• 한국정밀공학회지
• /
• 제11권5호
• /
• pp.153-160
• /
• 1994

In this study, residual stress and surface roughness were investigated experimentally to evaluate surface integrity on surface layer machined by CBN, ceramics and WC cutting tools. When machining difficult-to-cut material (hardened STD11 steel $H_{R}$C 60), residual stresses remaining in machined surface layer were mainly compressive. The increase of flank wear caused a shift of the compressive residual stress maximum to greater workpiece depths, but the changes did not penetrate the workpiece beneath a depth of 300 .mu. m. Surface roughness was influenced considerably by variations of the cutting speed and feed. In machining hard material, CBN and A1$_{2}$ $O_{3}$ ceramics cutting tool materials proved significantly superior to mixed ceramics A1$_{2}$ $O_{3}$-TiC and WC in evaluation of surface integrity.y.

• 열처리공학회지
• /
• 제26권3호
• /
• pp.105-112
• /
• 2013

The microstructural changes of Fe-20Mn-12Cr-1Cu alloy have been studied during high temperature gas nitriding (HTGN) at the range of $1000^{\circ}C{\sim}1150^{\circ}C$ in an atmosphere of nitrogen gas. The mixed microstructure of austenite and ${\varepsilon}$-martensite of as-received alloy was changed to austenite single phase after HTGN treatment at the nitrogen-permeated surface layer, however the interior region that was not affected nitrogen permeation remained the structure of austenite and ${\varepsilon}$-martensite. With raising the HTGN treatment temperature, the concentration and permeation depth of nitrogen, which is known as the austenite stabilizing element, were increased. Accordingly, the depth of austenite single phase region was increased. The outmost surface of HTGN treated alloy at $1000^{\circ}C$ appeared Cr nitride. And this was in good agreement with the thermodynamically calculated phase diagram. The grain growth was delayed after HTGN treatment temperature ranges of $1000^{\circ}C{\sim}1100^{\circ}C$ due to the grain boundary precipitates. For the HTGN treatment temperature of $1150^{\circ}C$, the fine grain region was shown at the near surface due to the grain boundary precipitates, however, owing to the depletion of grain boundary precipitates, coarse grain was appeared at the depth far from the surface. This depletion may come from the strong affinity between nitrogen and substitutional element of Al and Ti leading the diffusion of these elements from interior to surface. Because of the nitrogen dissolution at the nitrogen-permeated surface layer by HTGN treatment, the surface hardness was increased above 150 Hv compared to the interior region that was consisted with the mixed microstructure of austenite and ${\varepsilon}$-martensite.

• 한국지반공학회지:지반
• /
• 제14권1호
• /
• pp.49-58
• /
• 1998

폐타이어가 지반의 동상방지 건설재료로서 재사용될 수 있는지를 연구하였다. 동상방지에 대한 폐타이어의 기본적인 효과를 검토하기 위해 화강풍화토에 폐타이어가루를 몇 가지의 비율로 혼합해서 준비한 시료로서 영하 $17^{\circ}$하에서 동상시험과 화강풍화토에 대한 동결깊이시험을 실내에서 수행하였다. 역청포장의 보조기층 바로 아래에 폐타이어조각을 혼합한 쇄석층을 동상방지층으로 둠으로서 실용상으로 효과적이라는 사실을 알게 되었다. 그리고 이 동상방지 층의 소요두께와 동결 지수와의 관계식을 제안하였다.

• Transactions on Electrical and Electronic Materials
• /
• 제10권3호
• /
• pp.89-92
• /
• 2009

High-quality Al-N doped p-type ZnO thin films were deposited on Si and buffer layer/Si by DC magnetron sputtering in a mixture of $N_2$ and $O_2$ gas. The target was ceramic ZnO mixed with $Al_2O_3$ (2 wt%). The p-type ZnO thin films showed a carrier concentration in the range of $1.5{\times}10^{15}{\sim}2.93{\times}10^{17}\;cm^{-3}$, resistivity in the range of 131.2${\sim}$2.864 ${\Omega}cm$, mobility in the range of 3.99${\sim}$31.6 $cm^2V^{-1}s^{-l}$, respectively. It was easier to dope p-type ZnO films on Si substrates than on buffer layer/Si. The film grown on Si showed the highest quality of photoluminescence (PL) characteristics. The Al donor energy level depth $(E_d)$ of Al-N codoped ZnO films was reduced to about 50 meV, and the N acceptor energy level depth $(E_a)$ was reduced to 63 meV.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2018년도 추계학술발표대회
• /
• pp.686-689
• /
• 2018

