed.. The basic tasks of a mold are accommodation and distribution of the resin, shaping and cooling the melt and ejection of the molding. To achieve these goal a mold has several important parts and we classified types of molds. The 6 different major functions of a mold are explained and several types of molds are shown in her. I hope these explanation will help to understand injection molds for a design engineer.

• Design & Manufacturing
• /
• 제15권1호
• /
• pp.66-71
• /
• 2021

In this study, die turning injection(DTI) mold design for manufacturing reservoir fluid tanks used for cooling in-vehicle batteries, inverters, and motors was conducted based on multi-field CAE. Part design, performance evaluation, and mold design of the reservoir fluid tank was performed. The frequency response characteristics through modal and harmonic response analysis to satisfy the automotive performance test items for the designed part were examined. Analysis of re-melting characteristics and structural analysis of the driving part for designing the rotating die of the DTI mold were performed. Part design was possible when the natural frequency performance value of 32Hz or higher was satisfied through finite element analysis, and the temperature distribution and deformation characteristics of the part after injection molding were found through the first injection molding analysis. In addition, it can be seen that the temperature change of the primary part greatly influences the re-melting characteristics during the secondary injection. The minimum force for driving the turning die of the designed mold was calculated through structural analysis. Hydraulic system design was possible. Finally, a precise and efficient DTI mold design for the reservoir fluid tank was possible through presented multi-field CAE process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.444-447
• /
• 2008

Recently, the need of thin-walled injection molding and enhancement of its productivity is greatly increased. In this study, we designed and manufactured a injection molding system, which can mold a part with the thickness of $500{\mu}m$ and 8 cavity. And processing technique for the multi-cavity injection molding system, which is capable of mass productivity on the plastic parts, was considered. The problems of unbalance/imbalance on the molding process for the multi-cavity mold were predicted by numerical analysis using plastic injection molding commercial code. In addition, controllable system of melt front filling was introduced for a balanced filling using the mold temperature sensor on injection mold. It was shown that balanced filling with the suggested injection molding system was possible for $500{\mu}m$ plastic parts with 8 cavity layout.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.92-97
• /
• 2012

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameter and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced the shrinkage of injection molded part.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.

• 한국생산제조학회지
• /
• 제6권1호
• /
• pp.84-91
• /
• 1997

In producing moldings by using an injection mold, several variables such as the metal mold and the condition of injection molding should be selected properly in order to obtain good quality of moldings. In this study, focussed are the mechanical properties of injection moldings, since many researches on injection have been focussed mainly on the molding quality, injection pressure, and bulk temperature but the properties of injection moldings have not been studied extensively. The mechanical properties of present injection moldings can be improved simply by changing the molding material and the injection conditon without changind the metal mold. To have the final products meet the specified molding quality and mechanical properties at the same time, the bulk temperature of injection, pressure variation, volumetric shrinkage, stress, and cooling should be analized by CAE(computer aided engineering) after injection mold design. In this paper, the effects of dischare condition on mechanical properties of injection moldings are studied by testing the moldings which are injected by varying injection conditions.

• Design & Manufacturing
• /
• 제9권3호
• /
• pp.24-28
• /
• 2015

Speaking in general terms the form injection process can be described as a new process-variant of already known structural foam molding technology which roots go back to the early sixties. The most limiting factors of already know foaming processes are large cell size and the lack of uniformity of these cells as well and the inability to foam all kinds of plastic materials. In this paper, Process Study on weight change in injection rate during foaming. Experimental conditions were set as the injection speed 50,150,300 and 450 mm/s. The experiments PA, PA+GF, PP, was confirmed that the weight increase to PP+TA.

• Design & Manufacturing
• /
• 제12권2호
• /
• pp.51-56
• /
• 2018

Generally, The women was used in the cosmetic cushion fact. It has developed with the consideration of manufacturing. In this study, we designed green-friendly and element parts lower and single cushion fact containers using a single material. Injection mold simulation were performed using on 3D design data. The injection mold simulation used the data (Injection time / Cooling time / Temperature / Pressure) in the injection mold parameters. In addition, the sink mark phenomenon in the simulation results is analyzed as a problem due to the thickness and further research is needed in the future.