• Korean Journal of Food Science and Technology
• /
• v.23 no.6
• /
• pp.739-744
• /
• 1991

A palatable paste-type lactic fermented rice (LFR) was prepared by lactic acid fermentation after liquefaction and saccharification of cooked rice. A mixed culture of Lactobacillus bulgaricus and Streptococcus thermophilus (1 : 1) produced the LFR of the best quality. A great improvement in quality of the LFR was achieved by 0.02% each ${\alpha}-amylase$ and glucoamylase treatment during the fermentation (simultaneous saccharification and fermentation), which resulted from the increased sourness and sweetness and the decreased size of solid particles contained in the LFR. The resulted LFR was superior in quality. Physical and chemical properties of the LFR were evaluated.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.297-301
• /
• 2004

Nano-sized mullite (3Al$_2$O$_3$$.$2SiO$_2$) colloids were prepared by use of the spray combustion method. For combustion reaction, Al(NO$_3$)$_3$$.$9$H_2O$, and CH$_{6}$N$_4$O were used as an oxidizer and a fuel respectively, and then colloidal silica was also added as 2SiO$_2$source for mullite. The temperature of the reaction chamber was kept at 80$0^{\circ}C$ to initiate the ignition of droplets of the mixed precursors. For preventing droplet coagulation, the droplet number concentration was reduced using the metal screen filter, and the residence time of aerosol was kept at 2.5 seconds for laminar flow. The synthesized colloidal particles had an uniform spherical shape with 130 nanometer size and the crystalline phase showed the mullite with stoichiometry in the observations of XRD and TEM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.111-120
• /
• 1998

In this paper, the $(SrPb)(CaMg)TiO_3$ ceramics with paraelectric properties were fabricated by the mixed oxide method. It was investigated that which the variation of contents of $Bi_2O_3{\cdot}3TiO_2$ effects on structural, dielectrical and electrical properties of specimens. As a result, the grain size were grown with increasing the contents of $Bi_2O_3{\cdot}3TiO_2$. The relative dielectric constants were increased up to 4[mol%] of $Bi_2O_3{\cdot}3TiO_2$, and decreased more or less at a low temperature in the specimens which had more than. But the temperature coefficient. of capacitance were showed ${\pm}25$[%]. The dielectric loss were less than 0.05 in all specimens which had more than 4[mol%] of $Bi_2O_3{\cdot}3TiO_2$. In order to investigate the behavior of charged particles, the characteristics of electrical conduction were measured. As a result, the conduction current was divided into the three steps as a function of DC electric field. The first step was Ohmic region due to ionic conduction, below 15[kV/cm]. The second step was showed a saturation which seems to be related to a depolarizing field occuring in field-enforced ferroelectric phase, between 15[kV/cm] and 40[kV/cm]. The third step was attributed to Child's law related to space charge which injected from electrode, above 40[kV/cm].

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.486-490
• /
• 2012

$La_{7.33}Bi_2(SiO_4)_6O_2$ specimens were fabricated by standard solid-state synthesis route for solid oxide electrolytes. The calcined powders exhibited uniform particles with a mean particle size of about $28{\mu}m$. The room-temperature structure of $La_{7.33}Bi_2(SiO_4)_6O_2$ specimens was analyzed as hexagonal, space group P63 or P63/m, and the unit cell volume increased with increase a sintering temperature. The specimens sintered at $1,175^{\circ}C$ showed X-ray patterns of homogeneous apatite single phase without the second phase such as $La_2Si_2O_7$ and $La_2SiO_5$. The specimen sintered at $1,175^{\circ}C$ showed the maximum sintered density of 5.49 $g/cm^3$. Increasing the sintering temperature, total conductivities increased, activation energy decreased and the values were $1.98{\times}10^{-5}Scm-1$ and 1.23 eV, respectively.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.6
• /
• pp.32-37
• /
• 2006

Micron size Co-alloy(T800) powder was coated on Inconel 718 by HVOF thermal spraying for the studies of the improvement of durability of high speed spindle by using Taguchi program for the parameters of spray distance, flow rates of hydrogen and oxygen and powder feed rate. The optimal coating process was determined by the studies of coating properties such as micro-structure, porosity, surface roughness and micro hardness. Friction and wear behaviors of coatings were investigated by sliding wear test at room temperature and $1000^{\circ}F(538^{\circ}C)$. At both room temperature and $538^{\circ}C$ the sliding wear debris and friction coefficients of the coating were drastically reduced compared with the surface of non-coated parent material. This shows that Co-alloy powder coating is highly recommendable for the durability improvement surface coating of high speed air-bearing spindle. At high temperature wear traces and friction coefficients of both coating and non-coating were drastically reduced compared with those of room temperature since the brittle oxides were formed easily on the surface, and the brittle oxide phases were attrited by the reciprocating sliding wear according to the complicated mixed wear mechanisms These oxide particles, partially melts and the melts play role as lubricant and reduce the wear and friction coefficient. This also shows that Co-alloy powder coating is highly recommendable far the durability improvement surface coating on the surface vulnerable to frictional heat such as high speed spindles.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.5
• /
• pp.199-203
• /
• 2004

