• Journal of the Korean Vacuum Society
• /
• v.4 no.3
• /
• pp.270-274
• /
• 1995

The growth structure of Fe on CU(001) was studied by scanning tunneling microscope. An analysis of size distribution of Fe islands on Cu(001) surface was made to determine whether Fe atoms mix with substrate Cu. The size distribution deviates from the standard scaling behavior, indicating that atomic density of Fe decreases with coverage up to 1 ML. The growth can be characterized by layer-by-layer scheme from 1 ML to 5 ML. This result agrees well with previously studied, Auger spectroscopy and RHEED result.

• Journal of Mechanical Science and Technology
• /
• v.19 no.12
• /
• pp.2281-2288
• /
• 2005

Because an injected spray development process consists of impinging and free spray in the diesel engine, it is needed to analyze the impinging spray and free spray, simultaneously, in order to study the diesel spray behavior. To dominate combustion characteristics in diesel engine is interaction between injected fuel and ambient gas, that is, process of mixture formation. Also it is very important to analyze liquid and vapor phases of injected fuel on the investigation of mixing process, respectively and simultaneously. Therefore, in this study, the behavior characteristics of the liquid phase and the vapor phase of diesel spray was studied by using exciplex fluorescence method in high temperature and injection pressure field. Finally, it can be confirmed that the distribution of vapor concentration is more uniform in the case of the high injection than in that of the low injection pressure.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.826-831
• /
• 2019

Experimental data of phase equilibrium is reported for caprolactone acrylate in supercritical carbon dioxide. Bubble-point data was measured by synthetic method at temperatures ranging from (313.2 to 393.2) K and pressures up to 55.93 MPa. In this research, the solubility of carbon dioxide for the (carbon dioxide + caprolactone acrylate) system decreases as temperature increases at a constant pressure. The (carbon dioxide + caprolactone acrylate) system exhibits type-I phase behavior. The experimental result for the (carbon dioxide + caprolactone acrylate) system was correlated with Peng-Robinson equation of state using mixing rule. The critical property of caprolactone acrylate was predicted with the Joback and Lyderson method.

• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.109-116
• /
• 2014

The flexural behavior test of UHPC segmental box girder which has 160 MPa compressive strength and 15.4 m length was carried out. The effect of steel fibers in combination with reinforcing bars on improving the ductile performance of UHPC box girder was evaluated by comparing the flexural behavior of the UHPC segmental box girders made by the two kinds of mixing portion. The test variables are volume fraction of steel fibers and the arrangement of reinforcing bars. The behavior of UHPC box girder BF2 composed of 1% volume fraction of steel fibers and longitudinal reinforcing bars in web and upper flange with stirrup showed the similar ductile behavior with the girder BF1 composed of 2% volume fraction without stirrup in elastic stress region. But BF1 had the better stiffness and showed the more ductile behavior in inelastic stress region. Segmental interfaces of UHPC box girder have not any crack and slide until the final flexural collapse load.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.81-88
• /
• 2011

This study ascertained the possibility of use of sulfur abstracted from waste sulfur as a construction material through modification process and manufacturing high efficiency modification sulfur with superior quality on dispersibility and hydrophilic in normal temperature. Mechanic, behavior and chemical durability of mortar with added modification sulfur. The results of the study are as follows. The fluidity of mortar mixed with modification sulfur and compressive strength decreased as ratio of mixing of them increases. Flexural, tensile and bond strength of the mortar are also improved and shrinkage of it increases. Especially chemical durability of the mortar showed excellent resistance with the increase of ratio of mixing. Therefore this research has confirmed the modification sulfur can be used as a addmixture for cement.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.125-130
• /
• 2001

Experimental and analytical researches have been conducted on the twin-fluid atomizers for better droplet breakup during the past decades. But, the studies on the disintegration mechanism still present a great challenge to understand the drop behavior and breakup structure. In an effort to describe the aerodynamic behavior of the sprays issuing from the internal mixing counter-swirling nozzle, the spatial distribution of axial (U) radial (V) and tangential (W) components of droplet velocities are investigated across the radial distance at several axial locations of Z=30, 50, 80, 120 and 170mm, respectively. Experiments were conducted for the liquid flow rates which was kept constant at 7.95 g/s and the air injection pressures were varied from 20 kPa to 140 kPa. Counter-swirling internal mixing nozzles manufactured at angles of $15^{\circ},\;30^{\circ},\;45^{\circ}$ and $60^{\circ}$ the central axis with axi-symmetric tangential-drilled holes was considered. The distributions of velocities and turbulence intensities are comparatively analyzed. PDPA is installed to specify spray flows, which have been conducted along the axial downstream distance from the nozzle exit. Ten thousand of sampling data was collected at each point with time limits of 30 second. 3-D automatic traversing system is used to control the exact measurement. It is observed that the sprays with all swirl angle have the maximum SMD for on air injection pressure of 20 kPa and 140 kPa with centerline, respectively. The nozzle with swirl angle of $60^{\circ}$ has vest performance.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2010

