• Transactions on Electrical and Electronic Materials
• /
• v.6 no.4
• /
• pp.173-176
• /
• 2005

A new $MoO_3$ based microsensor with low power consumption was presented. Typical size of sensor was 5mm in width and 8mm in length. As a sensitive electrode, $MoO_3$ was successfully fabricated by IC technology on pyrex glass of $250{\mu}m$ in thickness. After annealing at $550^{\circ}C$ for 3hrs, the film was fully crystallized and demonstrated as pure $MoO_3$ structure. The grain size of $MoO_3$ was plat like and typical size was about $1{\mu}m$. Based on the results of sensitivity measurement, $MoO_3$ microsensor shows especially high selectivity to $H_2$ reducing gas atmosphere. The applied heater power was lower than 0.5 Watt.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.348-355
• /
• 2023

Magnesium secondary batteries are attracting much attention due to their potential to replace conventionally used lithium ion batteries. Magnesium secondary battery cathode material Mo₆S₈ were synthesized by molten salt synthesis method and PVC as a carbon materials were added to improve electrochemical properties. Crystal structure, size and surface of the synthesized anode materials were measured through XRD and SEM. Charge-discharge profiles and rate capabilities were measured by battery test system. 2.81 wt% PVC coated sample showed the best rate capabilities of 85.8 mAh/g at 0.125 C-rate, 69.2 mAh/g at 0.5 C-rate, and 60.5 mAh/g at 1 C-rate.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.414-422
• /
• 2002

Three different multi-component white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their as-cast and solidification structures. Three combinations of the alloying elements were selected so as to obtain the different types of carbides and matrix structures : 3%C-10%Cr-5%Mo-5%W(alloy No.1), 3%C-10%V-5% Mo-5%W(alloy No. 2) and 3%C-17%Cr-3% V(alloy No.3). The as-cast microstructures were investigated with optical and scanning electron microscopes. There existed two different types of carbides, $M_7C_3$ carbide with rod-like morphology and $M_6C$ carbide with fishbone-like one, and matrix in the alloy No. 1. The alloy No. 2 consisted of MC carbide with chunky and flaky type and needle-like $M_2C$ carbide, and matrix. The chunky type referred to primary MC carbide and the flaky one to eutectic MC carbide. The morphology of the alloy No. 3 represented a typical hypo-eutectic high chromium white cast iron composed of rod-like $M_7C_3$ carbide which is very sensitive to heat flow direction and matrix. To clarify the solidification sequence, each iron(50g) was remelted at 1723K in an alumina crucible using a silicon carbide resistance furnace under argon atmosphere. The molten iron was cooled at the rate of 10K/min and quenched into water at several temperatures during thermal analysis. The solidification structures of the specimen were found to consist of austenite dendrite(${\gamma}$), $ ({\gamma}+ M_7C_3)$ eutectic and $({\gamma}+ M_6C)$ eutectic in the alloy No. 1, proeutectic MC, austenite dendrite(${\gamma}$), (${\gamma}$+MC) eutectic and $({\gamma}+ M_2C)$ eutectic in the alloy No. 2, and proeutectic $M_7C_3$ and $ ({\gamma}+ M_7C_3)$ eutectic in the alloy No 3. respectively.

• Bulletin of the Korean Chemical Society
• /
• v.14 no.2
• /
• pp.266-271
• /
• 1993

The reaction of $(CO_5$)M=C(OMe)Tol (M=Cr, Mo, W and $Tol=p-C_6H_4Me)$ and $BBr_3$ followed by treatment with tetramethylethylenediamine (TMEDA) yields a mixture of two diastereomers, trans, $cis-Br(CO)_2(tmeda)M{\equiv}$CTol [M=Cr(1a), Mo(2a), W(3a)] and cis, $trans-Br(CO)_2(tmeda)M{\equiv}$CTol [M=Cr(1b), Mo(2b), W(3b)], respectively. These compounds have been isolated as crystalline solids and characterized by spectroscopic (infrared, mass, $^1H$ and $^{13}C-NMR)$ data. The trans, cis-Br(CO)2(tmeda)Cr${\equiv}$CTol (1a), has been examine via a single crystal X-ray diffraction study : $BrCrO_2N_2C_{16}H_{23}$, Mr=407.27, triclinic, $P{\bar{1}},\;a=12.792(2),\;b=13.400(5),\;c= 11.645(4)\;{\AA},\;{\alpha}=101.26(2)^{\circ},\;{\beta}=103.04(2)^{\circ},\;{\gamma}=91.88(2)^{\circ},\;{\nu}=1907(1){\AA}^3,\;Z=2,\;{\rho}(calcd)=1.418\;gcm^{-3},\;{\lambda}(MoK{\alpha})=0.71069\;{\AA},\;{\mu}=26.25 cm^{-1},\;F(000)=831.97,\;T=295K,\;R=0.0977$ for 1332 significant reflections $[F_0>5{\sigma}(F_0)]$. There are two essentially equivalent molecules in the crystallographic asymmetric unit. Each molecule is octahedral with the bromide ligand trans to the alkylidyne carbon, the two cis-carbonyl ligands, and the bidentate TMEDA ligand.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.62-68
• /
• 2004