3D 손 포즈 추정(Hand Pose Estimation, HPE)은 스마트 인간 컴퓨터 인터페이스를 위해서 중요한 기술이다. 이 연구에서는 딥러닝 방법을 기반으로 하여 단일 RGB-Depth 카메라로 촬영한 양손의 3D 손 자세를 실시간으로 인식하는 손 포즈 추정 시스템을 제시한다. 손 포즈 추정 시스템은 4단계로 구성된다. 첫째, Skin Detection 및 Depth cutting 알고리즘을 사용하여 양손을 RGB와 깊이 영상에서 감지하고 추출한다. 둘째, Convolutional Neural Network(CNN) Classifier는 오른손과 왼손을 구별하는데 사용된다. CNN Classifier 는 3개의 convolution layer와 2개의 Fully-Connected Layer로 구성되어 있으며, 추출된 깊이 영상을 입력으로 사용한다. 셋째, 학습된 CNN regressor는 추출된 왼쪽 및 오른쪽 손의 깊이 영상에서 손 관절을 추정하기 위해 다수의 Convolutional Layers, Pooling Layers, Fully Connected Layers로 구성된다. CNN classifier와 regressor는 22,000개 깊이 영상 데이터셋으로 학습된다. 마지막으로, 각 손의 3D 손 자세는 추정된 손 관절 정보로부터 재구성된다. 테스트 결과, CNN classifier는 오른쪽 손과 왼쪽 손을 96.9%의 정확도로 구별할 수 있으며, CNN regressor는 형균 8.48mm의 오차 범위로 3D 손 관절 정보를 추정할 수 있다. 본 연구에서 제안하는 손 포즈 추정 시스템은 가상 현실(virtual reality, VR), 증강 현실(Augmented Reality, AR) 및 융합 현실 (Mixed Reality, MR) 응용 프로그램을 포함한 다양한 응용 분야에서 사용할 수 있다.

• 한국해양공학회지
• /
• 제1권2호
• /
• pp.101-112
• /
• 1987

Fracture toughness characterization in the transition region is examined for heat-treated and ionnitrided Ni-Cr-Mo steel. After heat treatment for the specimens of Ni-Cr-Mo steel, organizations of specimens-specimens which are heat-treated and ion-nitrided for 4 hours at 500 .deg. C and 5 torr in 25%N/dub 2/-75%H/sub 2/mixed gas-, hardness variety, and X-ray diffraction pattern of the ion-nitriding compound layer are observed. Fracture toughenss test of unloading compliance method were conducted over the regions from room trmperature to -70.deg. C. The compound layer was consisted of r'=Fe/sub 4/N phase and ion-nitrided layer's depth was 200mm from surface. The transition regions of heat-treated and ion-nitrided specimens were about -30.deg. C and -50.deg. C, respectively. The transition region of ion-nitrided specimens is estimated less than that of heat-treated one, and this is the effect of ion-nitriding.

• 생태와환경
• /
• 제35권1호통권97호
• /
• pp.10-20
• /
• 2002

소양호와 팔당호에 대한 한강수질검사소(1996${\sim}$1998)와 환경부(1990${\sim}$1997), 그리고 건설교통부(1996${\sim}$1998)자료를 인용하여 수문학적 특성에 따른 소양호와 팔당호의 수질특성 및 계절적 변화양상을 비교${\cdot}$분석하였다. 소양호에서는 수온차에 의한 뚜렷한 성층현상이 관찰되었다. 춘계와 하계에 관찰된 좁은 폭의 표층은 추계로 갈수록 점차 넓어진 반면 중층의 폭은 좁아지는 경향을 보였으며 심층은 연중 수온이 $5^{\circ}C$내외로 거의 변동을　보이지 않았다. 춘계와 하계에는 표층에서 용존산소의과포화가 관찰되었고, 추계로 들어가면서 표층과 중층의　용존산소 포화도는 약 75%까지,　심층은 45${\sim}$55%까지　감소하였으며 빈산소　수괴가 시간의 흐름에 따라 심층으로 이동하는 현상이 관찰되었다. 우기동안에는 중층에서 약 $50\;{\mu}S/cm$의 가장 낮은 전기전도도를 갖는 수괴가　분포하고 있음이 관찰되었다. 팔당호에서 수심별 수은의 분포는 연도별,　계절별 구분 없이 비교적 잘 혼합된 수괴의 특성이 관찰되었으나$5{\sim}9$월에는 상${\cdot}$하층이 약 $5^{\circ}C$내외의 수온차이를 나타냈다. 용존산소포화도는 연중 90% 이상으로 소양호에 비해 높은 산소포화도가 관찰되었다. 초여름부터 초가을까지 표층에서는 과포화가, 심층에서는 60%정도까지 낮은 포화도가 관찰되었다. 늦은 봄부터 초가을 (우기)의전기전도도는 수심 $4{\sim}5\;m$ 이하의 수층에서 $90\;{\mu}S/cm$정도까지 감소하여 표층보다 낮은 값을 보였다. 그러나,늦은 가을부터 초봄까지의 전기전도도는 약 $10^{\circ}Cm$깊이까지 표층이 심층보다 낮게 관찰되었다. 소양호의 체류시간은 평균 245일로, 팔당호의 평균 5.1일과 큰 차이를 보였으나, 팔당호는 소양호보다 클로로필 3농도는 약 2.7배, 총 질소 농도는 약 1.2배 그리고 총 인 농도는 약 2.6배 높았다. 따라서 영양염류 농도가 체류시간보다 조류증식에 더 기여한 것으로 판단된다.

