• Journal of Korean Port Research
• /
• v.14 no.2
• /
• pp.241-249
• /
• 2000

The amount of municipal water has been increased rapidly up to now and it is necessary to treat and dispose the wastewater effectively. The recent trend of the effluent disposal system, after treatment, show a nearshore discharge which has an outfall with length somewhere between the shoreline discharge and an extended deepwater outfall. There is no universal solution to municipal water treatment and disposal and each case must be examined on its merits and on economic, technical and environmental bases. In this study we focused mostly on the scientific and engineering aspects of ocean disposal through the outfall. For this purpose, we made an investigation to the near-field characteristics of discharged water and made some comparison with the existing experimental results. We also applied it to the Pusan Jungang Effluent Outfall System, which is planned to build in the Gamchun harbour and will be completed in 2011. The model output showed the trajectoral variation of dilution and mixing behavior for three cases of outfall system. Dilution differences have been simulated and found the highest dilution condition under the different displacement of outfall system. On the basis of these outputs it will be proposed the optimum outfall system type and location.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.3
• /
• pp.59-65
• /
• 1999

This study has been performed to confirm the three dimensional effect of the crack reduction and the restrained effect of crack growth for the synthetic fiber reinforced soil. Two types of polyrpropylene fiber and low plastic clay(CL) were used for the test. And the test variable were fiber length and so on. The results of the study were summarized as follows ; 1) The mixing of synthetic fiber was effective in reducing crack growth due to adhesion between soil partlcles and synthetic fiber.l Especially initlal crack was delayed, as compared with the pure soil, for about 1 day in case of mono filament synthetic fiber and for about 1 or 2 days in case of fibrillated syntetic fiber. 2) As the content and length of synthetic fiber were increased , the effect of crack reduction was increased. It was found that 0.5% fibrillated synthetic fiber with 40mm length reinforced soil had about 3 times more effective than natural soils. 3) In case of the same fiber content and fiber length, the fibrillated synthetic fiber has nmore effective than the mono filament synthetic fiber for crack reduction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.1
• /
• pp.132-142
• /
• 2000

The objective of this study is to experimentally investigate the noise propagating characteristics, the noise reduction mechanism and the performance of a slotted tube attached at the exit plane of a circular convergent nozzle. The experiment is performed through the systematic change of the jet pressure ratio and the slot length under the condition of two kinds of open area ratios, 25% and 51%. The open area ratio calculated by the tube length equivalent for the slot length is defined as the ratio of the total slot area to the surface area of a slotted tube. The experimental results for the near and far field sound, the visualization of jet structures and the static pressure distributions in the jet passing through a slotted tube are presented and explained in comparison with those for a simple tube. The propagating characteristics of supersonic jet noises from the slotted tube is closely connected with the slot length rather than the open area ratio, and its propagating pattern is similar to the simple tube. It is shown that the slotted tube has a good performance to suppress the shock-associated noise as well as the turbulent mixing noise in the range of a limited jet pressure and slot dimension. The considerable suppression of the shock‘associated noise is mainly due to the pressure relief caused by the high-speed jets passing through the slots on the tube. Both the strength of shock waves and the interval between them in a jet plume are decreased by the pressure relief. Moreover, the pressure relief is divided into the gradual and the sudden relief depending upon the open area ratio of the slotted tube. Consequently, the shock waves in a jet plume are also changed by the type of pressure relief. The gradual pressure relief caused by the slotted tube with the open area ratio 25% generates the weak oblique shock waves. On the contrary, the weak normal shock waves appear due to the sudden pressure relief caused by the slotted tube with the open area ratio 51%.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2018.10a
• /
• pp.133-133
• /
• 2018

