• International Journal of Computer Science & Network Security
• /
• v.23 no.10
• /
• pp.1-10
• /
• 2023

This paper proposes a method to extend Inter-Carrier Interference (ICI) canceling Orthogonal Frequency Division Multiplexing (OFDM) receivers for 5G mobile systems to spatial multiplexing 2×2 MIMO (Multiple Input Multiple Output) systems to support high-speed ground transportation services by linear motor cars traveling at 500 km/h. In Japan, linear-motor high-speed ground transportation service is scheduled to begin in 2027. To expand the coverage area of base stations, 5G mobile systems in high-speed moving trains will have multiple base station antennas transmitting the same downlink (DL) signal, forming an expanded cell size along the train rails. 5G terminals in a fast-moving train can cause the forward and backward antenna signals to be Doppler-shifted in opposite directions, so the receiver in the train may have trouble estimating the exact channel transfer function (CTF) for demodulation. A receiver in such high-speed train sees the transmission channel which is composed of multiple Doppler-shifted propagation paths. Then, a loss of sub-carrier orthogonality due to Doppler-spread channels causes ICI. The ICI Canceller is realized by the following three steps. First, using the Demodulation Reference Symbol (DMRS) pilot signals, it analyzes three parameters such as attenuation, relative delay, and Doppler-shift of each multi-path component. Secondly, based on the sets of three parameters, Channel Transfer Function (CTF) of sender sub-carrier number n to receiver sub-carrier number l is generated. In case of n≠l, the CTF corresponds to ICI factor. Thirdly, since ICI factor is obtained, by applying ICI reverse operation by Multi-Tap Equalizer, ICI canceling can be realized. ICI canceling performance has been simulated assuming severe channel condition such as 500 km/h, 8 path reverse Doppler Shift for QPSK, 16QAM, 64QAM and 256QAM modulations. In particular, 2×2MIMO QPSK and 16QAM modulation schemes, BER (Bit Error Rate) improvement was observed when the number of taps in the multi-tap equalizer was set to 31 or more taps, at a moving speed of 500 km/h and in an 8-pass reverse doppler shift environment.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.6
• /
• pp.11-18
• /
• 2009

In this paper, a hierarchical link allocation algorithm between mobile stations (MSs) and the corresponding base station (BS) by an optimal utilization of relay stations (RSs) is proposed to improve throughput of RS systems. In the proposed hierarchical algorithm, each RS operates cognitive radio functions to sense the degree of satisfaction in the quality of services (QoSs) and then selects the candidate set of MSs to have links with the RS. Such information is reported to the BS, where an auction process is performed to get an optimal allocation of communication links between the MSs and the BS. To maximize system throughput, the proposed auction algorithm is conducted upon bidding prices of communication links, considering both the co-channel interference (CCI) information shared among adjacent cells and the QoS enhancement information for each MS collected from RSs. The BS then switches the communication links of the auction winner MSs through the corresponding RS. The computer simulation shows that the proposed algorithm enhances the user QoS more than the conventional algorithm, especially for RS systems with more users requiring higher QoS. The proposed algorithm has also been proved to have more robust performance than the conventional one when the traffic load is higher and the CCI becomes stronger.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.48-57
• /
• 1999