• 열처리공학회지
• /
• 제9권1호
• /
• pp.69-77
• /
• 1996

The fatigue crack initiation behavior of plasma ion nitrided SACM645 steel was investigated through the rotary bending fatigue test and residual stress measurement by XRD. It was shown by XRD and EPMA that the plasma ion nitrided surface was composed of ${\gamma}^{\prime}(Fe_4N)$phase and ${\varepsilon}(Fe_{2-3}N)$phase, and that the nitrogen atoms existed in Fe matrix in diffusion layer. The OM, SEM and Auger spectroscopy showed that the depth of compound layer, mixed compound and diffusion layer, and diffusion layer was $8{\mu}m$, $30{\mu}m$ and $300{\mu}m$, respectively. However, the microhardness test showed that the depth of hardened layer was $500{\mu}m$. The tensile strength of the ion nitrided SACM645 was lower than that of the unnitrided SACM645, and the ion nitrided specimen was fractured without plastic deformation. The nitrided SACM645 showed much poorer low cycle fatigue properties than the unnitrided one. In rotary bending fatigue, the fatigue strength of the ion nitrided SACM645 was higher than that of the unnitrided specimen, and the fatigue crack initiation sites changed by applied fatigue stress levels. The XRD result showed that the ion nitrided SACM645 has the compressive residual stress from surface to $600{\mu}m$ deep and the tensile residual stress from $600{\mu}m$ to deeper site. It is thought that crack initiation takes place at the point where the total stress of residual stress and applied stress is maximum.

• Journal of the korean society of oceanography
• /
• 제31권4호
• /
• pp.196-206
• /
• 1996

Vertical profiles of the chlorophyll ${\alpha}$, phytoplankton abundance, nutrients and sigma-t were compared with the vertical distribution of phytoplankton species in conjunction with $^{14}$C primary production in the Southern Waters of the East Sea, Korea. In the upper mixed layer the water column was only weakly stratified and ambient nitrogenic nutrient concentrations were markedly depleted. Dissolved silicate seemed to be another limiting nutrient in the surface layer. The occupation of different water depths by several dominant diatom species was well explained by the degree of silicification of each cell and the silicate concentration of ambient seawater. Subsurface chlorophyll maxima were continuously observed in the lower parts of the euphotic layer and the depth coincided with nutricline, supporting our view that chlorophyll maximum was sustained partially by enhancement of in situ growth of phytoplankton and partially by increase of cellular chlorophyll content. The persistence of chlorophyll maximum layer was attributed to the physiological adaptation of the phytoplankters to low light intensities and to the utilization of regenerated nutrients. Integrated water column production of organic matter by photosynthesis appeared to be better related to phytoplankton cell division than to the cell growth in terms of biosynthesis of pigments and other intracellular components.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.319-320
• /
• 2009

In this study, high-quality Al-N doped p-type ZnO thin films were deposited on n-type Si (100) wafer or Si coated with buffer layer by DC magnetron sputtering in the mixture of $N_2$ and $O_2$ gas. The target was ceramic ZnO mixed with $Al_2O_3$ (2 wt%). The p-type ZnO thin film showed higher carrier concentration $2.93\times10^{17}cm^{-3}$, lower resistivity of $5.349\;{\Omega}cm$ and mobility of $3.99\;cm^2V^{-1}S^{-1}$, respectively. According to PL spectrum, the Al donor energy level depth ($E_d$) of Al-N codoped p-type ZnO film was reduced to about 51 meV, and the N acceptor energy level depth ($E_a$) was reduced to 63 meV, respectively.