Superconducting B $i_2$S $r_2$C $a_{n-l}$C $u_{n}$ $O_{x}$(n=2～4) thin films were prepared by single target DC-magnetron sputtering. And, that was compared with the B $i_2$S $r_2$C $a_{n-l}$C $u_{n}$ $O_{x}$(n=1～3) thin film fabricated by using the ion beam sputtering. Phase intergrowth among n=2-3, 3-4 and 4-5 phases was observed. The molar fraction of each phase in the mixed crystal of the deposited films was determined by x-ray diffraction analyses and investigated as a function of $O_2$ gas pressure during sputtering. We investigated the changes of the superconducting properties by molar fraction of each phase. Also, the thin film surface observation was carried out by atomic force microscope. The images show the average particle size decreases, and the distribution density of particles on the film surface was to increase with lower gas pressures. The fabrication conditions for selective growth of the single n=2, 3 and 4 phases in BiSrC $a_{n-l}$C $u_{n}$ $O_{x}$(n=2～4) thin film are discussed.e discussed.ussed.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.184-191
• /
• 2001

Recently, as industrialization is rapidly growing and the standard of life is rising, the quantities of waste glasses have been hastily increased and most of them are not recycled but abandoned. It cause some problems such as the waste of natural resources and environmental pollution. Therefore, this study was conducted basic experimental research to analyze the possibilities of recycling of waste glasses(crushed waste glasses outbreaking from our country such as amber, emerald-green, flint and mixed) as fine aggregates for concrete. Test results of fresh concrete, slump and compacting factors decrease because grain shape is angular and air content increase due to involving small size particles so much in waste glasses. Also compressive, tensile and flexural strengths decrease with increase of the content of waste glasses. In conclusion, the content of waste glasses below 30% is reasonable and usage of pertinent admixture is necessary to obtain workability and air content.

• Journal of the Korean Magnetics Society
• /
• v.5 no.6
• /
• pp.921-927
• /
• 1995

The micro particle,s shapes of the magnetic films obtained by electrode position of Iron ions and Cobalt-Iron mixed ions in aluminum anodic oxidized films are dependent on the size of particle diameter. When the diameter of deposited particles is larger than $300\AA$, the film plane anisotropy caused by bottom extremity increases, and the crystalization orientation of FeC deposited unusually in the part of the bottom extremities affects on the coercive force Hc and the magnetic anisotropy energy Ku. It was confirmed that the shape anisotropy of particle affects on the both Hc and Ku because the FeC did not deposit in the Iron deposited samples entirely, but in the Cobalt-Iron alloy deposited samples, the effects by the very strong crystalization orientation of the FeC is larger than that of the shape anisotropy. From these results, the Cobalt-Iron alloyed films could switchover the film plane magnetic anisotropy to the perpendicular magnetic anisotropy energy by using the constrainting method of FeC deposition with Cu deposition instead of Cobalt-Iron alloy in the bottom extremities.

• Smart Structures and Systems
• /
• v.23 no.1
• /
• pp.81-90
• /
• 2019

The shear behavior of soil-concrete interface is mainly affected by the surface roughness of the two contact surfaces. The present research emphasizes on investigating the effect of roughness of soil-concrete interface on the interface shear behavior in two-layered laboratory testing samples. In these specially prepared samples, clay silt layer with density of $2027kg/m^3$ was selected to be in contact a concrete layer for simplifying the laboratory testing. The particle size testing and direct shear tests are performed to determine the appropriate particles sizes and their shear strength properties such as cohesion and friction angle. Then, the surface undulations in form of teeth are provided on the surfaces of both concrete and soil layers in different testing carried out on these mixed specimens. The soil-concrete samples are prepared in form of cubes of 10*10*30 cm. in dimension. The undulations (inter-surface roughness) are provided in form of one tooth or two teeth having angles $15^{\circ}$ and $30^{\circ}$, respectively. Several direct shear tests were carried out under four different normal loads of 80, 150, 300 and 500 KPa with a constant displacement rate of 0.02 mm/min. These testing results show that the shear failure mechanism is affected by the tooth number, the roughness angle and the applied normal stress on the sample. The teeth are sheared from the base under low normal load while the oblique cracks may lead to a failure under a higher normal load. As the number of teeth increase the shear strength of the sample also increases. When the tooth roughness angle increases a wider portion of the tooth base will be failed which means the shear strength of the sample is increased.

• Korean Journal of Materials Research
• /
• v.20 no.12
• /
• pp.669-675
• /
• 2010

One of the greatest challenges for our society is providing powerful electrochemical energy conversion and storage devices. Rechargeable lithium-ion batteries and fuel cells are among the most promising candidates in terms of energy and power density. As the starting material, $TiCl_4{\cdot}YCl_3$ solution and dispersing agent (HCP) were mixed and synthesized using ammonia as the precipitation agent, in order to prepare the nano size Y doped spherical $TiO_2$ precursor. Then, the $Li_4Ti_5O_{12}$ was synthesized using solid state reaction method through the stoichiometric mixture of Y doped spherical $TiO_2$ precursor and LiOH. The Ti mole increased the concentration of the spherical particle size due to the addition of HPC with a similar particle size distribution in a well in which $Li_4Ti_5O_{12}$ spherical particles could be obtained. The optimal synthesis conditions and the molar ratio of the Ti 0.05 mol reaction at $50^{\circ}C$ for 30 minutes and at $850^{\circ}C$ for 6 hours heat treatment time were optimized. $Li_4Ti_5O_{12}$ was prepared by the above conditions as a working electrode after generating the Coin cell; then, electrochemical properties were evaluated when the voltage range of 1.5V was flat, the initial capacity was 141 mAh/g, and cycle retention rate was 86%; also, redox reactions between 1.5 and 1.7V, which arose from the insertion and deintercalation of 0.005 mole of Y doping is not a case of doping because the C-rate characteristics were significantly better.