The amount of dredging clay will be greatly increased by the eco-rive project and port development in Korea. Geotechnical engineers have thrown their efforts into the new ways for effective re-uses of the dredging clay such as the material for reclamation, and so on. However, very high initial water content and low strength causes unexpected difficulties in the aspect of trafficablility or time for consolidation. Therefore, the injection of cement stabilizer is used as one of ways to improve reclaimed ground. However, it also makes an argument by heavy metal from cement stabilizer. In this paper constant rate of strain consolidation test and normal consolidation test were performed to investigate behavior characteristics of the consolidation about soil-cement include lean mixed cement to reduce the environmental loads by the cement. The experimental results of consolidation characteristics about soil-cement include lean mixed cement influenced by mixing ratio. Especially it was observed that mixing ratio of 4%~6% leads not only the reduction of consolidation settlement, but time for consolidation.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.383-393
• /
• 2008

The etching mechanism of $ZrO_2$ thin films and etch selectivity over some materials in both $BCl_3$/Ar and $BCl_3/CHF_3$/Ar plasmas are investigated using a combination of experimental and modeling methods. To obtain the data on plasma composition and fluxes of active species, global (0-dimensional) plasma models are developed with Langmuir probe diagnostics data. In $BCl_3$/Ar plasma, changes in gas mixing ratio result in non-linear changes of both densities and fluxes for Cl, $BCl_2$, and ${BCl_2}^+$. In this work, it is shown that the non-monotonic behavior of the $ZrO_2$ etch rate as a function of the $BCl_3$/Ar mixing ratio could be related to the ion-assisted etch mechanism and the ion-flux-limited etch regime. The addition of up to 33% $CHF_3$ to the $BCl_3$-rich $BCl_3$Ar plasma does not influence the $ZrO_2$ etch rate, but it non-monotonically changes the etch rates of both Si and $SiO_2$. The last effect can probably be associated with the corresponding behavior of the F atom density.

• Textile Coloration and Finishing
• /
• v.11 no.5
• /
• pp.44-54
• /
• 1999

Poly(ethylene 2,6-naphthalate), PEN, is a relatively well-known polymer used for engineering purposes. Naphthalene ring provides rigidity to the polymer backbone, thus, it elevated the glass transition temperature and enhanced mechanical properties. The structure and properties of PEN affect a processing conditions severely, and the high-thermal stability have been had a poor thermal processibility. Hence, the basic mechanism of solvent drawing, is very much the same as that of thermal drawing from glassy state since both involve the inducement of segmental mobility. The former achieves the goal by use of chemical energy, and the latter does so by use of thermal energy. Generally, the sorption of the solvent by the polymer has a plasticizing effect, and leads to a lowering of the glass transition temperature, $T_g$. In this paper, the dynamic viscoelasticity behavior in liquid-drawing process of an unoriented amorphous PEN films were investigated using Rheovibron. The results are as follows ： (1) For the drawing in silicone oil, the drawing below $T_g$. had $\alpha{2}$-dispersion due to an inhomogeneous taut structure. (2) For the drawing in water, the inhomogeneous taut structure reduced by the effect of plasticization even below $T_g$. (3) For the drawing in butanol, the only aliphatic segment in PEN have some molecular mobility but the mobility of the aromatic segment having naphthalene ring is nearly impossible. (4) For the drawing in dioxane/water mixing solvent, the solvent effect is complementary each other and accordingly the entire molecular conformation have stable state. (5) For the drawing in dioxane/butanol mixing solvent, the inhomogeneity of the taut structure and the aromatic segment increase with increasing the temperature and this tendencies correspond with that of the draw ratio.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.11
• /
• pp.1494-1500
• /
• 2012

Fermentation with filamentous fungi in a bioreactor is a complex dynamic process that is affected by flow conditions and the evolution of the rheological properties of the medium. These properties are mainly affected by the biomass concentration and the morphology of the fungus. In this work, the rheological properties of a fermentation with the fungus Beauveria bassiana under different hydrodynamic conditions were studied and the rheological behavior of this broth was simulated through a mixture of carboxymethyl cellulose sodium and cellulose fibers (CMCNa-SF). The bioreactor was a 10 L CSTR tank operated at different stir velocities. Rheological results were similar at 100 and 300 rpm for both systems. However, there was a significant increase in the viscosity accompanied by a change in the consistence index, calculated according to the power law model, for both systems at 800 rpm. The systems exhibited shear-thinning behavior at all stir velocities, which was determined with the power law model. The mixing time was observed to increase as the cellulose content in the system increased and, consequently, the efficiency of mixing diminished. These results are thought to be due to the rheological and morphological similarities of the two fungal systems. These results will help in the optimization of scale-up production of these fungi.