안테나 단에서 직접 수신 신호의 디지털화가 이루어지고 그 해당 신호의 처리는 고속 디지털 신호처리기 내에서 소프트웨어로 수행되는 방식을 SWR(Software Radio)이라 한다. 그러나 현재의 기술 수준을 감안하여 보다 현실적인 SDR(Software Defined Radio) 정의가 필요하게 되었다. SDR이란 수신신호의 디지털화가 안테나 이하의 임의의 단(IF단)에서 이루어지는 무선으로 정의된다. 물론 A/D변환기등의 기술이 더욱 발전되면 궁극적으로는 SWR로 진화될 것이다. 그러면 SDR은 왜 필요한 것일까? 현재 사용중인 이동통신 단말기의 단점은 어느 한 표준 또는 방식에 종속되어 언제 어디서나 임의의 시스템에 접속되어 사용하기에는 많은 기술 종속적인 문제 및 제약을 내포하며, 사용방식에 따른 시스템의 유연성이 없고, 상용 서비스 도중에 발생되는 단말기 문제의 해결(recall service)이 어렵고, 많은 기술료를 지불해야 한다는 것이다. 부연하면 CDMA 셀룰라의 경우 퀄컴 등의 특정한 회사에 의해 기술이 폐쇠되어, 정보의 흐름이 자유스럽지 못할 뿐더러, 이로 인해 기술진화가 보다 빠르게 진행되지 못하고, 전세계적으로 많은 새로운 우수 제품의 출연에 제약이 가해진다는 것이다. 따라서 SDR(Software Defined Radion)을 도입, 하드웨어 및 소프트웨어를 개방형 구조(open architecture)로 개발한다면 정보의 흐름을 자유롭게 할 수 있고, 이로 인하여 세계적으로 다양한 신제품의 개발이 촉진되고 결과적으로 전세계 시장이 커지게 되는 일석이조의 효과를 얻을 수 있게 된다. 또한 이 같은 개방형 단말기 개발의 필요성은 최근 시장동향으로 볼 때, 기존의 단말기 회사 입장에서는 새로운 수익 모델이 필요한 시점이고, 또한 2002년경에 판매되는 단말기의 80%정도는 멀티모드타입 단말기일 것으로 예측되는 점, 그리고 금년말까지 100개 회사 이상이 SDR 포럼 멤버로 가입할 것으로 예측되는 점, 무선 인터넷 폭발적인 성장으로 복합 멀티미디어 단말기 시대가 다가오는 점 등으로 미루어 볼 때, 고객의 서비스 가치선택에 역점을 둔 기술을 중시해야 한다는 점에서 더욱 설득력을 지닌다. 따라서 이 같은 목적과 3세대 이동통신 및 인터넷 사용자의 증가, 반도체기술의 발전에 힘입어, 과거 군용 시스템에서 이용되던 SWR 기술을 상용시스템 특히 3세대 이동통신에 적용하려는 연구가 활발히 진행되고 있다. '96년 SDR 포럼이 결성되었는데, 목적은 휴대형 장치(hand-held devices), 기지국(base stations), 차량형 장치(mobile stations)를 포함하는 다중모드(multi-mode), 다중대역(multi-band) SDR을 위한 개방형 구조의 표준을 정하기 위함이다. 이 같이 public forum에 의한 표준(open architecture standard)이 정해지면 그 다음은 이를 어떻게 구현할 것인가가 문제가 될 것이다. 본고에서는 먼저 SDR 단말기 요구사항을 살펴보고, 이 요구사항들을 만족하는 SDR 단말기 구조, SDR 계층참조 모델, 그리고 기존의 단말기 구조와 SDR 계층참조 모델의 연관관계에 대해 살펴보고, 크게 두가지 종류의 단말기 즉 사용 SDR 단말기와 군용 SDR 단말기에 대해 살펴보고, 설계 절차 및 현재 시점에서 단말기 구현을 위해 해결해야 하는 기술적 과제를 살펴보고 결론을 언급한다.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.7
• /
• pp.1804-1820
• /
• 1997

In this paper, an efficient call control procedure is presented for next generation wireless ATM networks and its performance is mathematically analyzed using the open queueing network. This procedure is based on a new scheme called as the cell clustering. When we use the cell clustering scheme, at the time that a mobile connection is admitted to the network, a virtual cell is constructed by choosing a group of neighboring base stations to which the call may probabilistically hand over and by assigning to the call a collection of virtual paths between the base stations. Within a microcell/picocell environment, it is seen that the cell clustering can support effectively a very high rate of handovers, provides very high system capacity, and guarantees a high degree of frequency reuse over the same geographical region without requiring the intervention of the network call control processor each time a handover occurs. But since mobiles, once admitted, are free to roam within the virtual cell, overload condition occurs in which the number of calls to be handled by one base station to exceed that cell site's capacity of radio channel. When an overload condition happens, the quality of service is abruptly degraded. We refer to this as the overload state and in order to quantify the degree of degradation we define two metrics, the probability of overload and the normalized average time spent in the overload state. By using the open network queueing model, we derive closed form expressions for the maximum number of calls that can be admitted into the virtual cell such that the two defined metrics are used as the acceptance criteria for call admission control.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.10
• /
• pp.1517-1524
• /
• 2022

In this paper, we consider a heterogeneous network (HetNet) consisting of one macro base station and multiple small base stations, and assume the coordinated multi-point transmission between the base stations. In addition, we assume that the channel between the base station and the user consists of path loss and Rayleigh fading. Under these assumptions, we present the energy efficiency (EE) achievable by the user for a given base station and we formulate an optimization problem of dynamic cell selection and transmit power allocation to maximize the total EE of the HetNet. In this paper, we propose an unsupervised deep learning method to solve the optimization problem. The proposed deep learning-based scheme can provide high EE while having low complexity compared to the conventional iterative convergence methods. Through the simulation, we show that the proposed dynamic cell selection scheme provides higher EE performance than the maximum signal-to-interference-plus-noise ratio scheme and the Lagrangian dual decomposition scheme, and the proposed transmit power allocation scheme provides the similar performance to the trust region interior point method which can achieve the maximum EE.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.12
• /
• pp.131-139
• /
• 2022