In this study, SHS process has been employed to fabricate porous $MoSi_2$ material with electric-resistive heating capability through the control of pore size. The preform for SHS reaction was consisted of molybdenum powder with different sizes and silicon powder with different contained quantity. The size of the $MoSi_2$ particles thus formed was determined by the generated heat of combustion, not by the size of molybdenum powder. However, the pore size of $MoSi_2$ composite was proportional to the particle size of molybdenum powder. that is the coarser the molybdenum powder used, the larget the formed pore size. Based on these results, the porous $MoSi_2$ composite could be fabricated with a desired pore size. By orienting the porous molybdenum disilicide-based material in the form of pore size gradient, porous materials used for filters with improved dirt-holding capacity can be manufactured.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.2
• /
• pp.43-52
• /
• 2017

Heat treatment condition for dissolution of the M23C6 carbides in 2.25Cr-1Mo-V-Ti material for thermal power plant tube was investigated using a dilatometer method. 2.25Cr-1Mo-V-Ti material was heat-treated at $900{\sim}1,100^{\circ}C$ for 0, 10, 30 min to find the proper dissolution condition of M23C6 carbides. The phase identification and volume fraction of the carbide were measured by using OM, SEM, EBSD and TEM analysis. Optimal heat treatment condition of M23C6 carbide dissolution was selected by predicting dissolution temperature of carbide using Bs points appeared at dilatometer curve. Experimental results showed that the conditions of carbide dissolution was 900, 1,000, $1,100^{\circ}C$ for 30 min. Eventually, the optimal heat treatment condition for dissolution was 30 min at $1,000^{\circ}C$ considering the minimum coarsening of Austenite grain size.

• Journal of Korea Foundry Society
• /
• v.16 no.2
• /
• pp.141-148
• /
• 1996

In high chromium cast iron, the control of matrix microstructure as well as carbide structure is important to the performance as a wear resistant material. In this study, 3.0% C-24.0% Cr white cast irons with various molybdenum contents(residual, 1.0%, 3.0% and 5.0%) were solidified conventionally and unidirectionally for studying their effects on the microstructure and hardness. In the conventional casting, two sets of castings were poured from each melt. One set of the castings consisted of cylindrical bars of 10 and 20mm by 155mm long. The second set of the castings was a cylindrical bar of 30mm by 200mm long. On the other hand, a pep-set mold set on the Cu plate was employed to make the solidification unidirectionally. X-ray diffraction method was used to observe retained austenite and carbides in the high chromium cast iron. The morphology of eutectic $M_7C_3$ carbides changed from needle-like type to nodular type with the increase of Mo content. And, the presence of $M_2C$ carbides was identified in the sample where Mo was added over 3.0 %. Primary and eutectic carbides appeared as rod type and corngrain type, respectively in the unidirectionally solidified samples which were cut to parallel to the solidification direction. In the EDX analysis, Cr concentration was higher in the primary and eutectic $M_7C_3$ carbides, Mo in the $M_2C$ carbides, and Fe in the matrix.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.615-620
• /
• 1996

Chromium-Molybdenum steel was plasma-nitrided at 823 K for 10.8 ks in an atmosphere of 30% $N_2$-70% $H_2$ gas under 665 Pa without and with a subsidiary cathode of $MoS_2$ to compare ion-nitriding and plasma-sulfnitriding using subsidiary cathode. When the steel was ion-nitrided without $MoS_2$, iron nitride layer of 4$\mu\textrm{m}$ and nitrogen diffusion layer of 400mm were formed on the steel. A compound layer of 15$\mu\textrm{m}$ and nitrogen diffusion layer of 400$\mu\textrm{m}$ were formed on the surface of the steel plasma-sulfnitrided with subsidiary cathode of $MoS_2$. The compound layer consisted of FeS containing Mo and iron nitrides. The nitrides of $\varepsilon$-$Fe_2$, $_3N$ and $\gamma$-$Fe_4N$ formed under the FeS. The thicker compound layer was formed by plasma-sulfnitriding than ion-nitriding. In plasma-sulfnitriding, the surface hardness was about 730 Hv. The surface hardness of the steel plasma-sulfnitrided with $MoS_2$ was lower than that of ion-nitrided without $MoS_2$. This may be due to the soft FeS layer formed on the surface of the plasma-sulfnitrided steel.

• Bulletin of the Korean Chemical Society
• /
• v.11 no.2
• /
• pp.109-114
• /
• 1990

The anionic transition metal hydrides $(HW(CO)_4P(OMe)_3\;^-,\;HW(CO)_5\;^-,\;HCr(CO)_5\;^-,\;HFe(CO)_4\;^-)$ react with transition metal alkyl $(CpMo(CO)_3(CH_3)$ to yield $CH_4\;and\;CH_3CHO$ in addition to the inorganic products $(CpMo(Co)_3\;^-$, etc.). The reaction of these anionic metal hydrides with CpMo(CO)3{CH2CH(CH2)2} may lead to an elucidation of the reaction mechanisms involved; the organic product distributions are among $CH_4,\;CH_2\;=\;CHCH_2CH_3$, and $CH_3CH(CH_2)_2$, depending upon the anionic metal hydride used. These anionic metal hydrides also are reported to undergo a hydride-halide exchange reaction with organic halides; therefore, these similar reactions have been compared in terms of leaving group ability $(CpMo(CO)_3\;^-\;vs.\;Br^-)$ and the mechanistic pathways.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.129-129
• /
• 2003