• Journal of Environmental Science International
• /
• v.9 no.4
• /
• pp.311-318
• /
• 2000

To improve $CO_2$pemselectivity, a modified silica membrane was prepared by chemical vapor deposition with tetraethoxysilane(TEOS)-ethanol-water, and TEOS-ethanol-water-HCI solution at 300-$600^{\circ}C$. The silica was effectively deposited in the mesopores of a ${\gamma}$-alumina film coated on a porous $\alpha$-alumina tube by evacuating the reactants through the porous wall. In this membrane, $CO_2$interacts, to some extent, with the pore wall, and $CO_2$/$N_2$selectivity then exceeds the value of the Knudsen diffusion mechanism, while the membrane derived from TEOS alone has no $CO_2$selectivity. The silica membrane prepared from TEOS-ethanol-water-HCI solution showed that $CO_2$permeance was $2.5$\times$10^{-7}mol/s^{-1}.m^{-2}.Pa^{-1} at 30{\circ}C$ and $CO_2$/$N_2$selectivity was approximately 3. The $CO_2$permeance and selectivity was improved by enlarging the surface diffusion with modification of chemical affinity of the silica pores.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.249-254
• /
• 2002

The surface of tube-type alumina substrate was modified with a silane coupling agent in order to modify the membrane surface with hydrophobicity. Contact angle of water drops on modified membrane was greater than $90^{\circ}$. The modified membrane was tested in pervaporation and vapor permeation for the recovery of menthol from dilute menthol/water mixture. With increasing menthol concentration in the feed at $45^{\circ}C$, permeation rate of menthol in pervaporation and vapor permeation increased from $0.039(g/m^2hr)$ to $0144(g/m^2hr)$ and from. $0.077(g/m^2hr)$ to $0.297(g/m^2hr)$ respectively. When feed concentration is 0.005(g/L) at $45^{\circ}C$, separation factor for menthol in pervaporation and vapor permeation is 20,7 and 40.5 respectively.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.1
• /
• pp.9-15
• /
• 2009

There is a growing demand for a high voltage silicone rubber composite with high mechanical property and high electrical property. The effect of modified cross-linking agent on the mechanical, electrical properties, and short-circuit test performance of silicone rubber insulators have been investigated. To use base polymer, the various silicone polymers were prepared by the equilibrium polymerization. Aluminum trihydrate surface was treated by vinyl silane. Liquid silicone rubber nanocomposite was prepared from the compounding of VPMPS, HPDMS, catalyst, and alumina trihydrate modified with 1,3,5-trivinyl-l,3,5-trimethylcyclotrisiloxane. The mechanical property and electrical property for insulation materials were measured, indicating the high tensile strength and the good short-circuit property.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.3
• /
• pp.247-252
• /
• 2005

The typical treatment method for fluoride polluted water is the flocculation and precipitation method which usually is capable of reducing the fluoride concentration down to the level of about 10 ppm. However, this method is no longer effective for the treatment of contaminated water having less than 10 ppm of fluorides. To remove fluorides in polluted water from the fluoride concentration between 1 to 10 ppm, several adsorbents were prepared mainly based on an activated alumina and the fluoride removal efficiencies of the adsorbents were analyzed. The best fluoride removal efficiency was obtained when the activated alumina treated by sulfuric acid was used as the adsorbent. A proper calcination temperature for the sulfuric acid contained activated alumina was found to be about $500^{\circ}C$. An adsorption isotherm for the adsorbent was also obtained by using Freundlich model. The values of the constants in Freundlich isotherm model were calculated to be K=6.63 and 1/n=0.29 based on the results obtained from the series of batch type adsorption experiments.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.143-149
• /
• 2000

Monolithic refractory technology has been developed for RH vessels, with the purpose of reducing the total refractory cost. The technology includes the use of an improved monolithic refractory and microwave drying. The improved monolithic refractory was an alumina-spinel composition, of the type used in steel ladles, to which fine alumina was added to increase the density and corrosion resistance. The microwave drying method, previously developed and used to dry the monolithic lining in steel ladles, was modified for use in drying the dense, 500mm thick lining in RH vessels. This work has resulted in significant cost savings.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.220-224
• /
• 1999