In this paper, to verify the authenticity of UxNB that assists terrestrial base stations, the solutions for SI (System Information) security presented in 3GPP TR 33.809 are analyzed from the perspective of UxNB. According to the definition of 3GPP (Third Generation Partnership Project), UxNB is a base station mounted on a UAV (Unmanned Aerial Vehicle), is carried in the air by the UAV, and is a radio access node that provides a connection to the UE (User Equipment). Such solutions for SI security can be classified into hash based, MAC (Message Authentication Codes) based, and digital signature based, and a representative solution for each category is introduced one by one. From the perspective of verifying the authenticity of UxNB for each solution, we compare and analyze the solutions in terms of provisioning information and update, security information leakage of UxNB, and additionally required amount of computation and transmission. As a result of the analysis, the solution for verifying the authenticity of the UxNB should minimize the secret information to be stored in the UxNB, be stored in a secure place, and apply encryption when it is updated over the air. In addition, due to the properties of the low computing power of UxNB and the lack of power, it is necessary to minimize the amount of computation and transmission.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.10
• /
• pp.937-945
• /
• 2014

As various services requiring high data rate are supported by introducing LTE/LTE-adv., mobile traffic increases rapidly. To cope with the continuous growth of traffic demand, small cell technology is considered as one of the most promising one. Small cell can increase system capacity by increasing the number of base stations with reduced cell radius. In this paper, we analyze the effect of cell densification with small cells in terms of SINR and average UE throughput considering cell split and the number of UE per unit area. As the cell becomes smaller, SINR degradation arises from high ICI(Inter Cell Interference) and we evaluate the effect of interference mitigation scheme in small cell environment where the proper interference mitigation technique is applied.

• Journal of Advanced Navigation Technology
• /
• v.11 no.4
• /
• pp.415-422
• /
• 2007

In this paper, we proposed a new dynamic channel allocation algorithm for TD-SCDMA with cross time slots. In order to reduce the interference in cross time slot, the mobile stations (MSs) are divided into two groups: the Near Group consisting of MSs near by the base station(BS) and the Far Group including the MSs far from the BS. The reverse link for MSs in the Near Group and forward link for MSs in the Far Group are allocated to the cross time slot. In cellular systems, a BS has multiple neighbor BSs. Some of neighbor BSs can operate in the same direction link while the others have cross time slot. Thus, it is required to determine which BS has the most significant impact in terms of interference. We divide each cell into 6 areas based on the direction of arrival of smart antenna and the most significant neighbor sector is determined with this division. The proposed allocation method and area division method can avoid the severe interference in cross time slots and increase the system capacity about 2%~9% compared to FCA, and 0.5%~1.3% compared to RCA.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.1
• /
• pp.17-28
• /
• 2014

The increase of smartphone users have made mobile carriers offload increasingly congested traffic of 3/4G by providing Wi-Fi hot-spots in the public places such as coffee shops and subway stations. In the traditional authentication in WLAN, the users should convince the service providers that they are valid customers before they use WLAN services. Since the authentication protocol is designed for service providers. Even with the mutual authentication based on the IEEE 802.1X, which is supported by IEEE 802.11 standard, it is difficult to be convinced of that the service providers really have installed the WLAN APs, which users are confronted with. An attacker can install rogue APs that masquerade as legitimate APs by copying the SSID, MAC address, etc. in order to obtain users' private information. In this paper, we introduce a method of authenticating legitimate APs for smartphone users. And we show our proposal can be well utilized for the current Wi-Fi hot-spots as a security plug-in and prove it through our experiments.

• Journal of Communications and Networks
• /
• v.17 no.1
• /
• pp.58-66
• /
• 2015

Aeronautical communication networks (ACN) is an emerging concept in which aeronautical stations (AS) are considered as a part of multi-tier network for the future wireless communication system. An AS could be a commercial plane, helicopter, or any other low orbit station, i.e., Unmanned air vehicle, high altitude platform. The goal of ACN is to provide high throughput and cost effective communication network for aeronautical applications (i.e., Air traffic control (ATC), air traffic management (ATM) communications, and commercial in-flight Internet activities), and terrestrial networks by using aeronautical platforms as a backbone. In this paper, we investigate the issues about connectivity, throughput, and delay in ACN. First, topology of ACN is presented as a simple mobile ad hoc network and connectivity analysis is provided. Then, by using information obtained from connectivity analysis, we investigate two communication models, i.e., single-hop and two-hop, in which each source AS is communicating with its destination AS with or without the help of intermediate relay AS, respectively. In our throughput analysis, we use the method of finding the maximum number of concurrent successful transmissions to derive ACN throughput upper bounds for the two communication models. We conclude that the two-hop model achieves greater throughput scaling than the single-hop model for ACN and multi-hop models cannot achieve better throughput scaling than two-hop model. Furthermore, since delay issue is more salient in two-hop communication, we characterize the delay performance and derive the closed-form average end-to-end delay for the two-hop model. Finally, computer simulations are performed and it is shown that ACN is robust in terms of throughput and delay performances.