The aim of this study was to evaluate the effect of charcoal on germination and early growth of barley sprouts. Five treatments were employed based on different amount and treatment method along with control. Barley seeds were soaked in water for 8 hours. Two types of topping treatment were applied such as, charcoal: 100 g (designated as T1) and charcoal: 200 g (T2). Three kinds of mixing treatment were as follows: barley seeds were mixed with 100g of charcoal (designated as M1), with 200g of charcoal (M2), and with 300g of charcoal(M3). The control did not have any charcoal. In our finding, germination rates were observed 53.3% (control), 26.3%(T1), 36.3%(T2), 67.3%(M1), 81.7%(M2), and 79.7%(M3) at three days after inoculation (DAI). Length of radicle was found at 0.90 cm (control), 0.88 cm (T1), 0.99 cm (T2), 1.03cm (M1), 1.66 cm (M2), and 0.70 cm (M3) in 3 DAI. In addition, sprout length was found 4.5 cm (control), 10.4 cm (T1), 11.9 cm (T2), 5.7 cm (M1), 6.3 cm (M2), and 2.1 cm (M3) in 14 DAI. Fresh weight of sprouts were 0.78g (control), 1.03g (T1), 1.07g (T2), 0.96g (M1), 1.07g (M2), and 0.95g (M3). Among the treatment, topping of seeds on 200g of charcoal (T2) showed longest sprout length and fresh weight. Mixing treatments showed higher germination rates and sprout fresh weight. The results may be attributed to difference in micro-climate conditions (mostly temperature and humidity) in the growth boxes in different treatments.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.93-98
• /
• 2007

The air velocity flowing in inner combustion chamber of SCramjet is supersonic and the time of its stay is very short as a few milliseconds. Within this short time, fuel injection， air-fuel mixing, and combustion process should be accomplished. Several methods are suggested for mixing enhancement. Among these, cavity is selected to study for mixing characteristics. The numerical simulation is performed in the case of freestream Mach number of 2.5 and cavity located in front of fuel jet injection. 3 different sized cavities of the same length-height ratio were used in order to recognize the effect about cavity size. Also, the case without cavity was analyzed to find the effect of cavity. Used code compared with the result of experiment under identical conditions and it was verified. Through this comparison and verification, mixing enhancement by cavity size could be confirmed.

• Resources Recycling
• /
• v.24 no.6
• /
• pp.61-68
• /
• 2015

In this study, the strength properties of NHL based mortar with blending basalt fiber were investigated. In the first step, it was evaluated that physical properties of NHL based mortar according to mixing method of four types of basalt fiber and then mixing method of one type was selected. As a result of assessment, it showed that the physical properties with mixing method of dry blending were better than that of wet blending and mixing method that basalt fiber pre-mixed with NHL for 5 min in a blender was selected and water and aggregate were finally added. Secondly, the investigation of blending fiber length on the compressive and flexural strength for basalt fiber reinforced NHL based mortars was carried out. The compressive strength was decreased with adding fiber, and the flexural strength was increased more than plain mortar. In the case of adding 6 mm fiber, the compressive and flexural strength were improved more than that of others.

• Journal of the Korean Geosynthetics Society
• /
• v.20 no.4
• /
• pp.19-32
• /
• 2021

In this study, evaluation and consideration of domestic/overseas design, construction, and quality control performed by the authors on the deep cement mixing method were performed, and improvements for the development of the DCM method were suggested in the future. As a result of this study, it was found that the cross-sectional area correction for strength is required during the laboratory test of mix proportion, and caution is required because the extrapolation method may lead to different results from the actual one. Applicable design methods should be selected in consideration of both the improvement ratio and the type of improvement during design, and it was confirmed that the allowable compressive strength to which the safety factor was applied refers to the standard value for stability review and not the design parameters. In the case of the stress concentration ratio, rather than applying a conventional value, it was possible to perform economical design by calculating the experimental and theoretical stress concentration ratio reflecting the design conditions. In the case where pre-boring is expected during construction, if the increased water content is not large compared to the original, there were cases where a major problem did not occur even if the result that did not consider the increase in water content was used. In addition, it was confirmed that when the ratio of the top treatment length to the improved length is high, a small amount of design cement contents per unit length can be injected during construction. In the case of quality control, it was evaluated that D/4~2D/4 for single-axis and D/4 point for multi-axis were optimal for coring of grouting mixtures. As an item for quality control, it is judged that the standard that considers the TCR along with the unconfined compressive strength of grouting mixtures is more suitable for the domestic situation.