Sliding wear test was employed to determine the effect of whisker content and orientation on the firiction and wear behavior of SiC whisker reinforced alumina. Composites containing unidirectionally oriented whiskers were prepared by a modified tape casting followed by lamination, binder removal and hot pressing in order to align the whiskers in the tape casting direction. Wear coefficients on three directions were measured; parallel and normal to the tape casting direction on the tape casting surface and normal to lamination direction on surfnce normal to the tape casting direction. In the effect of whisker orientation, the highest wear rate was obtained in the direction parallel tape casting direction and the lowest in the direction normal to lamination direction at all temperatures. Silicon oxide layer amoothing the surface was detected by energy dispersive X-ray analysis on the worn surface.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.371-387
• /
• 1999

La2-xSrxCuO4 single-crystalline films were prepared on bulk single crystals of Zn-doped La2CuO4 as the substrates by LPE technique using tow deferent methods. When prepared using an alumina crucible in normal electrical furnace, the La2-xSrxCuO4 films were contaminated with less than 3 at% aluminum from the alumina crucibles. Aluminum contamination either reduced or completely destroyed the superconductivity of the La2-xSrxCuO4 films. For LPE growthby modified TSFZ method using an infrared heating furnace without crucibles, the La2-xSrxCuO4 films of x=0.11 showed superconducting with Tconset 36 K, which is 10 K higher than that in the La2-xSrxCuO4 bulk single crystals.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.6
• /
• pp.1628-1632
• /
• 2010

Porous ${\eta}-Al_2O_3$ was synthesized by modified sol-gel method using ionic liquid as a templating material. The addition of ionic liquid assisted to increase the surface area of alumina. However, the acidity of aluminas prepared with ionic liquids was hardly affected regardless the change of its structural properties. Among the ionic liquids used in this study, 1-butyl-3-methylimidazolium hexafluorophosphate ([Bmim][$PF_6$]) was the most effective ionic liquid to produce porous ${\eta}-Al_2O_3$ particles. The catalytic performance of these aluminas has been investigated in dehydration of methanol to produce dimethyl ether. The alumina prepared with [Bmim][$PF_6$] outperformed the other aluminas except ${\eta}-Al_2O_3$ without modification in this reaction.

• Journal of the Korean Ceramic Society
• /
• v.30 no.11
• /
• pp.974-978
• /
• 1993

Glass viscosity effects on the electrical properties and microstructure of RuO2 based thick film resistors (TFR) using alumina modified lead borosilicate glasses were studied. AT 85$0^{\circ}C$, the glass viscosities were increased from 4.24Pa.s to 51.5Pa.s when the alumina was added from none to 14 weight percent to the standard glass of 63% PbO, 25% B2O3 and 12% SiO2. The resistivities of resistors were generally decreased and the microstructure development was retarded as the viscosity of the glass increased. This is contrary to the generally accepted thought that the low resistivity is due to fast microstructure development kinetics in TFR. Even though the glass viscosity retards the microstructure development kinetics, the overall network formations are favored for higher viscosity of glass, such that the sheet resistivities were decreased as the glass viscosity increased.

• Journal of the Korean Ceramic Society
• /
• v.37 no.11
• /
• pp.1078-1083
• /
• 2000

정전안정화 및 입체안정화를 동시에 적용한 복합안정화기구에 의하여 25 부피%의 나노 $Al_2$O$_3$슬러리를 제조하고, 이로부터 얻은 주입성형체, 원심성형체, 진공성형체의 기공구조 분석을 통하여 입자충전거동을 살펴보았다. 나노 알루미나 분말의 습식 성형체의 충전구조는 성형방법에 의하여 가해지는 외력의 영향을 크게 받지만, 반발력을 제공하는 표면장벽층의 상호작용에 의해서도 현저한 차이를 보이는 것으로 나타났다. 예비소결실험을 통하여 나노분말에서도 기공크기가 작고, 크기분포가 좁으며, 높은 밀도를 가진 균일성형체의 미세구조가 소결미세구조를 균일하게 하는데 필수적인 조건임을 확인하였다.