• Nuclear Engineering and Technology
• /
• v.55 no.12
• /
• pp.4357-4366
• /
• 2023

MARS-KS, a domestic regulatory confirmatory code of Republic of Korea, had been developed by integrating RELAP5/MOD2 and COBRA-TF. The integration of COBRA-TF allowed to extend the capability of MARS-KS, limited to one-dimensional analysis, to multi-dimensional analysis. The use of COBRA-TF was mainly focused on subchannel analyses for simulating multi-dimensional behavior within the reactor core. However, this feature has been remained as a legacy without ongoing maintenance. Meanwhile, MARS-KS also includes its own multidimensional component, namely MULTID, which is also feasible to simulate three-dimensional convection and diffusion. The MULTID is capable of modeling the turbulent diffusion using simple mixing length model. The implementation of the turbulent mixing is of importance for analyzing the reactor core where a disturbing cross-sectional structure of rod bundle makes the flow perturbation and corresponding mixing stronger. In addition, the presence of this turbulent behavior allows the secondary transports with net mass exchange between subchannels. However, a series of assessments performed in previous studies revealed that the turbulence model of the MULTID could not simulate the aforementioned effective mixing occurred in the subchannel-scale problems. This is obvious consequence since the physical models of the MULTID neglect the effect of mass transport and thereby, it cannot model the void drift effect and resulting phasic distribution within a bundle. Thus, in this study, the turbulence mixing model of the MULTID has been improved by means of the inter-channel mixing model, widely utilized in subchannel analysis, in order to extend the application of the MULTID to small-scale problems. A series of assessments has been performed against rod bundle experiments, namely GE 3X3 and PSBT, to evaluate the performance of the introduced mixing model. The assessment results revealed that the application of the inter-channel mixing model allowed to enhance the prediction of the MULTID in subchannel scale problems. In addition, it was indicated that the code could not predict appropriate phasic distribution in the rod bundle without the model. Considering that the proper prediction of the phasic distribution is important when considering pin-based and/or assembly-based expressions of the reactor core, the results of this study clearly indicate that the inter-channel mixing model is required for analyzing the rod bundle, appropriately.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2817-2822
• /
• 2007

The purpose of this paper is to study the influence of operating condition and ejector geometries on the hydrodynamics and on the mass transfer characteristic of ejector. The CFD results were validated with available experimental data. Flow field analyses and predictions of ejector performance were also carried out. Variation on the operating conditions was made by varying the gas-liquid flow rate ratio in the range of 0.2 to 1.2. The ejector configuration was also varied on the length to diameter ratio of mixing tube ($L_M/D_M$) in the range of 4 to 10. CFD studies show that at $L_M/D_M$ 5.5, the volumetric mass transfer coefficient increases with respect to gas flow rates. Meanwhile, at $L_M/D_M$ 4, the plot of volumetric mass transfer coefficient to gas-liquid flow rates ratio reach maximum at gas-liquid flow rates ratio of 0.6. This study also shows that volumetric mass transfer coefficient decrease with respect to the increase of mixing tube length.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.105-114
• /
• 1993

The ciculation due to bottom density current produced by a dense inflow into a small reservoir is analysed by numerical scheme. Before the front of the density current arrives at the downstream end, the mixing in the reservoir is mainly caused by the anticlockwise vortex formed at the downstream of plunging point along the movement of bottom density current. Upon the arrival of the front of the density current at the downstream end an internal surge is created through an internal hydraulic jump. With repeated propagation of the internal surge back and forth the mixing in the reservoir is progressed and the thickness of dense layer is increased upward. The dilution of the overflow at downstream end is found to depend on inflow densimetric Froude number, reservoir length and elapsed time. The time required for the overflow to attain a specified dilution increases as reservoir length increases and Fre decreases.